• Advances in materials Research
• /
• 제5권3호
• /
• pp.193-203
• /
• 2016

Compared to metal-to-metal tribology, polymer tribology presents further complexity as it is more prone to be influenced by operating conditions. Over the past two decades, progress in the field of wear of polymers has led to the establishment of more refined wear mechanisms. The current paper establishes the link between different load parameters and the wear rate of polymers, based on experimental investigations. A pin-on-plate reciprocating tribometer was used to examine the wear behaviour of polyamide sliding against a steel counterface, under constant and fluctuating loads, in dry conditions. In addition, the influence of controlled imperfections in the polymer surface upon its wear rate were examined, under cyclic and steady loading, in order to better understand surface fatigue wear of polymers. The imposed imperfections consisted of vertical artificial deep crack (slit) perpendicular or parallel to the direction of sliding. The study concludes with the followings findings; in general, wear of polymers shows a significant tendency to the type of applied load. Under cyclic loads, polymers show an increase in wear rate compared to those tested under static loads. Such increase was found to increase with the increase in cyclic load frequency. It is also demonstrated that surface cracks results in higher wear rates, particularly under cyclic loads.

• Tribology and Lubricants
• /
• 제37권4호
• /
• pp.136-143
• /
• 2021

This paper presents the loosening behavior that occurs after the application of an external load to internal and external connection types of dental implants using the finite element method. We use fastening force between an abutment and a fixture to clamp the dental implant system; however, loosening and breakage may occur owing to cyclic external loads. In this study, we considered the initial fastening condition in the pre-load analysis and then investigated the change in stress and contact surface status when applying external loads. After the application of the initial fastening load, we verified that the internal connection-type model exhibited a relatively lower stress distribution than that of the external connection-type one. Moreover, we found that the former model showed a lower stress concentration after the application of the external load. In addition, after the application of this load, we found that the higher the shear load acting on the implant system, the higher the possibility of loosening. The study results showed the change in stress distribution and contact surface according to the connection type of the dental implants and the phenomenon of loosening by cyclic loads. We expect that the results of this study will be useful for the study of reliability and design of dental implant systems.

• 한국지반공학회논문집
• /
• 제26권11호
• /
• pp.63-73
• /
• 2010

해상풍력발전기의 기초로 사용되는 단말뚝은 풍력과 파랑하중에 의해 큰 크기의 반복수평하중을 받는다. 본 연구에서는 모래지반에서 반복수평하중을 받는 항타말뚝의 거동 특성을 조사하기 위해서 가압토조와 길이가 다른 3개의 모형말뚝을 이용해서 모형말뚝재하시험을 수행하였다. 실험결과에 따르면 하중의 최초 재하는 그 이후에 가해지는 반복재하보다 말뚝의 수평변위를 크게 발생시키고, 반복하중의 재하횟수가 증가함에 따라 1회 재하로 인해 발생하는 말뚝의 수평변위량은 감소하는 것으로 나타났다. 하중의 한방향 반복재하는 말뚝의 영구수평변위를 재하방향으로 증가시킨 반면, 양방향 반복재하는 최초 재하방향과 반대방향으로 말뚝의 영구수평변위를 증가시켰다. 그리고 반복 하중으로 인한 말뚝의 영구수평변위는 지반의 상대밀도가 감소하거나 말뚝에 가해지는 반복하중의 크기가 커질수록 급격히 증가하였고, 지반의 토압계수나 말뚝의 근입길이 변화에는 크게 영향을 받지 않았다. 또한 모형실험의 결과에 근거해서 하중이 한방향으로 반복재하될 때 말뚝의 영구수평변위와 영구회전각을 예측할 수 있는 산정식을 제안하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.868-880
• /
• 2020

One of the main concerns in the structural integrity of offshore pipelines is mechanical damage from external loads. Pipelines are exposed to fatigue failure in welded joints due to geometric discontinuity. In addition, fatigue loads such as currents, waves, and platform motions may cause significant plastic deformation and fracture or leakage within a relatively low-cycle regime. The 2007 ASME Div. 2 Code adopts the master S―N curve for the fatigue evaluation of welded joints based on the mesh-insensitive structural stress. An extension to the master S―N curve was introduced to evaluate the low-cycle fatigue strength. This structural strain method uses the tensile properties of the material. However, the monotonic tensile properties have limitations in describing the material behavior above the elastic range because most engineering materials exhibit hardening or softening behavior under cyclic loads. The goal of this study is to extend the cyclic stress-strain behavior to the structural strain method. To this end, structural strain-based procedure was established while considering the cyclic stress-strain behavior and compared to the structural strain method with monotonic tensile properties. Finally, the improved prediction method was validated using fatigue test data from full-scale girth-welded pipes.

• Earthquakes and Structures
• /
• 제7권5호
• /
• pp.779-796
• /
• 2014

This experimental investigation was conducted to examine the behavior and response of high-strength material (HSM) reinforced concrete (RC) columns under combined high-axial and cyclic-increasing lateral loads. All the columns use high-strength concrete ($f_c{^{\prime}}$=100MPa) and high-yield strength steel ($f_y$=685MPa and $f_y$=785MPa) for both longitudinal and transverse reinforcements. A total of four full-scale HSM columns with amount of transverse reinforcement equal to 100% more than that required by earthquake resistant design provisions of ACI-318 were tested. The key differences among those four columns are the spacing and configuration of transverse reinforcements. Two different constant axial loads, i.e. 60% and 30% of column axial load capacity, were combined with cyclically-increasing lateral loads to impose reversed curvatures in the columns. Test results show that columns under 30% of axial load capacity behaved much more ductile and had higher lateral deformational capacity compared to columns under the 60% of axial load capacity. The columns using closer transverse reinforcement spacing have slightly higher ductility than columns with larger spacing.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1994년도 가을 학술발표회 논문집
• /
• pp.113-120
• /
• 1994

Large Concrete Panel Structures behave quite differently from frame or monolithic shear wall structures because of the weakness of Joint in stiffness and strength. The joint experiences large deformation such as shear-slip in vertical and horizontal joint and rocking and crushing in horizontal joint because of localized stress concentration, but the wall panels behave elastically under cyclic loads. In order to describe the nonlinear behavior of the joint in the analysis of PC structures, different analysis technique from that of RC structures is needed. In this paper, for analysis of large concrete panel subassemblage subjected to cyclic loads, the wall panels are idealized by elastic finite elements, and the joints by nonlinear spring elements with various load-deflection relationship. The analytical results are compared with the experimental results on the strength, stiffness, energy dissipation and lateral drift, and the effectiveness of this computer analysis modelling technique is checked.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1989년도 봄 학술발표회 논문집
• /
• pp.44-49
• /
• 1989

The primary purpose of using bracings is to improve tile lateral rigidity of main structural system, i.e., columns and beams, by reinforcing them with much smaller members. Conventional design methods consider bracings as tension-only mambers, since difficulties arise in the analysis to consider the P - effects and post-buckling behaviour of the bracing members. This is particulary true for X-bracings. Recently, however, both analytical and experimental studies have been conducted to investigate the more precise and real behaviour of bracing members, especially for the nonlinear un plastic behaviour under cyclic loads. In this study, an analytical model is proposed to investigate the nonlinear behavior of steel bracing members subjected to cyclic loads. Results of tile analysis were compared with previous experimental results, and good agreements were obtained between these results.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.507-512
• /
• 1998

An experimental investigation was conducted to examine the behavior of high strength R/C columns subjected to reversed cyclic and axial loads and to find the relationship between amounts of lateral reinforcement and axial loads ratios. The test parameters of column specimens were the compressive strength of concrete($f`_c$=250, 320, 460, $517kg/\textrm{cm}^2), $ the yield strength of longitudinal steel($f_y$=3700, $5254kg/\textrm{cm}^2), $ axial load ratio(0.3, 0.5, 0.6$f`_cA_g$). The results indicated that axial load can significantly affect and alter the behavior of HS R/C column under inelastic cyclic loadings. Also we found that the relationship between amounts of lateral reinforcement and axial load ratios was $\rho$ =(0.37η+0.15)f`/f.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.565-568
• /
• 1999

The objective of this study is to investigate the hysteretic behaviors of exterior beam-column joints with high strength concrete (f'c≒1000kg/$\textrm{cm}^2$) subjected to cyclic loads. Four exterior subassemblages scaled down about 60% were tested, whose variables were with/without shear reinforcements and with/without slab and spandrel beams. Hoop bars and hooked steel fibers were used as the shear reinforcements. The test results showed that using hooked steel fiber reinforced concrete with volume ratio 1.5% at beam-column joints was very effective to resist shear stress due to cyclic loads.

• 한국지반공학회논문집
• /
• 제32권4호
• /
• pp.41-49
• /
• 2016

해상구조물을 지지하는 말뚝기초는 바람, 조류, 파랑 등의 영향으로 횡방향 반복하중을 지배적으로 받는다. 본 연구에서는 횡방향 반복하중이 말뚝의 횡방향 극한지지력에 미치는 영향을 평가하기 위하여, 서로 다른 세 가지 상대밀도(40%, 70%, 90%)로 조성된 모래지반에서 모형말뚝시험을 수행하였다. 상대밀도 40%로 조성 된 모래지반에서는 횡방향 반복재하 시 말뚝 주변 지반이 조밀해짐에 따라 횡방향 극한지지력이 증가하였다. 반면, 상대밀도 70%와 90%로 조성 된 모래지반에서는 횡방향 반복재하 시 말뚝 주변 지반의 교란효과로 인하여 횡방향 극한지지력이 감소하였다. 이러한 횡방향 극한지지력의 증가 및 감소효과는 횡방향 반복하중의 크기가 커질수록 더욱 명확하게 나타났으며, 모래지반의 포화 여부에는 큰 영향을 받지 않았다. 모형시험 결과를 활용하여 모래지반의 상대밀도, 횡방향 반복하중의 크기에 따른 말뚝의 횡방향 극한지지력 산정 식을 제안하였고, 이를 횡방향 반복하중을 지배적으로 받는 말뚝의 설계 시 활용 가능하도록 하였다.