• 한국기계가공학회지
• /
• 제10권6호
• /
• pp.115-121
• /
• 2011

This study is about comparison of tangental entry type cyclone dust collector with axial vane type cyclone dust collector. Cut diameter and dust collection efficiency of both collector was compared by theory and experiment. Cut diameter was calculated by an quasi-empirical formula by Lapple and Shepherd. Measurement of cut diameter was conducted by particle counter through dust generator. As the result, cut diameter obtained by experiment was a little larger than that by theory. But the error is within $0.5{\mu}m$ in both type of collector, so it could be confirmed that theoretical value and experimental value were almost identical. And, as flow rate increased, dust collection efficiency was increased. Also axial vane type showed higher dust collection efficiency than tangental entry type. Therefore, it can be said that axial vane type cyclone dust collector has higher performance than the other.

• 한국산업융합학회 논문집
• /
• 제23권1호
• /
• pp.101-106
• /
• 2020

Along with dust collection efficiency, pressure loss is a very important cyclone operation factor. A severe rise in pressure loss causes the problem of cost. To solve the problem, the method connecting axial-vane type cyclones in parallel is suggested recently. The axial vane type cyclone dust collector applied in this study is a small portable type. Multiple cyclones are installed in a round type. The basic performance test on the axial vane type cyclone dust collector was conducted. As a result, the cut size reduced along with a rise in the wind velocity of the cyclone dust collector inlet. According to the test on dust collection efficiency, the effect of dust collection began to appear in the range of 3㎛ and dust collection efficiency was greatly improved at 5 ㎛. The noise of the cyclone dust collector well met the fan sound power level of KSB 6361.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2013년도 추계학술대회
• /
• pp.911-913
• /
• 2013

본 논문에서는 선박의 외벽 청소용으로 사용되는 연마장비에 사이클론 집진방식을 채용한 연마장비를 개발을 위한 최적화된 설계를 위한 기본적인 메카니즘과 설계를 소개하고자 한다. 사이클론 방식은 공기의 유입 및 유출 속도 및 압력에 따른 미립자 등을 분리하는 기능을 하게 되는데 본 연구에서는 이러한 연마장비설계를 위한 사이클론 집진기의 효율과 압력, 유입 공기속도에 따른 설계방법을 소개하고 일부 실험결과를 제시하도록 한다.

• 한국입자에어로졸학회지
• /
• 제10권4호
• /
• pp.155-162
• /
• 2014

The internal temperature will change depending on operation conditions and material of cyclone dust collector. This study compares the results of collection efficiency and temperature distribution on the different heat flux at wall of dust collector. The previous researcher's experiment results were used to confirm the reliability of CFD(Computational Fluid Dynamics) model. Based on this verified CFD model, we extended the analysis on the cyclone dust collectors. In CFD study, we used RNG k-epsilon model for analysis of turbulence flow, fluid is air, the velocity at inlet is 10 m/s, the temperature of air is $600^{\circ}C$. Because of the difference of outer vortex and inner vortex temperature, the collection efficiency will reduce with the increase of heat flux, showed the highest collection efficiency at heat insulation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.891-892
• /
• 2010

• 한국입자에어로졸학회지
• /
• 제11권2호
• /
• pp.47-55
• /
• 2015

This study compares the results of collection efficiency of difference gas temperature in cyclone dust collector. The previous researcher's experiment results were used to confirm the reliability of CFD(Computational Fluid Dynamics) model. Based on this verified CFD model, we extended the analysis on the cyclone dust collectors. In CFD study, we used RNG k-epsilon model for analysis of turbulence flow, fluid is air, the velocity at inlet is 10 m/s, the temperature of air is $20^{\circ}C$, $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $600^{\circ}C$ and $1000^{\circ}C$. As the temperature decreases, the average velocity of outer vortex and collection efficiency is increased, showed the highest collection efficiency at $20^{\circ}C$. It can be inferred smooth flow in cyclone dust collector is difficult because air viscosity increases as temperature increases. The power required at $1000^{\circ}C$ is almost 18 times greater than that of $20^{\circ}C$ to get the similar collection efficiency.

• Journal of Biosystems Engineering
• /
• 제36권3호
• /
• pp.204-210
• /
• 2011

This study developed the cyclone conveying system using roughage cutter for the round bale reported in the previous papers. Performance tests were conducted whether it can easily separate dust from roughage such as rice straws and it can transport roughages from cutter to TMR mixer. In addition, the airflow patterns in the cyclone conveying system were investigated using CFD code (FLUENT 6.2) for various velocities of dust collection fan. The cyclone conveying system was designed based on dried rice straws with a diameter of 1,340 mm, a cylinder length of 1,220 mm, a cone length of 850 mm and the current velocity of the dust collection fan was 15~20 m/s. It was found that transporting of roughage from cutter to TMR mixer and the separation of dust were satisfactory, and the dust removal rate of rice straws was around 31.9%. CFD analysis showed that, at the blowing fan velocity of 11.6 m/s, the airflow velocity inside the dust collector increased as velocity of the dust collection fan increased, but the airflow patterns inside the dust collector were all much the same.

• 한국산학기술학회논문지
• /
• 제20권12호
• /
• pp.519-524
• /
• 2019

본 연구에서는 대풍량 곡물건조기에 사용되는 수평형 집진기의 집진효율 향상과 최적화를 위한 연구의 선행과정으로 Computational Fluid Dynamics(CFD)를 이용하여 집진기 내부의 유동 특성 분석과 원뿔형 허브의 각 변화가 집진기의 집진성능에 미치는 영향을 해석하였다. 최근 집진기 입구에 원뿔형 허브와 고정 베인을 설치하여 선회유동(Swirl Flow)을 발생시켜 이물질을 공기와 분리시키는 수평형 사이클론 집진기(Horizontal type Cyclone Dust collector)가 개발되었다. 이 집진기는 크기가 비교적 작고 설치가 용이하고 비교적 배압이 낮아 추가 동력을 필요로 하지 않으며 베인의 선회력을 이용하기 때문에 대풍량 배습용 송풍기에도 적용할 수 있는 장점을 가지고 있다. 그러나 수평형 집진기 형상으로 인해 발생하는 집진기 내부의 배압 문제와 분진 퇴적 문제를 해결하기 위해서 3차원 유동해석을 이용하여 집진기 내부 형상 변화에 따른 유동 특성에 관한 연구를 진행하였다. 실제 곡물건조기에 적용 가능한 수평형 집진기 설계를 위한 기초 자료를 제공하였으며, 향후 연구 예정인 고정 베인 설계, 주분리관 및 중간분리관의 설계에 적용하고자 한다.

• 한국산업융합학회 논문집
• /
• 제21권3호
• /
• pp.133-139
• /
• 2018

Precipitator is the most widespread device used to separate dust particles from the exhaust gas. In the shipyard, welding umbrellas, spark protection covers, and ventilators are not purchased and used for the work place to capture the flames and high temperature metal dust generated during the gardening process. In particular, a thorough analysis of design factors, such as capture rate, collection capacity calculation, filter speed, and materials selection, is required since spatial constraints are followed by structures, etc. In this study, conceived to address problems such as this cyclone and filtration filter system that combines all-in-one gausing collector prototype. Assessed through interpretation through the validity of the design and reliability.

• 한국대기환경학회지
• /
• 제12권1호
• /
• pp.43-53
• /
• 1996

Numerical simulation was performed for the 3-dimensional flow filed of gas and particle phase for cyclone dust collector. FVM(Finite Volume Method) was employed for gas phase. The flow was solved suing the k-.varepsilon. epsilon turbulence model. The particle exit at the bottom of the cone was treated as a solid wall in this model because the gas flow through the effective dust exit is usually insignificant. The major parameters considered in this study was vortex finder diameter, effective dust exit diameterm vortex finder length, inlet type for dimension performance. Particle trajectory calculations were made for three different, particle sizes of 1, 25 and 50 .mu.m. The results obtained from this study give some physical insight of dust particle collection mechanism together with the indication of the collection efficiency. The simulation results were in generally good agreement with empirical knowledge. The application of this kind of computer program looks promising as a potential tool for the design of cyclone and determination of optimum operating condition.