• Geomechanics and Engineering
• /
• 제9권6호
• /
• pp.743-755
• /
• 2015

It is well known that the quality of sample significantly determines the accuracy of soil parameters for laboratory testing. Although sampling disturbance has been studied over the last few decades, the theoretical investigation of soil disturbance due to sampling penetration has been rarely reported. In this paper, an analytical solution for estimating the soil disturbance due to sampling penetration was presented using cavity expansion method. Analytical results in several cases reveal that the soil at different location along the sample centerline experiences distinct phases of strain during the process of sampling penetration. The magnitude of induced strain is dependent on the position of the soil element within the sampler and the sampler geometry expressed as diameter-thickness ratio D/t and length-diameter ratio L/D. Effects of sampler features on soil disturbance were also studied. It is found that the induced maximum strain decreases exponentially with increasing diameter-thickness ratio, indicating that the sampling disturbance will reduce with increasing diameter or decreasing wall thickness of sampler. It is also found that a large length-diameter ratio does not necessarily reduce the disturbance. An optimal length-diameter ratio is suggested for the further design of improved sampler in this study.

• Design & Manufacturing
• /
• 제15권4호
• /
• pp.51-56
• /
• 2021

Piercing is the process of shearing a circular hole in sheet metal, whose high shear force makes it difficult to secure the durability of tools. In addition, uneven clearance between tools due to poor alignment of the piercing punch causes accelerated die wear and breakage of the tool. This study reviewed the feasibility of in-situ determining alignment failure during the piercing process by analyzing the signal deviation of a bolt-type piezo sensor installed inside the tool whose alignment level was controlled. Finite element analysis was performed to select the optimal sensor location on the piercing tool for sensitive detection of process signals. A well-aligned piercing process results in uniform deformation in the circumferential direction, and shearing is completed at a stroke similar to the sheet thickness. Afterward, a sharp decrease in shear load is observed. The misaligned piecing punch leads to a gradual decrease in the load after the maximum shear load. This gradual decrease is due to the progressive shear deformation that proceeds in the circumferential direction after the initial crack occurs at the narrow clearance site. Therefore, analyzing the stroke at which the maximum shear load occurs and the load reduction rate after that could detect the misalignment of the piercing punch in real-time.

• ETRI Journal
• /
• 제46권3호
• /
• pp.404-412
• /
• 2024

We propose a method for increasing the bandwidth of a substrate-integrated-waveguide (SIW) cavity-backed antenna with taper-based micro-strip SIW transition feeding. For radio transmission, a circular slot is etched on top of the SIW cavity. For optimal antenna design, the slot is etched slightly away from the cavity center to generate circularly polarized waves. Simulations show a wide axial ratio bandwidth of 7.860% between 11.02 GHz and 11.806 GHz. Experimental results confirm a similar wide axial ratio bandwidth of 4.9% between 10.8 GHz and 11.35 GHz. An SIW feed from an inductive window excites the radiating circular slot, resulting in a simulated wide impedance range of 1.548 GHz (10.338 GHz-11.886 GHz) and bandwidth of 13.93%. Experimental results show a wide impedance of 2.08 GHz (10.2 GHz-12.08 GHz) and bandwidth of 18.84%. The SIW cavity-backed antenna creates a unidirectional pattern, leading to gains of 6.61 dBi and 7.594 dBi in simulations and experiments, respectively. The proposed antenna was fabricated on a Rogers RT/Duroid 5880 substrate, and the reflection coefficient, radiation patterns, and gains were tested and compared using a computer simulator. The developed broadband antenna seems suitable for X-band applications.

• 한국전산구조공학회논문집
• /
• 제35권4호
• /
• pp.227-233
• /
• 2022

3D 프린팅은 다수의 레이어(layer)를 적층하여 물체를 제작하는 기법으로, 복잡한 형상을 가지는 물체를 비교적 쉽게 제작할 수 있다. 이를 건설 산업에 접목한 3D 콘크리트 프린팅(3D concrete printing)은 콘크리트 타설 시 거푸집을 사용하지 않으며, 비교적 적은 작업량과 인력이 요구되므로 경제적인 시공이 가능하나, 출력된 3D 프린팅 콘크리트는 일반 콘크리트 대비 다소 낮은 강도가 예상된다. 따라서, 본 연구에서는 3D 프린팅 콘크리트 시편의 물성을 분석하였다. 3D 프린팅 콘크리트 시편 출력을 위해 Ultimaker Cura 소프트웨어로 형상 및 출력 경로를 설계하고, 이를 바탕으로 3D 프린터를 제어하는 G-code를 생성하였다. 연구에서 사용된 3D 프린터의 출력 성능과 콘크리트의 적층성, 유동성 등을 고려하여 최적의 배합비를 선정하였고, 시편 출력에 활용하였다. 시편 출력 시 동일한 치수를 가지는 몰드 시편을 함께 제작하여 비교·분석에 사용하였다. 각 시편의 물성은 휨강도 시험과 압축강도 시험을 통해 각각의 강도를 측정하였고, 비교·분석하여 3D 프린팅 콘크리트 시편의 물성을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.139-142
• /
• 2007

This study focuses on the manufacturing process of a magnesium alloy impeller used for the fuel cell car using the hot forging technology. The impeller has the very complicated shape with sharply curved blade and thus generally produced by mechanical machining or casting process. However, since these technologies give the high manufacturing cost or poor mechanical properties, the forging technology is required to make the high-quality impeller with the lower manufacturing cost. In order for production of the impeller by forging technology, the parametric studies using finite element analyses were carried out to find the optimal perform shape of impeller made of magnesium alloy AZ 31 and finally die design was proposed based on the simulation results.

• Journal of Electrical Engineering and Technology
• /
• 제1권2호
• /
• pp.200-210
• /
• 2006

This paper proposes the motion generation method in which the movement of the 3-links leg subsystem in constrained to slider-link and a singular posture can be easily avoided. This method is the realization of jumping control moving in a vertical direction, which mimics a cat's behavior. To consider the movement from the point of the constraint mechanical system, a robotics system for realizing the motion will change its configuration according to the position. The effectiveness of the proposed scheme is illustrated by simulation and experimental results.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.693-696
• /
• 2011

The SRM (Switched Reluctance Motor) is composed of silicon steel plates where the rotor structure is simple and laminated without coil winding or permanent magnet, making it mechanically robust and its maintenance and repair excellent. Applying SRM as traction motor for railway vehicle is given consideration because of its ruggedness capability in severe loading condition and its compact structure. Optimal design of SRM is needed to reduce torque ripple to apply SRM for railway traction drive because SRM has high torque ripple. In this paper, switched reluctance motor with three different stator pole shapes is taken for magnetic analysis using 3d finite element method to apply SRM as traction drive for railway vehicle. It is observed that the model 3 added Tooth Tang Depth and Slot Round to stator shape gives the improved inductance and torque characteristic.

• 한국정밀공학회지
• /
• 제33권7호
• /
• pp.601-606
• /
• 2016

In this paper, an energy harvester is developed that has advantages regarding piezoelectric noise minimization, mass production, and an easily available environmental energy source, electromagnetic induction, as well as low-frequency bandwidth and high amplitude. A process for fabricating a three-dimensional multilayered planar coil using micro-electro-mechanical systems (MEMS) on a flexible printed circuit board FPCB is introduced. Optimal shape and size were calculated via internal resistance and inductance, and a prototype was fabricated through the MEMS procedure while considering the possibility of mass production. Although the internal resistance matched the designed value, the electromotive force generated did not reach the intended amount. The main reason for the decrease in efficiency was the low area of coil outskirt exposed to the magnetic field while there was relative motion between the magnet and the coil.

• International Journal of Automotive Technology
• /
• 제3권4호
• /
• pp.157-163
• /
• 2002

It is well recognized that the ultrasonic method is one of the most common and reliable nondestructive testing (NDT) methods for the quantitative estimation of defects in welded structures. However, NDT techniques applying for adhesively bonded joints have not been clearly established yet. In this paper, the detection of interface crack by the ultrasonic method was applied for the measurement of interfacial crack length in the adhesively bonded joints of double-cantilever beam (DCB). An optimal condition of transmission coefficients and experimental accuracy by the ultrasonic method in the adhesively bonded joints have been investigated and discussed. The experimental values are in good agreement with the computed results by boundary element method (BEM) and Ripling's equation.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 추계학술대회 논문집
• /
• pp.156-159
• /
• 2001

Recently, side scan sonar system has been developed and operated to survey cable laying, sunken bodies, geometry of sea bottom and so on. It uses the acoustic signals, which are emitted from two transducer arrays, left and right sides, to get geometric information of the specified area. This system consists of transceiver board, towed body, deck unit and GPS receiver. The transceiver board, nested in a watertight canister, controls the transmitting and receiving of the acoustic pulses from transducer arrays. After receiving the scattered signals, it processes BP(Band Pass) filtering, AGC(Automatic Gain Control), TVG(Time Varying Gain) and Heterodyne. The deck init has the signal processing part, A/D converter, power supplier, and real-time monitoring part. The towed body has been designed to satisfy the optimal hydrodynamic behavior during towing, In this paper, brief introductions on the design theory of transceiving part and some results from the field which have been operated recently will be introduced.