• 오토저널
• /
• 제7권1호
• /
• pp.55-62
• /
• 1985

This study modeled in axisymmetric solid elements and analyzed the neighbourhood of the contact surface zone between liner and block in a diesel engine. The results of finite element analysis show that this model is deformed by bolt jointed load and pressure load and that stresses can vary much due to major dimensional changes in the joint area. Guidelines have been developed for selecting fillet radii and for the width of the contact area between liner and block.

• Journal of Ship and Ocean Technology
• /
• 제8권4호
• /
• pp.34-44
• /
• 2004

Engine visualization is the most important process to develop the new engine. But this step has a major difficulty that is almost impossible to access the engine on running. Therefore, little indication from the experimental and analytical results has been so far. This work has conducted the important issue of developing a quartz liner. And it has given us good qualitative and quantitative results of temperature and stress fields in the quartz cylinder by considering forced convection of outside quartz liner, thickness of the quartz liner and preheating effect to operate quartz engine safely.

• 항공우주기술
• /
• 제2권2호
• /
• pp.124-132
• /
• 2003

본 논문에서는 "KSR-III 복합재 가압탱크“에 대한 구조 설계/제작 과정을 기술하였다. 복합재 가압탱크는 라이너 위에 복합재가 덮어 씌워진 형태이다. 하중을 부담하지 않는 라이너는 AI 6061-0로 만들어 졌으며, 라이너는 헬륨가스 기밀만을 담당하였다. 복합재 탱크는 라이너 위에 T700/Epoxy로 와인딩 하였다. 알루미늄 라이너가 얇았기 때문에 다단계 경화 공정이 필라멘트 와인딩 기법에 적용되었다. 다단계 경화 공정은 라이너의 실린더가 원형 형상을 잃지 않게 하였다. 보스부의 체결력은 보스링에 의하여 카본섬유로 분산되었다. 또한 보스링은 보스부의 국부적 변형을 막았다.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.147-158
• /
• 1997

This paper presents the analysis technique and procedure of main engine components-cylinder block, cylinder liners, gasket and cylinder head-using the finite element method, which aims to assess mainly the potential of lower oil consumption in a view point of engine design and to decide subsequently the accuracy of engine design which was done. The F.E. model of an engine section consisting of one whole cylinder and two adjacent half cylinders is used, whereby the crankcase is cut off at the block bottom deck. By means of a 3-dimensional F.E. model-including cylinder block, liners, gasket, cylinder head, bolts and valve seat rings as separate parts a linear analysis of deformations and stresses was performed for three different loading conditions;assembly, thermal and gas loads. For the analysis of thermal boundary conditions also the temperature field had to be evaluated in a subsequent step.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.232-239
• /
• 1999

Generally quantity of supply oil for piston ring lubrication in an internal combustion engine may be insufficient to fill the entire volume formed in the clearance between piston ring and cylinder liner. Thus oil starvation condition should be considered for the analysis of piston ring lubrication. In order to reasonably estimate amount of oil left on the cylinder liner, adequate boundary condition should be adapted for the analysis of ring pack lubrication. In this analysis of ring pack lubrication of an internal combustion engine, oil starvation and open-end boundary conditions are considered at inlet and outlet of piston rings. It is revealed that piston rings are operated under oil starvation in most operating cycle and the result with these conditions are quite different from that with fully-flooded assumption.

• 한국자동차공학회논문집
• /
• 제7권9호
• /
• pp.165-171
• /
• 1999

An oil layer fuel absorption /desorption modeling was developed. Multi-component fuel model has showed more reasonable condition than single component model. Henry's constant which is related to solubility is the most important variable in the oil layer absorption/desorption mechanism. The oil segments close to the top of the cylinder liner have more significant contribution to the fuel absorption and desorption process than other oil segments. At the warmed-up condition, the effect of the engine speed on the precent fuel absorbed/desorbed is minimal. But at low il film temperature, percent of fuel abosrbed/desorbed is decreased with increasing the engine speed because of low value of molecular diffusion coefficient of fuel. The amount of fuel trapped in the piston crevice is from 2 to 2.3 times larger than that of fuel in the oil fim. However, fuel form oil film slowly desorbs into the combustion chamber compared with fuel from the piston crevices when the engines is cold.

• Journal of Mechanical Science and Technology
• /
• 제14권9호
• /
• pp.928-934
• /
• 2000

This paper describes a method developed for the simulation of ring pack lubrication characteristic in an internal combustion engine. In general, the quantity of oil supply for piston ring lubrication may be insufficient in filling the entire volume formed at the interference between the piston ring and the cylinder liner. Thus the oil starvation condition should be considered in analyzing piston ring lubrication. In order to reasonably estimate the amount of oil left over on the cylinder liner, the flow rate at the posterior portion of the interface should be calculated with an adequate boundary condition that confirms flow continuity condition. In this analysis, oil starvation and open-end boundary conditions are considered at the inlet and outlet of the piston rings. The lubrication characteristic of each piston ring is obtained by an iterative method with sequential steps. It is revealed that piston rings are operated under oil starvation in most operating cycles and the result under these conditions are quite different from that with the fully-flooded assumption.

• Tribology and Lubricants
• /
• 제15권3호
• /
• pp.233-239
• /
• 1999

Generally quantity of supply oil for piston ring lubrication in an internal combustion engine may be insufficient to fill the entire volume formed in the clearance between piston ring and cylinder liner. Thus oil starvation condition should be considered for the analysis of piston ring lubrication. In order to reasonably estimate amount of oil left on the cylinder liner, adequate boundary condition should be adapted for the analysis of ring pack lubrication. In this analysis of ring pack lubrication of an internal combustion engine, oil starvation and open-end boundary conditions are considered at inlet and outlet of piston rings. It is revealed that piston rings are operated under oil starvation in most operating cycle and the result with these conditions are quite different from that with fully-flooded assumption.

• 동력기계공학회지
• /
• 제16권6호
• /
• pp.11-18
• /
• 2012

대형 상용 엔진에서 발생하는 유효 도시 마력의 약 4~15%는 마찰 손실을 통해서 사라지며 마찰 손실 중 약 40~55%는 엔진 실린더와 피스톤 사이의 마찰에 의하여 발생하여, 엔진 전체에서 발생하는 마찰 손실 중 가장 많은 부분을 차지하고 있다. 이 연구에서는 엔진 실린더 라이너의 온도 분포 개선을 통해 라이너를 따라 유막을 형성하고 있는 윤활유의 적정 점성을 유지시키는 방법을 제시하고자 한다. 피스톤-라이너에서 발생하는 마찰 특성은 피스톤의 행정 위치에 따라서 접촉 마찰과 유막에 의한 마찰로 구분되며 이에 따라 요구되는 윤활유의 점성 특성 또한 달라진다. 먼저 해석 모델을 통하여 실린더 라이너 내부 온도 분포 특성을 확인한 후 피스톤 마찰 특성을 고려한 적정 온도 분포를 고찰하며 실린더 라이너에 열저항 코팅을 통해서 이를 구현하였다. 또한 실린더-피스톤 간의 마찰/윤활 해석을 통하여 열저항 코팅의 마찰 개선효과를 확인하였다.

• 대한기계학회논문집A
• /
• 제27권1호
• /
• pp.88-93
• /
• 2003

The aim of this paper is to investigate the friction characteristics of piston assembly, which composed of ring pack and piston skirt. The friction force of piston assembly was measured by using the movable liner in the single cylinder engine, and the various parameters were tested. The friction force was suddenly increased at the expansion stroke due to higher cylinder pressure. The viscous friction was dominant at the mid stroke, but the boundary friction was dominant at the top and bottom dead centers. Through the experiment, we could validate previous theoretical study, and confirm that th e radial clearance and ring tension were very effective to reduce friction loss of piston assembly.