• Design & Manufacturing
• /
• v.17 no.1
• /
• pp.1-5
• /
• 2023

In multi-material injection molding, since two or more materials with different process conditions are used, it is essential to maximize process efficiency by operating the cooling or heating system to a minimum. In this study, Liquid silicone rubber (LSR) that can be cured at a low temperature suitable for the multi-material injection molding was selected and the cure behavior according to the process conditions was analyzed through differential scanning calorimetry (DSC). Dynamic measurement results of DSC with different heating rate were obtained, and through this, the total heat of reaction when the LSR was completely cured was calculated. Isothermal measurement results of DSC were derived for 60 minutes at each temperature from 80 ℃ to 110 ℃ at 10 ℃ intervals, and the final degree of cure at each temperature was calculated based on the total heat of reaction identified from the Dynamic DSC measurement results. As the result, it was found that when the temperature is lowered, the curing start time and the time required for the curing reaction increase, but at a temperature of 90 ℃ or higher, LSR can secure a degree of cure of 80% or more. However, at 80 ℃., it was found that not only had a relatively low degree of curing of about 60%, but also significantly increased the curing start time. In addition, in the case of 110 ℃, the parameters were derived from experimental result using the Kamal kinetic model.

• Journal of the Korean Society of Safety
• /
• v.19 no.4 s.68
• /
• pp.1-7
• /
• 2004

This study investigated the effects of aging on the transformation behavior of $Ti-50.1at\%$ Ni alloy by means of differential scanning calorimetry. It was found that aging in the temperature range of $350^{\circ}C\~550^{\circ}C$ induced complex transformation behavior, involving the R-phase and multiple-stage martensitic transformation. Usually aged Ni-rich NiTi alloys undergo martensitic transformation on cooling from high temperatures in two step : B2 to R and then R to Bl9'(normal behavior). But under certain ageing conditions, the transformation can also occur in three or more step(unusual multiple step behavior). In the present study we use differential seaming calorimetry(DSC) for a systematic investigation of the evolution of transformation behavior with ageing temperature and time.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.1015-1019
• /
• 1996

Several alkyl chlorides were brominated using LiBr and $CaBr_2$ adsorbed on alumina in the absence of solvent. The yields of alkyl bromides were fairly high. Such a high reactivity by these bromide salts might be due to the interaction of minute amount of water and the salt on alumina. Differential scanning calorimetry (DSC) thermogram was provided and discussed.

• Journal of the Korean Chemical Society
• /
• v.54 no.6
• /
• pp.717-722
• /
• 2010

Two derivatives of star shaped compounds based on naphthylamine with symmetric trisubstituted benzene as core, methoxy and ethoxy as end substitutions are synthesized. The synthesized compounds are characterized by UV-visible, FT-IR and NMR spectrometric techniques. The electronic and thermal properties of the compounds are studied using cyclic voltametry (CV) and differential scanning calorimetry (DSC) respectively. The data's obtained have similarity with the arylamines that have been already used in optoelectronic devices. So these compounds are interesting materials for applications in such devices.

• Macromolecular Research
• /
• v.14 no.6
• /
• pp.588-595
• /
• 2006

The morphology, structure and melting behaviour of cold-crystallized isotactic polystyrene (iPS) were studied by differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and small angle X-ray scattering (SAXS). The polymer was found to crystallize according to the dual-lamellar stack model. The two populations of lamellae, along with a melting-recrystallization phenomenon, determined the appearance of multiple melting peaks in DSC traces. The annealing peak was attributed to the relaxation of a rigid amorphous phase, rather than to the melting of crystalline material.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2154-2164
• /
• 1995

In this study, a dielectric cure monitoring system which consists of an electric circuit, a sensor and a personal computer was developed to on-line monitor the dielectric properties of carbon fiber epoxy composite materials. Also, the kinetic model of carbon fiber epoxy composite materials was developed by curve fitting of differential scanning calorimetry data. The start and end points of cure and the relationship between the dissipation factor and the degree of cure were obtained by comparing the dissipation factor from the dielectric properties with the degree of cure from the DSC data. The relationship between the dissipation factor and the degree of cure was tested under various temperature profiles.

• Journal of the Korean Society of Safety
• /
• v.34 no.4
• /
• pp.32-40
• /
• 2019

During the manufacturing process of a printed circuit board(PCB), fumes and mists are generated as the ink dries on the PCB surface. The generated fumes and mists are deposited in the dryer wall and the exhaust duct. Deposited fumes and mists may present a fire hazard if the dryer temperature control system fails. In this study, the thermal stability of the fumes and mists deposited in the dryer and ducts has been analyzed by experimental methods such as thermo gravimetric analysis (TGA), differential scanning calorimetry (DSC), auto ignition temperature (AIT), and multiple mode calorimetry(MMC). According to the experimental analyses, experimental samples are likely to generate gas at the temperature ($180{\sim}240^{\circ}C$) that deviates from the normal operating temperature ($150{\sim}156^{\circ}C$). It has been shown that the thermal stability is degraded when the temperature is deviated from the normal operating temperature. In the end, engineering and management safety measures of accidental prevention have been suggested.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.22 no.5
• /
• pp.596-602
• /
• 1993

The Characteristics of Shinsunchalbyeo(Japonica) and Hangangchalbyeo($J{\times}Idica$) starches including physicochemical properties, differential scanning calorimetry(DSC) and enzymatic digestion of lintnerized starches were investigated. Degree of hydrolysis of Hangangchalbyeo starch with 2.2N HCI for 48hr was higher than that of shinsunchalbyeo starch. Absorbance at ${\lambda}_{max}$ 680nm, and ${\lambda}_{max}$ of iodine stained starch decreased upon acid treatment. But water binding capacity, swelling power and solubility considerably increased as hydrolysis progressed. Relative crystallinity of two starches increased with acid treatment, and that of Shinsunchalbyeo starch was higher than that of Hangangchalbyeo starch. DSC data continuously decreased for lintnerization periods, and those of Shinsunchalbyeo starch. DSC data continuously decreased for lintnerization periods, and those of Shinsunchalbyeo starch have higher than those of Hangangchalbyeo starch. The onset temperature of starch by DSC continuously decreased by treatment, but conclusion temperature increased until 24hr and then decreased. The enthalpy for gelatinization decreased for both starches. Degree of hydrolysis of lintnerized Shinsunchalbyeo starch with glucoamylase was slightly higher than that of Hangangchalbyeo starch.

• Korean Journal of Food Science and Technology
• /
• v.21 no.4
• /
• pp.556-561
• /
• 1989

Thermal properties of amylose-lysolecithin (AL) complex, amylose content and effect of lysolecithin on the gelatinization of rice starch were investigated by Differential Scanning Calorimetry (DSC). The melting temperature of AL complex was near to $108.5^{\circ}C$ and the melting enthalpy was about 1.0cal/g. The gelatinization temperature of rice starch was not affected by adding lysolecithin. However, the enthalpy of gelatinization was decreased. The amylose contents in rice varieties were calculated from melting enthalpy of AL complex. The amylose contents for Indica and Japonica types of rice were in the range of 16-19%, which were in good agreement with those determined by iodine binding method. Significant differences were not observed in the amylose contents between Indica and Japonica varieties.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.4
• /
• pp.252-260
• /
• 1996

A study was conducted to examine the precipitation phenomena of Al-2.1Li-2.9Cu alloy by differential scanning calorimetry and transmission electron microscopy. DSC curves were measured over the temperature range of $25{\sim}550^{\circ}C$ at a heating rate of $2{\sim}20^{\circ}C$/min.. Three heat evolution peaks and three heat absorption peaks were observed in the DSC curve for the as-quenched specimen. From DSC results and TEM analysis, it was proved that the precipitation sequence in the as-quenched specimen is supersaturated solid solution ${\rightarrow}$ GP zone ${\rightarrow}{\delta}^{\prime}{\rightarrow}T_1{\rightarrow}T_2$ and ${\theta}^{\prime}$ was detected in the peak aged specimen at $160^{\circ}C$. The major phase formed at peak hardeness in the aging at $160^{\circ}C$ was ${\delta}^{\prime}$ phase. The activation energies for the formation of ${\delta}^{\prime}$ and $T_1$ phases were 22.3kcal/mole and 24.3kcal/mole, respectively. These lower activation energies than those for diffusion of Cu and Li in Al are ascribed to the quenched-in excess vacancies.