• Journal of Electrical Engineering and Technology
• /
• v.6 no.5
• /
• pp.618-625
• /
• 2011

This paper presents a double excited three degree-of-freedom (3DOF) motor. The proposed 3DOF motor is designed with a laminated structure, making it easy to manufacture. In addition, it has windings on the stator and rotor, and does not require an expensive permanent magnet. We explain the structure, principle of motion, and design of the proposed motor, and perform an analysis of the static characteristics using the two- and three-dimensional finite element methods (3D FEM). The feasibility of 3D FEM analysis is confirmed by comparing the 3D FEM analysis and experimental results for the rolling and pitching motion. We also confirm the occurrence of holding torque in every motion.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1306-1308
• /
• 2005

The characteristic of line start permanent magnet(LSPM) motor with overhang structure is analyzed using 3dimensional finite element method(3D FEM). We propose the appropriate overhang length by considering the magnetic flux distribution according to changing overhang length and manufacturing process. 3D FEM analysis is inevitable because the increase of the total flux cannot be appropriately considered in 2D FEM. In equal model specification total flux is recalculated at 3D FEM, because of considering lamination length. This paper compares the characteristic of Back-emf with and without overhang by permanent magnet that has identical volume.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.911-913
• /
• 2004

This paper presents characteristic analysis of claw-pole type generator. The analysis is performed using 2D equivalent model by 2D FEM. 3D FEM is used to check whether 2D equivalent model reflects the magnetic characteristics of the actual machine. Initially, 2D equivalent model of the claw-pole type generator is designed only by 3D geometry. Using 2D equivalent model, back emf characteristics are estimated and compared to measurements. The analysis results agree with measurements well and take less time comparing to 3D FEM.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.12
• /
• pp.2605-2614
• /
• 2002

This paper describes an analysis method based on the experimental parameter for the 0.9kW starter motor of vehicle with permanent magnet and pole core, and analyzed the influence by the effect of pole core of starting motor by using the 2D-FEM analysis technique to reflect the structural characteristic of 3D. A starter motor consists mainly of armature, yoke and permanent magnet with the pole core. Additionally, there is different the axial length of each part. Therefore, the effective of analysis method is needed to improve the characteristic of it. This paper approached the 2D-FEM analysis estimated by the 3D-EMCN(Three Dimensional Equivalent Magnetic Circuit Network) instead of the 3D-FEM analysis to minimize parameters. As a result, this paper is proposed the validity of 2D-FEM analysis and obtained reasonable results for improving a performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.67-72
• /
• 2012

Novel Front End Module(FEM) with improved pedestrian protection is very important to reduce the severity of pedestrian injury. The FEM needs to have enough space from hood to absorb the energy from any pedestrian collision. In this study, the cooling performance of the FEM to cool the engine was investigated under 25% height reduction. The results indicated that the cooling performance analysis was about 86% level compared to that of the conventional FEM. Also, good qualitative agreement between CFD predictions and experimental measurements was found. This FEM needs the cooling performance enhancement for changed air flow path at the frontal part of vehicle. Therefore, we showed an improved performance using air guide setup and shape modification under the high load condition.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1835-1837
• /
• 2004

The UHF electromagnetic waves excited by PD pulses propagate along the GIS busbar not only TEM mode, but also TE and TM mode. Generally the waves detected by the UHF sensors are those of high order modes and such waves can only propagate the higher than cut-off frequency. In this paper, computed cut-off frequency of 362[kV] GIS by each modes and simulated electromagnetic field of each propagation modes by FEM(Finite Element Method) program. Frequency band of each TEmn/TMmn modes were determinated by simulation results and were discussed optimal position of UHF sensor from this results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.941-944
• /
• 2015

In this paper study for VSAT(very small aperture terminal) LNB(low noise block). ship LNB was demanded high stability and low noise figure. We designed FEM(Front-End Module) that was operated multi-band. FEM designed was constructed in a multi-band low noise receiver amplifier, a frequency converter, IF amplifier, Voltage Control Oscillator signal generating circuit four circuit using. To convert the multi-band 2.05GHz band, it generates four local oscillator signals, the four(band1, band2, band3, band4) designed to output an IF signal developed conversion apparatus, the conversion gain 64dB, noise figure 1dB or less, output P1dB 15dBm or more, phase noise showed -73dBc@100Hz.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.11 no.2
• /
• pp.61-67
• /
• 2015

3D FEM modeling based on 3D CAD data has been performed to evaluate the efficiency of CP system in a real operating nuclear power plant. The results of it successfully produced sophisticated profiles of electrolytic potential and current distributions in the soil of an interested area. This technology is expected to be a breakthrough for detection technology of damages on buried pipes when it comes into combining with a brand of area potential earth current (APEC) and ground penetrated radar (GPR) technologies. 2D current distribution and 2D current vectors on the earth surface from the APEC survey will be used as boundary conditions with exact 3D geometry data resulting in visualization of locations and extents of corrosion damages on the buried pipes in nuclear power plants.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.931-932
• /
• 2013

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.978-983
• /
• 2009

This paper analyzed longitudinal end effect occurred in linear induction motor by using I-d direct solution and its result is verified by 2-d Finite Element Method(FEM). Longitudinal end effect of linear induction motor caused by magnetic discontinuity in primary core and electric discontinuity in armature winding has been investigated by many researchers. In this paper, 1-d direct solution and boundary conditions proposed by Yamamura and Nasar is used to analyze end effect of linear induction motor and its solution is verified by 2-d FEM.