• 전기학회논문지
• /
• 제57권1호
• /
• pp.52-57
• /
• 2008

In the transformer that is used for the contactless power transmission system, the primary and secondary sides are separated structurally unlike general transformers. When the contactless transformer is built, it forms relatively bigger air gap than the general transformer. Thus it is difficult to transfer energy from the primary side input to the secondary side output with high power efficiently because of low coupling coefficient. This paper proposes a contactless transformer using the rectangular type core that maintains high coupling coefficient even when it has relatively large air gap. The performance characteristics of the proposed transformer are compared with the transformer using general EE core to the air gap variation. The proposed contactless system using rectangular type core and dc-dc full bridge converter, and the system using EE core type and dc-dc full bridge converter are respectively implemented and their performance characteristics are verified by the simulation and experiment.

• Journal of Power Electronics
• /
• 제18권6호
• /
• pp.1634-1641
• /
• 2018

This study focuses on a high-performance direct active and reactive power controller design that is successfully applicable to three-phase pulse width modulation (PWM) AC/DC converters used in renewable distributed energy generation systems. The proposed controller can overcome the sluggish transient dynamic response of conventional controllers to rapid power command changes. Desired active and reactive powers can be thoroughly obtained at the end of each PWM period through a deadbeat solution. The proposed controller achieves an exact nonlinear cross-coupling decoupling of system power without using a predefined switching table or bang/bang hysteresis control. A graphical and analytical analysis that naturally leads to a control voltage vector selection is provided to confirm the finding. The proposed control strategy is evaluated on a 3 kW PWM AC/DC converter in the simulation and experiment.

• 한국전자파학회논문지
• /
• 제18권8호
• /
• pp.895-903
• /
• 2007

임의의 종단 임피던스를 갖는 DC block을 정합하기 위한 새로운 설계식이 소개되었으며, 이 설계식을 이용한 microstrip DC block이 제작, 측정되었다. 기존의 DC block은 완전히 정합기지 않았기 때문에, 한 단자에서 여기 된 power가 다른 단자로 모두 전달되지 않는 문제점이 있었다, 이런 문제점을 해결하기 위하여, 한 단자의 등가 공진기 회로를 제시하였으며, 이 등가회로를 이용하여, coupling coefficient에 관계없이, 어느 경우에도 완전 정합을 이룰 수 있는 설계식을 유도했다. 이 설계식을 이용하여 측정된 microstrip DC block의 삽입, 반사 손실은 중심 주파수 4.1 GHz에서 0.82dB, -31dB를 보였으며, 이 측정 결과는 예상된 결과와 잘 일치함을 보여주고 있다.

• 전력전자학회논문지
• /
• 제27권6호
• /
• pp.515-525
• /
• 2022

The wireless power transfer (WPT) charging system for AGV depends highly on the coupling conditions due to air gap variation. To attain stable output power with high transfer efficiency under various coupling conditions, a single-stage, DC-DC converter that operates with robustness to changes in air gaps is proposed for the WPT system. The proposed converter is capable of soft switching under the set input voltage (V_in: 380 V_DC), load conditions (0-1 kW), and air gap changes (30-70 mm). In addition, a wide output voltage range (Vo: 39-54 V_DC) can be controlled by varying the link voltage due to the phase control at a fixed switching frequency. Experimental results are verified using a prototype of a 1 kW wireless power charging system.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권4호
• /
• pp.483-491
• /
• 2012

It is expected that, in the future, DC power service will be widely used for photovoltaic home power generation systems, since DC consuming devices are ever increasing. Instead of using multiple converters to convert DC to AC and then AC to DC, the power service could solely be based on DC. This would eliminate the need for converters, reducing the cost, complexity, and possibly increasing the efficiency. However, configuration of direct DC power service with mechanical contacts can cause spark voltage or an electric shock when the switch is turned on and off. To solve these problems, in this paper, a contactless power supply for a DC power service that can transfer electric power produced by photovoltaics to the home electric system using magnetic coupling instead of mechanical contacts has been proposed. The proposed system consists of a ZVS boost converter, a half-bridge LLC resonant converter, and a contactless transformer. This proposed contactless system eliminates the use of DC switches. To reduce the stress and loss of the boost converter switching devices, a lossless snubber with coupled inductor is applied. In this paper, a switching frequency control technique using the contactless voltage sensing circuit is also proposed and implemented for the output voltage control instead of using additional power regulators. Finally, a prototype consisted of 150W boost converter has been designed and built to demonstrate the feasibility of the proposed contactless photovoltaic DC power service. Experimental results show that 74~83% overall system efficiency is obtained for the 10W~80W load.

• E2M - 전기 전자와 첨단 소재
• /
• 제5권4호
• /
• pp.393-399
• /
• 1992

In order to increase the coupling strength between bisphenol-A type epoxy resin and filler SiO$_{2}$ it was treated to filler with silane coupling agent[KBM-603]. To observe how silane coupling agent effects on dielectric breakdown strength of Epoxy/SiO$_{2}$ compound material, specimens of eight type were made like following. (A-1, A-2), (B-1, B-2), (C-1, C-2), (D-1, D-2) (see 2-2. Specimen) Specimen treated with silane coupling agent had always bigger dielectric breakdown strength than non-treated specimen. Under the influence of silane coupling agent, increment ratio of dielectric breakdown strength at specimen manufactured by hand drill was very bigger than that of specimen inserted spherical electrode. Therefore, as the specimen shape was varied, it was studied on effect that silane coupling agent affects on dielectric breakdown strength of Epoxy/SiO$_{2}$ compound material.

• 한국광학회:학술대회논문집
• /
• 한국광학회 1990년도 제5회 파동 및 레이저 학술발표회 5th Conference on Waves and lasers 논문집 - 한국광학회
• /
• pp.219-221
• /
• 1990

Y-branch directional coupler type optical modulators with three different coupling lengths were fabricated on z-cut LiNbO3 and tested at λ-1.3${\mu}{\textrm}{m}$. One device gad an exact coupling length for complete power transfer and two other devices had coupling lengths. It was confirmed that, for dc operation, experimental results agreed well with theoretical results.

• 한국자기학회지
• /
• 제10권5호
• /
• pp.203-209
• /
• 2000

Synthetic antiferromagnet CoFe/Ru/CoFe/FeMn을 사용하고 자유층으로 NiFe/CoFe 이중 층을 사용한 top스핀밸브 구조를 dc magnetron 방식으로 제조하여, 자유층과 구속층의 두께변화에 따른 자기적 특성과 interlayer coupling field티 변화를 조사하였다 Si/Ta(50 $\AA$)/NiFe(x $\AA$)/CoFe(y $\AA$)/Cu(26 $\AA$)/CoFe(30 $\AA$)/Ri(7 $\AA$)/CoFe(15 $\AA$)/FeMn(100 $\AA$)/Ta(50 $\AA$) top synthetic 스핀밸브 시료에서 자유층의 두께 감소에 따른 interlayer coupling field를 조사한 결과 interlayer coupling field가 증가하였으며, 이것은 Neel 모델에 의한 정자기 교환결합에 기인하는 것으로 설명하였다. Top synthetic 스핀 밸브에서 Cu에 인접한 자성층(Pl)과 FeMn에 인접한 자성층(P2) 두께 차이에 따른 interlayer coupling field 의 의존성을 조사한 결과 $t_{P1}$> $t^{P2}$ 일 경우 interlayer coupling field(층간 교환 결합력 세기)는 기존 스핀 밸브에서 적용한 Kools이 제시한 modified Nel 모델에 잘 부합되나, $t_{P1}$ $\leq$ $t_{P2}$ 인 경우 모델과 부합되지 않음으로 새로운 모델이 필요함을 확인하였다 Cu 두께에 변화에 따른 층간 교환 결합력 세기 의존성을 조사한 결과 Cu 두께를 32 $\AA$으로 증가시 층간 교환결합력 세기는 10 Oe 이하로 감소하였다.감소하였다.다.

• 전력전자학회논문지
• /
• 제27권2호
• /
• pp.157-164
• /
• 2022

This study proposes an enhanced quadruple-Active-Bridge (QAB) converter that can solve power coupling problems. By adopting a multiple winding transformer, the equivalent circuit of a conventional QAB converter has power couplings between arbitrary output ports. This coupling is an unintended power relationship that complicates the regulation of output voltage of the multiple ports. The proposed converter can carry out power decoupling by changing the arrangement of the coupling inductor. Power transfer equations for the proposed converter and its operating principles are analyzed in detail. The power coupling caused by the transformer's leakage inductance is verified by using a proposed coupling factor that presents the relationship between inductance ratio and coupling power. In addition, the decoupling power control performance of the proposed converter is verified by simulation and a 3 kW prototype converter.

• Journal of Power Electronics
• /
• 제7권3호
• /
• pp.191-202
• /
• 2007

This paper deals with pulse multiplication in zigzag connected autotransformer based 12-pulse AC-DC converters feeding vector controlled induction motor drives (VCIMD) for improving the power quality at the point of common coupling (PCC) without using a Zero-Sequence-Blocking-Transformer (ZSBT). The proposed 24-pulse AC-DC converter is based on the principle of DC ripple re-injection technique for pulse multiplication and harmonic mitigation. The design of the autotransformer is carried out for the proposed AC-DC converter and the effect of load variation on VCIMD is also studied to demonstrate the effectiveness of the proposed AC-DC converter. Test results from a laboratory developed prototype, along with simulated results, are presented to validate the design and model of the proposed 24-pulse AC-DC converter.