• 한국표면공학회지
• /
• 제32권2호
• /
• pp.93-99
• /
• 1999

Surface polymer layer formed on the silicon wafer during the oxide overetching using $C_4F_8$/ helicon wave plasmas and their characteristics were investigated using spectroscopic elipsometry, X-ray photoelectron spectroscopy, and secondary ion mass spectrometry. Overetch percentage and dc-self bias voltage were varied to investigate the effects on the characteristics of the polymers remaining on the overetched silicon surface. The increase of bias voltage from -80 volts to -120 volts increased the C/F ratio and carbon bondings such as C-C, $C-CF_x$/, and C-Si in the polymer while reducing the thickness of the polymer layer. However, the increase of the overetch percentage from 50% to 100% did not change the composition of the polymer layer and the carbon bondings in the polymer layer remained same even though it increased the polymer thickness. The polymer layer formed at the higher dc-self bias voltage was more difficult to be removed by the following various post-etch treatments compared to that formed at the longer overetch percentage.

• 한국진공학회지
• /
• 제6권2호
• /
• pp.136-142
• /
• 1997

An/n-GaAs(100) Schottky 장벽 diode를 제작하여 변조전압($V_{ac}$) 및 dc 바이어스 전 압($V_{bias}$) 변화에 따른 electroreflectance(ER)를 측정하였다. 관측된 Franz-Keldysh oscillation(FKO) 피크로부터 이 시료의 내부 전기장($E_i$)은 $5.76\times 10^{4}$V/cm였다. $V_{ac}$를 변화시 킴에 따라 ER신호의 모양은 변화가 없고, 진폭만 선형적으로 증가하였다. 순방향 및 역방향 의 $V_{bias}$변화에 따라 ER신호의 진폭은 감소하였으며, $V_{bias}$가 -5.0~0.6V로 증가함에 따라 Ei 는 $19.3\times 10^4\sim4.39\times10^4$V/cm로 감소하였다. 그리고 $V_{bias}$변화에 대한 $E_i^2$의 그래프로부터 built-in 전압(Vbi)은 0.70V였으며, 이 값은 $V_{bias}$변화에 따른 FKO피크의 진폭 관계 그래프 에서 얻은 결과와 잘 일치하였다. 또한 이 시료의 캐리어 농도(N)와 전위장벽($\Phi$)은 300K에 서 각각 $2.4\times 10^{16}\textrm{cm}^{-3}$와 0.78eV의 값을 얻었다.

• Transactions on Electrical and Electronic Materials
• /
• 제9권6호
• /
• pp.260-264
• /
• 2008

The operational characteristics of superconducting amplifier using vortex flux flow were analyzed from an equivalent circuit in which its current-voltage characteristics for the vortex motion in YBCO microbridge were reflected. For the analysis of operation as an amplifier, dc bias operational point for the superconducting amplifier is determined and then ac operational characteristics for the designed superconducting amplifier were investigated. The variation of transresistance, which describes the operational characteristics of superconducting amplifier, was estimated with respect to conditions of dc bias. The current and the voltage gains, which can be derived from the circuit for small signal analysis, were calculated at each operational point and compared with the results obtained from the numerical analysis for the small signal circuit. From our paper, the characteristics of amplification for superconducting flux flow transistor (SFFT) could be confirmed. The development of the superconducting amplifier applicable to various devices is expected.

• 전기학회논문지
• /
• 제67권3호
• /
• pp.383-390
• /
• 2018

Piezoelectric micro-machined ultrasonic transducers for highly directional speaker need DC bias voltage. Most existing power amplifiers are not suitable for use in highly directional transducers because they are based on AC. In addition, since the piezoelectric micro-machined ultrasonic transducer has a large capacitive reactance, the power efficiency of the power amplifier is very low. Thus this paper proposes a new high efficiency power amplifier with DC bias voltage. In addition, by designing a matching circuit to compensate the capacitive reactance of the micro-machined ultrasonic transducer, the power efficiency of the power amplifier increases. The operating characteristics of the proposed power amplifier was verified by an experimental prototype. The proposed power amplifier is expected to be widely used in designing and implementing other related power amplifiers.

• 제어로봇시스템학회논문지
• /
• 제13권4호
• /
• pp.315-319
• /
• 2007

A technique to model plasma processes was presented. This was accomplished by combining the backpropagation neural network (BPNN) and genetic algorithm (GA). Particularly, the GA was used to optimize five training factor effects by balancing the training and test errors. The technique was evaluated with the plasma etch data, characterized by a face-centered Box Wilson experiment. The etch outputs modeled include Al etch rate, AI selectivity, DC bias, and silica profile angle. Scanning electron microscope was used to quantify the etch outputs. For comparison, the etch outputs were modeled in a conventional fashion. GABPNN models demonstrated a considerable improvement of more than 25% for all etch outputs only but he DC bias. About 40% improvements were even achieved for the profile angle and AI etch rate. The improvements demonstrate that the presented technique is effective to improving BPNN prediction performance.

• Journal of Advanced Marine Engineering and Technology
• /
• 제41권2호
• /
• pp.146-149
• /
• 2017

Si clusters generated during the plasma chemical vapor deposition (CVD) process have a great influence on the quality of the fabricated films. In particular, in hydrogenated amorphous silicon thin films (a-Si:H) used for thin film solar cells, Si clusters are mainly responsible for light-induced degradation. In this study, we investigated the amount of clusters incorporated into thin films using a quartz crystal microbalance (QCM) and specially designed cluster eliminating filters, and investigated the effect of the DC grid mesh in preventing cluster incorporation. Experimental results showed that as the applied voltage of the grid mesh, which is placed between the electrode and the QCM, decreased, the number of clusters incorporated into the film decreased. This is due to the electrostatic force from the grid mesh bias, and this method is expected to contribute to the fabrication of high-quality thin films by preventing Si cluster incorporation.

• Journal of electromagnetic engineering and science
• /
• 제13권2호
• /
• pp.137-139
• /
• 2013

A compact metamaterial (MTM)-based tunable phase shifter consisting of four unit cells with a simple DC bias circuit has been designed at 2.4 GHz. The variable series capacitors and shunt inductors that are required to be loaded periodically onto a host transmission line are realized employing only chip variable capacitors (varactors). In addition, the proposed phase shifter requires only one DC bias source to control the varactors, with the matching condition of the MTM line automatically satisfied. The measured phase shifting range is $285.2^{\circ}$ (from $-74.2^{\circ}$ to $211^{\circ}$). The measured insertion loss is approximately 1.5 dB. The circuit/electromagnetic-simulated and measured results are in good agreement.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.540-542
• /
• 2009

Phosphorus doped ZnO (PZO) thin films were deposited on $SiO_2$/n-Si substrates using DC magnetron sputtering system varying oxygen partial pressures from 0 to 40 % under Ar atmosphere. The deposited films showed reduced n-type conductivity due to the compensating donor effects by phosphorus dopant. The bias-time stability shows relatively good stability over bias and time comparing to un-doped ZnO-based TFTs.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.195-198
• /
• 1999

A technique is investigated for achieving broadband properties by controlling the operation frequency of microstrip antennas. The control is achieved by applying DC bias to the microstrip antenna. Air gap antenna with PZT post is fabricated. by using in C-band. In the case of Air gap antenna, the variation of center frequency was about 16Mhz and the bandwidth was increased up to 123.3% at 15dB, 160.7% at 20dB than before applying DC bias respectively. The change property of frequency in air gap antenna is nearly the same the C-V property in PZT.

• 한국정보통신학회논문지
• /
• 제16권10호
• /
• pp.2237-2246
• /
• 2012

본 논문에서는 구강센서를 소형화하고 제조 원가를 낮추기 위해 구강센서에서 필요로 하는 바이어스 회로를 구강센서 칩 내부에서 만들어주었다. 제안된 DC-DC 변환기 회로는 기준전류 발생기(reference current generator) 회로의 IREF를 이용하여 전압 레귤레이터(voltage regulator)에 필요한 기준전류와 바이어스 전류를 각각 공급해준다. 이들 전류가 각각의 전압 레귤레이 회로에서 해당되는 기준전압을 생성하여 부궤환(negative feedback)에 의해 목표전압을 regulation하게 된다. 그리고 기준전류가 전류 복사비(current mirror ratio)에 의해 mirroring되어 정전류인 IB0/IB1을 공급해주고, VREF 전압을 공급해주도록 설계하였다. $0.18{\mu}m$ X-ray CMOS 이미지 센서 공정을 이용하여 설계된 구강센서의 DC-DC 변환기의 출력 전압의 평균 전압, ${\sigma}$와 $4{\sigma}$는 양호한 측정 결과를 얻었다. 그리고 line-pair pattern 영상은 blurring 없이 높은 해상도 특성을 보였으며, 좋은 구강 영상을 획득하였다.