• Transactions of the Society of Information Storage Systems
• /
• v.3 no.3
• /
• pp.129-134
• /
• 2007

Boron nitride (BN) is a highly attractive material for wear resistant applications of mechanical components. BN is super hard and it is the second hardest of all known materials. It also has a high thermal stability, high abrasive wear resistance, and in contrast to diamond, BN does not react with ferrous materials. The motivation of this work is to investigate the tribological properties of BN for potential applications in ultra-precision components for data storage, printing, and other precision devices. In this work, the wear characteristics of BN thin films deposited on DLC or Ti buffer layer with silicon substrate using RF-magnetron sputtering technique were analyzed. Wear tests were conducted by using a pin-on-disk type tester and the wear tracks were measured with a surface profiler. Experimental results showed that wear characteristics were dependent on the sputtering conditions and buffer layer. Particularly, BN coated on DLC layer showed better wear resistant behavior. The range of the wear rates for the BN films tested in this work was about 20 to $100{\mu}m^3$/cycle.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04b
• /
• pp.118-120
• /
• 2002

Electro-optical (EO) characteristics of the ion beam (IB) aligned twisted nematic (TN)-liquid crystal display (LCD) with oblique ion beam exposure on the diamond-like carbon (DLC) thin film surface were studied. An excellent voltage-transmittance (V-T) curve of the ion beam aligned IN-LCD was observed with oblique ion beam exposure on the DLC thin film surface for I min. Also, a faster response time for the ion beam aligned TN-LCD with oblique ion beam exposure on the DLC thin film surface for 1 min can be achieved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.526-529
• /
• 2002

We studied the nematic liquid crystal (NLC) aligning capabilities by the UV alignment method on a diamond like carbon (DLC) thin film surface. A good LC alignment by UV exposure on the DLC thin film surface at $200\AA$ of layer thickness was achieved. Also, a good LC alignment by the UV alignment method on the DLC thin film surface was observed at annealing temperature of $180^{\circ}C$. However, the alignment defect of the NLC was observed above annealing temperature of $200^{\circ}C$. Consequently, the good thermal stability of LC alignment by the UV alignment method on the DLC thin film surface can be achieved.

• Journal of the Korean Vacuum Society
• /
• v.15 no.3
• /
• pp.287-293
• /
• 2006

Diamond-like carbon (DLC) film was deposited using benzene $(C_6H_6)$ by r. f-plasma assisted chemical vapor deposition. The tribological properties of the DLC film were tested by rotating ball-on-disc type tribometer isolated by a chamber. The tribological test was performed in air environment of relative humidity ranging from 0 to 90% in order to observe the tribological behavior of the DLC film with the change of humidity. We used steel ball and DLC coated steel ball to investigate the effect of the counterface material. Using steel ball, the friction coefficient of DLC film increased from 0.025 to 0.2 as the humidity increased from 0% to 90%. In case of DLC coated steel ball which didn't form the Fe-rich debris, the friction coefficient showed much lower dependence of humidity as 0.08 in relative humidity 90%. We confirmed that the high humidity dependence of the friction coefficient using steel ball resulted from the increase of debris size with humidity and the formation of Fe-rich debris by the wear of steel ball. And the friction coefficient was immediately dropped when the relative humidity changed from 90% to 0% during test using steel ball. From this result, we confirmed that the effect of the Fe-rich debris on the friction coefficient was that Fe element in debris formed the highly sensitive graphitic transfer layer to humidity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.02a
• /
• pp.110.2-110.2
• /
• 2009

• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.65-74
• /
• 2009

Device quality indium tin oxide (ITO) films are deposited on glass substrates and ultra-thin diamond-like carbon films are deposited as a buffer layer on ITO by a pulsed Nd:YAG laser at 355 nm and 532 nm wavelength. ITO films deposited at room temperature are largely amorphous although their optical transmittances in the visible range are > 90%. The resistivity of their amorphous ITO films is too high to enable an efficient organic light-emitting device (OLED), in contrast to that deposited by a KrF laser. Substrate heating at $200^{\circ}C$ with laser wavelength of 355 nm, the ITO film resistivity decreases by almost an order of magnitude to $2{\times}10^{-4}\;{\Omega}\;cm$ while its optical transmittance is maintained at > 90%. The thermally induced crystallization of ITO has a preferred <111> directional orientation texture which largely accounts for the lowering of film resistivity. The background gas and deposition distance, that between the ITO target and the glass substrate, influence the thin-film microstructures. The optical and electrical properties are compared to published results using other nanosecond lasers and other fluence, as well as the use of ultra fast lasers. Molecularly doped, single-layer OLEDs of ITO/(PVK+TPD+$Alq_3$)/Al which are fabricated using pulsed-laser deposited ITO samples are compared to those fabricated using the commercial ITO. Effects such as surface texture and roughness of ITO and the insertion of DLC as a buffer layer into ITO/DLC/(PVK+TPD+$Alq_3$)/Al devices are investigated. The effects of DLC-on-ITO on OLED improvement such as better turn-on voltage and brightness are explained by a possible reduction of energy barrier to the hole injection from ITO into the light-emitting layer.

• Journal of Surface Science and Engineering
• /
• v.29 no.5
• /
• pp.532-539
• /
• 1996

Diamond-like carbon (DLC) films were deposited on silicon substrates by the plasma decomposition of hydrocarbons under various conditions, and studied by the spectroscopic ellipsometry (SE). We used the effective medium approximation with the dispersion model developed by Forouhi and Bloomer to determine simultaneously both the structure and the optical constants of the DLC films from their ellipsometric spectra. Especially, we investigated the variation of the multilayer structure including the interface layer, of the refractive indices, and of the extinction coefficients as the deposition conditions were varied; substrate pretreatment procedure, hydrocarbon precursors, and the substrate bias voltage were varied.

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.185-189
• /
• 2005

We reported here nano-scale electrical phase-change recording in amorphous $Ge_2Sb_2Te_5$ media using an atomic force microscope (AFM) having conducting probes. In recording process, a pulse voltage is applied to the conductive probe that touches the media surface to change locally the electrical resistivity of a film. However, in contact operation, tip/media wear and contamination could major obstacles, which degraded SNR, reproducibility, and lifetime. In order to overcome tip/media wear and contamination in contact mode operation, we adopted the W incorporated diamond-like carbon (W-DLC) films as a protective layer. Optimized mutilayer media were prepared by a hybrid deposition system of PECVD and RF magnetron sputtering. When suitable electrical pulses were applied to media through the conducting probe, it was observed that data bits as small as 25 nm in diameter have been written and read with good reproducibility, which corresponds to a data density of $1 Tbit/inch^2$. We concluded that stable electrical phase-change recording was possible mainly due to W-DLC layer, which played a role not only capping layer but also resistive layer.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.248-254
• /
• 1998

DLC(Diamond-Like-Carbon) thin film, one of the solid state amorphous carbon films, has been deposited by the method of PECVD (Plasma Enhanced Chemical Vapor Deposition). The structural features have been characterized using both FT-IR Spectroscopy and Raman Scattering. The film is considered to consist of microcrystalline diamond domains and graphitelike carbon domains, which are interconnected by hydrogenated $sp^3$ tetrahedral carbons. This shows a good agreement with the results by I-Vmeasurements. In I-Vstudy, the sudden increase of current has been observed and this phenomenon is understood to be due to the tunneling effect between graphitelike domains. A characteristic feature related to the $\beta$-SiC has been identified in the study of Raman Scattering for the very thin film, which suggests that a buffer layer forms at the interface of the Si substrate and the carbon film.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.02a
• /
• pp.357-357
• /
• 2008