• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.3
• /
• pp.45-54
• /
• 2014

In this paper, We have designed and fabricated 20 InP Gunn diodes using a current limiting epitaxial structure by MINT's optimized fabrication processes. We have also packaged the fabricated InP Gunn diodes using our optimized packaging method, and then designed and fabricated a W-band waveguide FTO to measure characteristics of the packaged InP Gunn diodes. The packaged InP Gunn diode have a ceramic ring, a Au plated stud and a lid, and a Maltese cross. The fabricated InP Gunn diodes have good RF characteristics such as high output powers (11.8~17 dBm) and limiting low currents (less than 400 mA) between 92.9 and 94.78 GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.7
• /
• pp.1347-1353
• /
• 2015

We implemented a 10 Gb/s 4-channel vertical cavity surface emission lasers (VCSEL) driver array in a $0.13{\mu}m$ CMOS process technology. To enhance high current resolution, power dissipation, and chip space area, digital APC/AMC with time division sensing technology is primarily adopted. The measured -3 dB frequency bandwidth is 9.2 GHz; the small signal gain is 10.5 dB; the current resolution is 0.01 mA/step, suitable for the wavelength operation up to 10 Gb/s over a wide temperature range. The proposed APC and AMC demonstrate 5 to 20 mA of bias current control and 5 to 20 mA of modulation current control. The whole chip consumes 371 mW of low power under the maximum modulation and bias currents. The active chip size is $3.71{\times}1.3mm^2$.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.487-488
• /
• 1995

Broadband Microwave Low Noise Amplifier(LNA) is designed. The matching method using the broadband BPF(BandPass Filter) is introduced in this paper. This method is that the filter having the same reflection coefficient of Microwave GaAs FET in the desired bandwidth is located on the input stage of FET. The Simulated results is obtained that the $S_{21}$ and noise figure in 2.5GHz$\sim$9GHz, band are 8.5dB $\pm$ 1.5dB, 2.5dB $\pm$ 0.3dB respectively.

• Proceedings of the KOSOMBE Conference
• /
• v.1996 no.11
• /
• pp.317-320
• /
• 1996

Electrogastrography(EGG) has been an attractive method for physiological and pathophysiological studies of the stomach and now is on the verge of becoming a new clinical tool in gastroenterology. In this study 4 channel EGG measurement system was constructed and running spectrum analysis was developed for 2D and 3D display of power spectrum with time and frequency. A wavelet multiresolution method was utilized for elimination of baseline drift and for filtering out noises.

• Proceedings of the KIEE Conference
• /
• 1998.07c
• /
• pp.943-945
• /
• 1998

This paper presents a method of modeling of DSTATCON (Distribution-line Static Condenser) for installation in a specific plant and analyze the effectiveness of the DSTATCON from the viewpoints of voltage regulation and harmonic mitigation in a distribution line. For the reliable modeling, detailed information on distribution system and loads is performed by field measurements. The DSTATCON has been modeled according to the control algorithm of real controller. The effectiveness of the DSTATCON installation is verified by simulation using EMTDC.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.335-337
• /
• 1993

Offset voltage and drift characteristics of operational amplifier are critical factor to precision AID conversion System. In this study, a method is suggested to design the programmable A/D conversion system which has high resolution and low drift characteristics. First, hardware was designed to reduce the offset voltage of integrator and comparator, and analog switches are connected to reduce the drift characteristics of operational amplifier. And then, a calibration software technique was performed to obtain the stable data from A/D converter. The main advantage of our method is high precision A/D converter can be constructed with low cost and high confidence. Therefore proposed method is expected to be used in the industrial field where a high precision measurement is required.

• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.450-452
• /
• 1993

In this study, a method is suggested to design the A/D conversion system which has high resolution to convert load cell signal. First, hardware was designed to reduce the offset voltage of integrator and comparator. And then, a calibration software technique was performed to obtain the stable data from A/D converter. The optimal parameters of each elements in the circuits was selected using the SPICE simulation. The main advantage of our method is high precision A/D converter can be constructed with low cost and high confidence. Therefore proposed method is expected to be used in the industrial field where a high precision measurement is required.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.109-110
• /
• 2006

Various parametric methods, Larson-Miller (L-M), Orr-Sherby-Dorn (O-S-D), Manson-Haferd (M-H) parameters, and minimum commitment method (MCM), were used to predict longer rupture time from short-term creep data. A number of the creep data were collected through literature surveys and experimental data produced in KAERI for predicting the creep type of type 316LN SS. Polynomial equations for predicting the creep life were obtained by the time-temperature parameters (TTP) and the MCM. standard error (SE) and standard error or mean (SEM) values were compared for the each method with temperatures. The TTP methods were good in the creep-life prediction, but the MCM was much superior to the TTP ones at $700^{\circ}C\;and\;750^{\circ}C$. The MCM was found to be lower in the SE values compared to the TTP methods

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.409-414
• /
• 2005

This study is based on the recent CISPR(International Special Committee on Radio Interference) research which is focused on the Radiated Emission test method above 1 GHz and explained "w"(Measurements dimension) for the antenna's $\theta_{3dB}$ characteristic. And expound the work in progress in the IEC Standard for the measurement methods and the limits above 1 GHz.

• Journal of Power System Engineering
• /
• v.2 no.3
• /
• pp.21-26
• /
• 1998

Numerical simulations for various fluid flows require enormous computing time during iterations. In order to solve this problem, several techniques have been proposed. A SOR method is one of the effective methods for solving elliptic equations. However, it is very difficult to find the optimum relaxation factor, the value of this factor for practical problems used to be estimated on the basis of expertise. In this paper, the implication of the relaxation factor are translated into fuzzy control rules on the basis of the expertise of numerical analysers, and fuzzy controller incorporated into a numerical algorithm. From two cases of study, Poisson equation and cavity flow problem, we confirmed the possibility of computational acceleration with fuzzy logic and qualitative reasoning in numerical simulations. Numerical experiments with the fuzzy controller resulted in generating a good performance.