• 한국측량학회지
• /
• 제24권1호
• /
• pp.9-18
• /
• 2006

본 연구는 GPS 데이터 해석 시 정밀도를 높이고 현장에서 관측시간 내 GPS 측량의 적절성 및 재측 여부 등을 직접 결정할 수 있도록 GPS 데이터 품질관리 프로그램을 개발하는 것에 그 목적이 있다. 본 연구에서 개발된 GPS_QC 프로그램은 관측시간 내 위성의 기하학적 배치(DOP)와 다중경로 오차량, 전리층 지연량 및 사이클 슬립 등의 품질관리 인자(quality control parameters)를 RINEX 형식의 GPS 관측데이터로부터 직접 계산이 가능하도록 설계되었으며, 이러한 품질관리 인자는 시계열 형태와 그래프로 제공된다. GPS_QC 프로그램은 일반 사용자들이 다루기 어려웠던 기존의 복잡한 GPS 데이터 품질 확인을 간편하게 수행할 수 있도록 함으로써 실제 현장에서 잘못된 GPS 관측에 따른 재측여부 등을 직접 결정할 수 있게 함으로써 시간적 경제적 손실을 절감시키고, GPS 위치해석 시 정밀도를 높일 수 있을 것으로 판단된다.

• 동력기계공학회지
• /
• 제13권6호
• /
• pp.95-101
• /
• 2009

The generator for gas turbine power generation consists of the rotor which generates magnetic field, the winding coil which is the path for the field current and the wedge and retaining ring which prevents the radial movement of the coil. Relatively severe deformation was observed at the coil end section during the inspection of the generator for peaking-load operation, and the thermal-electricity and the centrifugal force were evaluated by the simple modeling of the windings to find the cause. But the simulation stress was not sufficient to induce the coil plastic deformation. The analysis result seems to be applicable to the base-load generators which runs continuously without shut down up to a year, but there had been more deformation than simulated for the generator which is started up and shut down frequently. The cause of the coil deformation was the restriction of the expansion and shrinkage. The restriction occurs when the winding coil shrinks, and the stress overwhelms the yield stress and cause the plastic deformation. The deformation is accumulated during the start-ups and shut-downs and the thermal growth occurs. The factors which induce the coil restriction during the expansion and shrinkage should be reduced to prevent the unallowable deformation. The resolutions are cutting off the field current earlier during the generator shut-down, modifying the coil end section to remove the stress concentration and making the insulation plate inserted between the coil end section and the retaining ring have the constant thickness.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제18권3호
• /
• pp.109-118
• /
• 2013

Characteristics of the transport of zero-valent iron nanoparticles (nZVI) in an aquifer were investigated to evaluate an application of nZVI-based reactive zone technology. Main flow direction of groundwater was north. Preferential flow paths of the groundwater identified by natural gradient tracer test were shown northeast and northwest. The highest groundwater velocity was $4.86{\times}10^{-5}$ m/s toward northwest. When the breakthrough curves obtained from the gravity injection of nZVI were compared with the tracer curves, the transport of nZVI was retarded and retardation factors were 1.17 and 1.34 at monitoring wells located on the northeast and northwest, respectively. The ratios of the amount of nZVI delivered to the amount of tracer delivered at the two wells mentioned above were 24 and 28 times greater than that of the well on the main flow direction, respectively. Attachment efficiency based on a filtration theory was $4.08{\times}10^{-2}$ along the northwest direction that was the main migration route of nZVI. Our results, compared to attachment efficiencies obtained in other studies, demonstrate that the mobility of nZVI was higher than that of results reported in previous studies, regardless of large iron particle sizes of the current study. Based on distribution of nZVI estimated by the attachment efficiency, it was found that nZVI present within 1.05 m from injection well could remove 99% of TCE within 6 months.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.40-43
• /
• 2006

Public demand for the heat pump system as a next generation energy equipment is increasing for its eco-friendly and cost-effective advantage. Many researches have been concentrated on how to calculate and develop its own efficiency, while the possible effect of the heat pump operation on the whole subsurface temperature distribution is relatively less considered, During the current study, subsurface temperature disturbance caused by seasonal surface temperature cycle in Busan area and general W-tube heat pump operation is simulated in 3-dimensional heterogeneous medium. It shows that subsurface deeper than 10m from the surface remains nearly unchanged throughout the 4 seasons and groundwater convect ion in highly permeable layer near the surface acts like a main path of heat plume from heat pump system, This implies the significance of detail descript ion in shallow sedimentary layer or highly permeable layer which plays an important role on the regional flow advection and heat transfer. Also, the effect of groundwater convection increases when the arrangement of the 2 injection pipes and 2 extract ion well is maintained parallel to groundwater flow. Therefore, more careful and detail investigation is required before installation and operation of heat pump system that it may not cause any possible change of microbial ecosystem in the shallow subsurface environment or 'contamination of temperature' for groundwater use as well as the loss of efficiency of the equipment itself. This can also help to design the optimized grouting system for heat pump.

• Earthquakes and Structures
• /
• 제10권5호
• /
• pp.1089-1109
• /
• 2016

Modified two-surface model (M2SM) is one of the steel elasto-plastic hysteretic constitutive models that consider both analysis accuracy and efficiency. However, when M2SM is used for complex strain history, sometimes the results are irrational due to the limitation of stress-strain path judgment. In this paper, the defect of M2SM was re-modified by improving the judgment of stress-strain paths. The accuracy and applicability of the improved method were verified on both material and structural level. Based on this improvement, the nonlinear time-history analysis was carried out for a deck-through steel arch bridge with a 200 m-long span under the ground motions of Chi-Chi earthquake and Niigata earthquake. In the analysis, we compared the results obtained by hysteretic constitutive models of improved two-surface model (I2SM) presented in this paper, M2SM and the bilinear kinematic hardening model (BKHM). Results show that, although the analysis precision of displacement response of different steel hysteretic models differs little from each other, the stress-strain responses of the structure are affected by steel hysteretic models apparently. The difference between the stress-strain responses obtained by I2SM and M2SM cannot be neglected. In significantly damaged areas, BKHM gives smaller stress result and obviously different strain response compared with I2SM and M2SM, and tends to overestimate the effect of hysteretic energy dissipation. Moreover, at some position with severe damage, BKHM may underestimate the size of seismic damaged areas. Different steel hysteretic models also have influences on structural damage evaluation results based on deformation behavior and low cycle fatigue, and may lead to completely different judgment of failure, especially in severely damaged areas.

• 한국지능시스템학회논문지
• /
• 제15권6호
• /
• pp.661-667
• /
• 2005

본 논문에서는 서열순서화문제를 위한 새로운 혼합형 유전알고리즘을 제안한다. 제안된 유전알고리즘에서는 보로노이양자 화교차를 교차연산자로 사용하고 경로보전 3-최적화를 지역탐색 휴리스틱으로 사용한다. 보로노이양자화교차는 주어진 문제 인스턴스의 상위 정보를 이용하는 교차연산자이다. 이것은 원래 순회판매원문제를 위해서 제안된 교차연산자이기 때문에 서열순서화문제에 적용하기 위해서는 상당한 변형을 필요로 한다. 본 연구에서는 서열순서화문제에 맞도록 보로노이양자화교차를 적절히 변형하고, 변형된 보로노이양자화교차에서 필요로 하는 가능해생성알고리즘, 선행관계사이클분해알고리즘, 유전자거리지정방법 등을 개발하였다. TSPLIB와 ZIB-MP-Testdata로부터 얻어진 서열순서화문제 인스턴스들에 대한 실험결과, 제안된 유전알고리즘이 비교된 다른 유전알고리즘들에 비해서 더 안정적이고 성능이 우수한 것으로 나타났다.

• 한국BIM학회 논문집
• /
• 제5권3호
• /
• pp.19-32
• /
• 2015

For decades, the productivity issue has been a primary concern for the all stake-holders who participate in domestic construction industry. Especially, between a whole life cycle of building, the construction phase's productivity problem makes or break the entire project. In this respect, the general construction company, who accept the order and construct the building(so called General Contractor), should consider various strategies, such as schedule management, cost management, quality management, inner-crew management, etc., for the productivity improvement., and almost of these management methods have been studied for a long time. But, the researches and studies about the specialty contractor, who construct the building directly in construction site were not sufficiently complete yet. This research begins as an idea which tries to apply the BIM(Building Information Modeling) into the tasks of Specialty contractors for their productivity improvement. And for the effective application of construction BIM to specialty contractors, establish of the BIM project execution plan for them, not the fragmentary adoption of BIM. Therefore, in this paper, we develop the BIM project execution plan for the reinforced concrete companies who conduct the framework construction which located on CP(Critical Path) Especially, we model the "Construction BIM Use List for the RC Work", "BIM Application Master Process" and "BIM Application Detailed Process", and general contractor who use these BIM uses list and process models can manage various specialty contractors about schedule, cost, earned value, quality, safety and environment management systematically.

• Tribology and Lubricants
• /
• 제34권3호
• /
• pp.93-107
• /
• 2018

The purpose of Part I of this study is to find the potential region of wear scarring on engine journal bearings operating at a constant angular crank shaft velocity under firing conditions. To do this, we calculate the applied loads and eccentricities of a big-end journal bearing installed on a four-stroke and four-cylinder engine at every crank angle. Then, we find potential wear regions, such as a minimum oil film thickness, at every crank angle below most oil film thickness scarring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Thus, the wear region is defined as a set of each film thickness below the MOFTSW at every crank angle. In this region, the wear volume changes according to the wear depth and wear angle, depending on the minimum oil film thickness at every crank angle. The total wear volume is the summation during one cycle. Graphical views of the region in the two-dimensional coordinates show the crank angle and bearing angle along the journal center path, indicating the position of the minimum oil film thickness. The results of wear analysis show that the possible wear region is located at a few tens of angles behind the upper center of a big-end bearing at maximum power rpm.

• 전기전자학회논문지
• /
• 제14권1호
• /
• pp.8-16
• /
• 2010

본 논문에서는 CCD 이미지 처리를 위한 최대 15MS/s의 속도의 중저속 아날로그-프론트 엔드(analog-front end, AFE)에서 사용될 수 있는 연속근사 ADC(Successive Approximation ADC, SA-ADC)의 설계를 제안한다. 파이프라인 ADC와 달리 SA-ADC는 동작주파수의 변화에 따른 전력소모의 스케일링(scaling) 효과가 크므로 저속에서 중속에 이르는 넓은 범위의 가변 데이터 처리 속도의 응용에 매우 효과적이다. 제안하는 설계는 입력 신호의 샘플링 동작을 내부 DAC(sub-DAC)로부터 따로 분리한 후, 커패시터 커플링을 통해 차동 결합함으로써 신호경로에 이르는 부하를 크게 줄이는 "차동 커패시터 커플링 기법"의 도입, 연속근사의 기법적 측면에서 signed 구조를 활용하여 데이터 변환주기 이전에 홀드된 입력신호로부터 미리 MSB(sign bit)를 결정함으로써 1사이클의 변환주기를 절약하고 내부 DAC의 하드웨어를 1비트 줄이는 구조와 같은 특징을 갖고 있다. 본 설계는 3.3V $0.35{\mu}m$ CMOS 공정으로써 설계하고 Spectre 시뮬레이션을 이용하여 그 특성을 분석함으로써 CCD 아날로그 프론트-엔드에 적용될 수 있음을 입증하였다.

• 전력전자학회논문지
• /
• 제5권4호
• /
• pp.386-393
• /
• 2000

본 논문에서는 고전력, 고주파 응용에 적합한 저 도통손실 특성을 갖는 향상된 양전압 부분 직렬 공진행 DC/DC 컨버터를 제안한다. 제안된 컨버터는 많은 범위에서 주 스위치의 영전압 스위칭을 보장히며 주 스위치의 전류 스트레스 감소에 의해 저도통 손실 특성올 이룬다. 또한 제안된 컨버터의 보조회로는 주 전력 흐름과 분리되어 있어 주 회로의 공진 시간동안 유효 듀티비 감소는 발생하지 않는다. 보조 회로는 인덕터, 커피시터, 다이오드 그리고 과포화 리엑터의 수동 소자들만으로 구성 되어있다. 따라서 향상된 ZVS PSRC는 전체 시스템의 효율과 전류 스트레스 감소면 에서 개선된 특성을 지닌다. 제안한 컨버터의 동작 원리를 자세히 설명하고 그 타당성올 시뮬레이션과 실험을 통하여 검증하고자 한다.