• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.93-94
• /
• 2009

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.750-751
• /
• 2008

본 논문은 컨버터용 변압기의 여자전류 해석을 통해 DC 성분 유입시 자속밀도-여자전류 곡선 그래프를 도출하여 철심포화 여부를 확인하며, 철심 공극에 의해 발생되는 누설자속(Leakage Flux)으로 인한 철구조물(Lock Plate)의 와전류 손실을 계산하였다. 변압기 해석을 위해 상용 해석 소프트웨어인 Maxwell 3D를 이용하였고, 철심의 비선형성을 고려하여 해석하였다.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.149-151
• /
• 2006

This paper shows the characteristic analysis of single-phase LSPM(Line Start Permanent Magnet) synchronous motor considering overhang structure. To obtain the dynamic and steady performance of the motor, the D-Q equivalent circuit is used and the circuit parameters are extracted by 3D FEM. The performance of the model with overhang is compared with conventional model without overhang on the condition that both models have the same volume of the permanent magnet.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.904-905
• /
• 2011

본 논문에서는 기존의 EPS(Electric Power Steering) 시스템에 IPMSM을 적용하고 속도 및 위치를 검출하기 위하여 Magnetic Position Sensor를 사용하였다. 이�� Magnetic Position Sensor의 신호는 정현파의 출력을 갖지만 고조파의 성분으로 인하여서 파형이 왜곡되고 이러한 파형의 왜곡으로 인해 위치 검출의 오차를 갖게 된다. 본 논문에서는 이러한 오차를 줄이기 위하여 다구찌 기법과 3차원 유한요소법(3D FEM)을 사용하여 고조파를 저감시킬 수 있도록 여러 변수를 변화하여서 최적의 설계를 통하여 실제 실제 센서 출력과 비교하여 자동차 산업 전반에 기여 하고자 한다.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.369-374
• /
• 2011

An induction motor operated with high voltage source generally generates high current in starting mode and has a long transient time after being started. This large and sustaining starting current causes the end windings of the stator to have excessive electromagnetic force. This force is the source of vibration and has a negative and serious influence on the insulation of end windings. Therefore, designing the end winding part with an appropriate support system is needed. To design the support ring enclosing the end windings, we analyze the distribution of electromagnetic force on the end windings by applying the Biot-Savart's law and the 3D finite element method (FEM), and comparing two simulation methods. Finally, we verify the safety of the support structure of the end winding part using stress analysis, which is analyzed with the electromagnetic forces from the 3D FEM simulation.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.153-155
• /
• 1994

Electric machines such as motors which have moving parts are desgined for producing mechanical force or torque. The accurate calculation of electromagnetic force and torque is important in the design these machines, Electromagnetic force calculation method using the results of Finite Element Method(FEM) has been presented variously in 2-D problems. Typically the Maxwell's Stress Tensor method and the method of virtual work are used. In the problems including current source, magnetic vector potentials(MVP) have mostly been used as an unknown variables for field analysis by numerical method; e, g. FEM. This paper, thus, introduces both methods using MVP in 3-D case. To verify the usefulness of presented methods, a solenoid model is chosen and analyzed by 3-D and axisymmetrical FEM. In each case, the calculated force are tabulated for several mesh schemes.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.238-240
• /
• 2000

We designed the prototype of electromagnetic wobble motor which could be applied to ultrasonic catheter in the before study. So, In this paper we perform 3D FEM of the designed prototype model with the computer analysis tool(Magnet 6.4). Therefore we prove the characteristics and theorems of the wobble motor with 3D FEM.

• Journal of the Korea Concrete Institute
• /
• v.26 no.1
• /
• pp.57-62
• /
• 2014

In this study, the vertical pipe cooling method was developed to propose the pipe cooling method suited for the vertically long mass concrete structures. FEM (finite element method) analysis was carried out to investigate the validity of the vertical pipe cooling method, and the temperature, the behavior of tensile stress of concrete and the crack index were investigated. In result, it was confirmed that the vertical pipe cooling method was effective in the thermal cracking control of mass concrete member.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.9
• /
• pp.493-498
• /
• 2002

Double-side linear pulse motor(DSLPM) has more advantages than single-side linear pulse motor because noise and vibration can be considerably decreased by countervailing the normal forces, which is generated between two stators and mover. However, DSLPM has more complicated magnetic flux path and layout of stator pole toot/mover tooth rather than single-side linear pulse motor In this paper, DSLPM is designed and fabricated by considering the air gap magnetic density, shape of tooth and slot. In order to verify the characteristics of DSLPM, the air gap magnetic flux density is analyzed by 2D FEM and the magnetic flux path is analyzed by 3D FEM. Also the static thrust forces is obtained with the analyzed results.

• Journal of the Korean Society of Radiology
• /
• v.15 no.5
• /
• pp.585-590
• /
• 2021

Wrist braces are being used for patients with wrist trauma. Recently, many studies have been conducted to manufacture custom wrist braces using 3D printing technology. Such 3D printing customized orthosis has the advantage of reflecting various factors such as reflecting different shapes for each individual and securing breathability. In this paper, the stress on the orthosis by the number and position of Velcro bands that should be considered when manufacturing a 3D printing custom wrist brace was analyzed. For customized orthosis, 3D modeling of the bone and skin regions was performed using an automatic design software (Reconeasy 3D, Seeann Solution) based on CT images. Based on the 3D skin area, a wrist orthosis design was applied to suit each treatment purpose. And, for the elasticity of the brace, a wrist brace was manufactured with an FDM-type 3D printer using TPU material. To evaluate the effectiveness according to the number and position of the Velcro band of the custom 3D printed wrist brace, the stress distribution of the brace was analyzed by the finite element method (FEM). Through the finite element analysis of the wrist orthosis performed in this study, the stress distribution of the orthosis was confirmed, and the number and position of the orthosis production and Velcro bands could be confirmed. These experimental results will help provide quality treatment to patients.