• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2014-2016
• /
• 2004

In order to obtain a low-loss ferroelectric phase shifter, the reflection-type phase shifter with ferroelectric defected ground structure (DGS) resonators has been designed in this paper. The proposed phase shifter is consist of a 3-dB $90^{\circ}$ branch-line hybrid coupler and terminated reflective circuit with tunable ferroelectric DGS resonator. The ferroelectric DGS unit structure can provide high Q resonator characteristic at high frequencies. The design parameters of equivalent circuit for the tunable DGS resonator are derived by using simple circuit analysis method and three-dimensional full wave finite element method. The fabricated phase shifter has an insertion loss of better than 3.4dB at 13.5GHz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.11
• /
• pp.1954-1961
• /
• 2008

Microgrid usually consists of a cluster of distributed generators(DGs), energy storage systems and loads, and can operate in the grid-connected mode and the islanded mode. This paper presents detailed descriptions of two different options for controlling the active power of DGs in the microgrid. One is regulating the power injected by the unit to a desired amount(Unit output power control) and the other is to regulate the flow of active power in the feeder where the unit is installed to a constant(Feeder flow control). Frequency-droop characteristics are used to achieve good active power sharing when the microgrid operates in the islanded mode. The change in the frequency and the active power output of DGs are investigated according to the control mode and the configuration of DGs when the microgrid is disconnected from the main grid. From the analysis, this paper proposes a method to determine the droop constant of DGs operating in the feeder flow control mode. Simulation results using the PSCAD/EMTDC are presented to validate the approach, which shows good performance as opposed to the conventional one.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.5
• /
• pp.266-274
• /
• 2004

This paper presents a scheme for the interconnection of dispersed generator systems(DGs) based on load .unbalance and load model in composite distribution systems. Groups of each individual load model consist of residential, industrial, commercial, official and agricultural load. The unbalance is involved with many single-phase line segment. . Voltage profile improvement and system loss minimization by installation of DGs depend greatly on how they are placed and operated in the distribution systems. So, DGs can reduce distribution real power losses and replace large-scale generators if they are placed appropriately in the distribution systems. The main idea of solving fuzzy goal programming is to transform the original objective function and constraints into the equivalent multi-objectives functions with fuzzy sets to evaluate their imprecise nature for the criterion of power loss minimization, the number or total capacity of DGs and the bus voltage deviation, and then solve the problem using genetic algorithm. The method proposed is applied to IEEE 13 bus and 34 bus test systems to demonstrate its effectiveness.

• Advances in Energy Research
• /
• v.6 no.1
• /
• pp.55-73
• /
• 2019

The cost incurred by voltage sag effect in power networks has always been of important concern for discussions. Due to the environmental constraints, fossil fuel shortage crisis and low efficiency of conventional power plants, decentralized generation and renewable based DG have become trends in recent decades; because DGs can reduce the voltage sag effect in distribution networks noticeably; therefore, optimum allocation of DGs in order to maximize their effectiveness is highly important in order to maximize their effectiveness. In this paper, a new method is proposed for calculating the cost incurred by voltage sag effect in power networks. Thus, a new objective function is provided that comprehends technical standards as minimization of the cost incurred by voltage sag effect, active power losses and economic criterion as the installation and maintenance costs of DGs. Considering operational constraints of the system, the optimum allocation of DGs is a constrained optimization problem in which Lightning Attachment procedure optimization (LAPO) is used to resolve it and is the optimum number, size and location of DGs are determined in IEEE 33 bus test system and IEEE 34 bus test system. The results show that optimum allocation of DGs not only reduces the cost incurred by voltage sag effect, but also improves the other characteristics of the system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.8 s.99
• /
• pp.815-824
• /
• 2005

In this paper, we proposed a new DGS(Defected Ground Structure) Doherty amplifier for IMT-2000 band. Originally, active load-pull analysis of a Doherty amplifier assumes ideal harmonic termination condition. However, there have been no papers considering this ideal harmonic termination condition. We obtained excellent improvements of efficiency, gain, maximum output power as well as superior size reduction of a Doherly amplifier by satisfying the overlooked assumption of ideal harmonic termination through the adaptation of DGS at the output transmission line of carrier and peaking amplifier that is essential for Doherty operation. The amount of both the 2nd and the 3rd harmonic rejection of the proposed DGS Doherty amplifier over the conventional one are 44.92 dB and over 23.77 dB, respectively. The acquired improvement in Pl dB, gain, drain efficiency, and ACPR to WCDMA 1FA signal were 0.42 dB, 0.33 dB, $6.4\%$ and 5.4 dBc, respectively. Moreover, electrical length of $90{\circ}$ is reduced at each of the DGS carrier amplifier path and DGS peaking amplifier path, therefore the whole amplifier circuit size is considerably reduced.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.4
• /
• pp.243-248
• /
• 2015

Since phase noise is one of the most important parameters in the design of microwave oscillators, several methods have been proposed to reduce the phase noise. These methods have focused on improving the quality factor of resonators, which result in low phase noise oscillators. Dielectric resonators have been widely used for low phase noise in microwave oscillators due to their high quality factor. However this cannot be used in MMIC oscillators because they have a 3D structure. In this paper, to overcome this problem a novel resonator using open ring type DGS is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator, and oscillator for 5.8GHz band is designed using proposed DGS resonator. The open ring type DGS resonator is composed of DGS cell etched on ground plane under $50{\Omega}$ microstrip line. At the fundamental frequency of 5.8GHz, 6.1dBm output power and -82.7 dBc@100kHz phase noise have been measured for oscillator with ring type DGS resonator. The phase noise characteristics of oscillator is improved about 96.5dB compared to one using the general ${\lambda}/4$ microstrip resonator.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.6 s.97
• /
• pp.594-602
• /
• 2005

In this paper, a new type of 5-pole low pass filter(LPF) having defected ground structure(DGS) and very wide transmission line elements is proposed. The previously presented design method of 3-stage LPF using DGS is generalized to design N-pole LPFs for $N\geq5$. As an example, a 5-pole LPF having DGS is designed and measured. The accurate curve-fitting method to determine the series inductors in the prototype filter, and ultimately the size of DGS is described. The proposed 5-pole LPF has transmission line elements with a very low impedance to realize the required shunt capacitance instead of open stubs. Therefore, open stub. Therefore, open stub, Tee-junction, Cross-junction, and high impedance line are not required for the proposed LPF, while they all have been essential in conventional LPFs.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.9
• /
• pp.841-848
• /
• 2016

In this paper, a microstrip-fed dual-band monopole antenna with DGS(: Defected Ground System) for WLAN(: Wireless Local Area Networks) applications was designed, fabricated and measured. The proposed antenna is based on a microstrip-fed structure, and composed of two strip lines and DGS structure and then designed in order to get dual band characteristics. We used the simulator, Ansoft's High Frequency Structure Simulator(: HFSS) and carried out simulation about parameters W2, L10, W3, and DGS to get the optimized parameters. The proposed antenna is made of $21.0{\times}36.0{\times}1.6mm3$ and is fabricated on the permittivity 4.4 FR-4 substrate. The experiment results are shown that the proposed antenna obtained the -10 dB impedance bandwidth 700 MHz(2.10~2.80 GHz) and 1,780 MHz(5.02~6.80 GHz) covering the WLAN bands. Also, the measured gain and radiation patterns characteristics of the proposed antenna are presented at required dual-band(2.4GHz band/5.0GHz band), respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.4
• /
• pp.765-770
• /
• 2009

This paper presents a new open stub structure of Kuroda low-pass filter using DGS(Defected Ground Structure). The open stub having 130ohm is made with equivalent new structure using DGS. This method enable to the fabrication of Kuroda low-pass filter by extending width of the line. In case of FR4(er=4.8, h=0.7874mm), the width of open stub(130ohm) is under 0.1mm. But, the width of open stub using DGS can extend to the width of 0.5mm. 5th order Kuroda low-pass filter design using open stub with DGS shows excellent agreement between theoretical simulation and experimental results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.6
• /
• pp.946-951
• /
• 2000

In this paper, we showed the characteristic of transmission line with DCS (Defected Ground Structure), which is etched on the metallic ground plane. And we extracted the equivalent element value of DGS section. Effects of a lumped element placed on DGS section were investigated by employing DGS of dumbbell shape and parallel resonator with DGS. Chip type resistor, inductor, and capacitor were chosen as lumped elements for experiments. Experimental results show that the Q-factor and resonant frequency of the proposed DGS section can be controlled directly by using the external lumped element.