• Journal of the Microelectronics and Packaging Society
• /
• v.31 no.1
• /
• pp.43-48
• /
• 2024

The discovery of a two-dimensional electron gas (2DEG) at the interface of LaAlO₃ (LAO) and SrTiO₃ (STO) substrates has sparked significant interest, providing a foundation for cutting-edge research in electronic devices based on complex oxide heterostructures. However, conventional methods for producing LAO thin films, typically employing techniques like pulsed laser deposition (PLD) within physical vapor deposition (PVD), are associated with high costs and challenges in precisely controlling the La and Al composition within LAO. In this study, we adopted a cost-effective alternative approach-solution-based processing-to fabricate LAO thin films and investigated their electrical properties. By adjusting the concentration of the precursor solution, we varied the thickness of LAO films from 2 to 65 nm and determined the sheet resistance and carrier density for each thickness. After vacuum annealing, the sheet resistance of the conductive channel ranged from 0.015 to 0.020 Ω·s^-1, indicating that electron conduction occurs not only at the LAO/STO interface but also into the STO bulk region, consistent with previous studies. These findings demonstrate the successful formation and control of 2DEG through solution-based processing, offering the potential to reduce process costs and broaden the scope of applications in electronic device manufacturing.

• Journal of Korean Society of Forest Science
• /
• v.44 no.1
• /
• pp.26-35
• /
• 1979

Factors affecting the survival of out planted Cryptomena and Japaneses Cypress seedlings. (I) - Especially on the drying and water soaking duration ­ There are often the cases of poor survival percentage for the economic forest establishments of Cryplomeria japonica D. Don. and Chamaecyparis obtusa End. This study was carried out to investigate the survival factors of both 1-1 seedlings and Cryptomena cutting Seedlings by room drying conditions, day drying conditions, OED green water soaking treatment and drying duration at the forest nursery of Chonnam National University from February to September. 1979. The results are as follows: 1. From 11 a.m. to 3 p.m. fluctuation in then moisture contents(MC) rapidly decreased and M.C. fluctuation in indoor until 5 p.m. showed the same results with the amount of an hour fluctuation in outdoor. 2. M.C. fluctuations between OED green and non-treatment of these seedlings were silghtly different. 3. The survival percentage of OED green and non-treatment of seedlings were highly significant in the room drying conditions and the day drying conditions respectively The effects of water soaking treatment on rooting was negligible. The survival percentage of seedlings of OED green was higher than that of non-treatment. 4. Although survival percentage of Japanese Cypress was almost in accord with Cryptomena, the power of resistance to drying was lower m Japanese Cypress than m Cryptomeria. 5. Compared with Cryptomena seedlings the survival percentage of Cryptomeria cutting seedlings was higher and not influenced at all in case of being drying for two hours; but it was highly significant in interactions between the drying time and the water soaking time. 6. When Cryptomena and Japanese Cypress seedling become drying in indoor for four days, the survival percentage remarkably reduced after two days and also was highly significant among numbers of drying days.

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.1
• /
• pp.77-85
• /
• 2000

To investigate the practical assessing method of pork quality, 302 carcasses were selected randomly to represent commercial conditions and were probed at 24 hr postmortem (PM) by Danish Meat Quality Marbling (MQM), Hennessy Grading Probe (HGP), Sensoptic Resistance Probe (SRP) and NWK pH-K21 meter (NpH). Also, filter paper wetness (FPW), lightness (L*), ultimate pH (pHu), subjective color (SC), firmness/wetness (SF) and marbling scores (SM) were recorded. Each carcass was categorized as either PSE (pale, soft and exudative), RSE (Reddish-pink, soft and exudative), RFN (reddish-pink, firm and non-exudative) or DFD (dark, firm and dry). When discriminant analysis was used to sort carcasses into four quality groups the highest proportion of correct classes was 65% by HGP, 60% by MQM, 52% by NpH and 32% by SRP. When independent variables were combined to sort carcasses into groups the success was only 67%. When RSE and RFN groups were merged so that there were only three groups (PSE, RSE+RFN, DFD) differentiating by color MQM was able to sort the same set of data into the new set of three groups with 80% accuracy. The proportions of correct classifications for HGP, NpH and SRP were 75%, 61% and 35% respectively. There was a decline in predication accuracy when only two groups, exudative (PSE and RES) and non exudative (RFN and DFD) were sorted. However, when two groups designated PSE and non-PSE (RSE, RFN and DFD) were sorted then the proportion of correct classification by MQM, HGP, SRP and NpH were 87%, 81%, 71% and 66% respectively. Combinations of variables only increased the prediction accuracy by 1 or 2% over prediction by MQM alone. When the data was sorted into three marbling groups based on SM this was not well predicted by any of the probe measurements. The best prediction accuracy was 72% by a combination of MQM and NpH.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.144.2-144.2
• /
• 2016

Diamond-like carbon (DLC) coatings have been widely applied to the mechanical components, cutting tools due to properties of high hardness and wear resistance. Among them, hydrogenated amorphous carbon (a-C:H) coatings are well-known for their low friction properties, stable production of thin and thick film, they were reported to be easily worn away under high temperature. Non-hydrogenated tetrahedral amorphous carbon (ta-C) is an ideal for industrial applicability due to good thermal stability from high $sp^3$-bonding fraction ranging from 70 to 80 %. However, the large compressive stress of ta-C coating limits to apply thick ta-C coating. In this study, the thick ta-C coating was deposited onto Inconel alloy disk by the FCVA technique. The thickness of the ta-C coating was about $3.5{\mu}m$. The tribological behaviors of ta-C coated disks sliding against $Si_3N_4$ balls were examined under elevated temperature divided into 23, 100, 200 and $300^{\circ}C$. The range of temperature was setting up until peel off observed. The experimental results showed that the friction coefficient was decreased from 0.14 to 0.05 with increasing temperature up to $200^{\circ}C$. At $300^{\circ}C$, the friction coefficient was dramatically increased over 5,000 cycles and then delaminated. These phenomenon was summarized two kinds of reasons: (1) Thermal degradation and (2) graphitization of ta-C coating. At first, the reason of thermal degradation was demonstrated by wear rate calculation. The wear rate of ta-C coatings showed an increasing trend with elevated temperature. For investigation of relationship between hardness and graphitization, thick ta-C coatings(2, 3 and $5{\mu}m$) were additionally deposited. As the thickness of ta-C coating was increased, hardness decreased from 58 to 49 GPa, which means that graphitization was accelerated. Therefore, now we are trying to increase $sp^3$ fraction of ta-C coating and control the coating parameters for thermal stability of thick ta-C at high temperatures.

• Korean Journal of Plant Resources
• /
• v.19 no.2
• /
• pp.344-347
• /
• 2006

Watering methods for soybean sprouts could be mainly divided into two groups of overspraying and underwatering. The study was carried out to determine the effect of water supplying method on growth, morphological characteristics, colour and cutting resistance of soybean (cv. Junjery) sprouts and culture temperatures. The morphological characters, fresh and dry weights were measured on the 6th day after their culture, but daily mean temperatures inside the plastic culture boxes were measured by data-loggers. Lateral roots were more formed in the underwatering method (UM) than in the overspraying method (OM). Although their total lengths of both methods were nearly same, OM had longer hypocotyl but UM did longer root than the other. Middle and upper parts of hypocotyl were more thickened in UM than in OM. UM showed more hypocotyl fresh and dry weights than OM. There was, however, no significant difference between the two methods in cotyledon, root, total fresh and dry weights although the culture temperature was higher in OM than in UM.

• Restorative Dentistry and Endodontics
• /
• v.27 no.1
• /
• pp.16-23
• /
• 2002

Physical properties of composite resins such as strength, resistance to wear, discoloration, etc depend on the degree of conversion of the resin components. The purpose of this study was to evaluate the degree of conversion of the composite resins according to the thickness of tooth structure penetrated by light and applied light curing time. The coronal portions of extracted human teeth (one anterior tooth, three posterior tooth) was embedded by pink denture material. the mounted teeth were cut into three illumination sections (1mm thickness enamel section, 1mm thickness dentin section, 2mm thicknes dentin section) and one backing section with cutting wheel. Thin resin films were made by using 6kg pressure between slide glass during 5 minutes Thin resin film was light cured on coupled illumination section during 40sec, 80sec and 120sec. each illumination section was coupled as follows; no tooth structure(X), ename section(E), enamel section + 1mm dentin section(ED1), enamel section + 2mm dentin section(ED2), enamel section + 1mm dentin section + 2mm dentin section(EDD). To simulate the clinical situation more closely, thin resin films was cured against a backing section of tooth structure. The degree of conversion of carbon double bonds to single bonds in the resin films were examined by means of Fourier Transform Infrared Spectrometer. The results were obtained as follows ; 1 As curing time was increased, conversion rate was increased and as tooth thickness which was penetrated by curing light was increased, conversion rate was decreased. 2. At all tooth thickness groups, conversion rate between 80sec and 120sec was not significantly increased(P＞0.05). 3. At 40sec group and 80sec, conversion rate between no tooth structure(X) group and 1mm enamel section(E) group was not significantly decreased(P＞0.05). 4. At 80sec group and 120sec, conversion rate between 1mm enamel section(E) group and 1mm enamel section + 1mm dentin section(ED1) group was not significantly decreased(P＞0.05).

• Journal of the Korean Vacuum Society
• /
• v.17 no.5
• /
• pp.466-472
• /
• 2008

Purple Gold is the alloy consisting of 78wt%Au-22wt%Al, and is expressed as a chemical formula, $AuAl_2$. Lately it is being used for the material of accessories or the decorative ornaments, being one of the colored golds having the peculiar purple color, like White Gold and Pink Gold. Purple Gold has the weak point in shaping through casting process due to the bad malleability and castability, being the intermetalic compound of Au and Al. Therefore, it is possible to produce the final product only by the cutting and the grinding process or to use it as a decorative coat with the thin film evaporation. This study implemented two kinds of thin film experiments. One is the case that heat treatment was made after Au and Al deposition evaporated separately with a weight ratio 78:22 on the 200nm$SiO_2$/Si substrate. The other is the case that the surface deposition was made through the vacuum evaporation, keeping the glass substrate temperature remain room temperature, using the bulk $AuAl_2$ as a source. The final film property was measured, focusing on the Purple Gold's color and thickness through the bare eye inspection, the microstructure analysis, the surface resistance analysis, the color difference analysis, and XRD analysis. Purple Gold was not formed, as the excessive surface agglomeration occurred, in case of being produced and treated thermally with 12.5nmAu/40nmAl/200nm$SiO_2$/Si structure. Our results suggest that of Purple Gold films, showing the same purple color as the bulk's, were successfully deposited with the direct thermal evaporation from the $AuAl_2$ bulk source.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.53 no.1
• /
• pp.28-33
• /
• 2008

Traditionally mungbean (Vigna radiata L.) sprouts has been stored after dehydration to decrease their decay. The study was done to determine the effect of watering for final 12 hours of harvest day on morphological characters and color of mungbean sprouts. The seeds of cv. Zhong Lu 1 were soaked in 50 ppm BA solution immediately before 4 hour aeration and then cultured for 6 days, when water-supplied for final 12 hours or not. After packaged with PE envelops, the sprouts stored 5 days at $8^{\circ}C$, and their morphological characters, fresh and dry weights, and colors were measured everyday. Compared to non-water supplied, water supplied sprouts had thicker hypocotyl diameter in middle part, and higher total fresh weight due to increment of cotyledon and hypocotyl ones although the two sprouts did nearly same in other characters. Only nonwater supplied sprouts showed higher color b value in hypocotyl than water supplied ones although there were not significant differences between them in other color-related characters, meaning that the latter ones were more rapidly decayed during their storage. In non-water supplied sprouts, number of lateral roots, hypocotyl and root lengths, total fresh weight, brightness of hypocotyl and root was decreased since 3 days after storage but cutting resistance of hypocotyl was done since 5 days.

• The Journal of Korean Academy of Prosthodontics
• /
• v.30 no.3
• /
• pp.457-478
• /
• 1992

Electrical resistance strain gauges, brittle-coatings, Moir'e fringe analysis, photoelasticity methods, etc, have been employed in the study of stress analysis and three-dimensional photoelasticity method used in this experiment. The author fabricated a total of 24 samples of maxillary and mandibular edentulous ridges with normal and sharp shapes using epoxy resin, one of the photoelastic materials. In addition, complete denture made from artificial resin teeth in other twoo sizes, large and medium size, were affixed to the specimens and attached to an articulator. The following results were attained by cutting 9 slice specimens into 6mm thick portions, in accordance with the three dimensional photoelastic stress freezing method, to analyze stress distribution status under specific static loading in the central, lateral and protrusive occlusions of the shape of edentulous ridge. 1. In the case of central occlusion, when complete resin artificial teeth in large and medium sizes were used on normal and sharp alveolar ridges, high stress distribution was broadly shown in the labio-buccal sides, and low and concentrated in the lingual sides, in all cases. Generally, the highest stresses were shown at the top of the alveolus, or at 2mm below the top of the alveolus, particularly in the specimen 2, 3, and stresses were more or less the same in the symmetrical right and left sides. 2. In the case of lateral occlusion, when the same load was applied, high stresses were shown broadly at the working sides in both the labio-buccal and lingual sides, and low and concentrated at the balanced sides. The highest stresses were shown in the top of the alveolus on the working sides in specimen 2 portion, and the lowest stresses at the balanced sides in specimen 6, slightly higher stresses were shown at retromolar parts in the balanced sides. 3. In the case of protrusive occlusion, high stresses were broadly shown at the labio-buccal sides, and slightly higher stresses at the top 2, 4, and 6mm parts of the alveolus with concentration. The highest stresses were shown in specimen No. 5 and the lowes stresses in specimen 1, 9 and stresses were more of less the same at the symmetrical right and left sides.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.26 no.2
• /
• pp.147-156
• /
• 1981

Most of the currently available rice threshers in Korea are of head-feeding type originally developed for threshing paddy at grain moisture content of 15 to 17% on wet basis. And prevailing rice harvesting system is swathing or cutting and bundling upright rice crop at a maturity stage of grain moisture content of ca. 28 to 20%, followed by transient natural drying in the field and threshing at grain moisture content of about 17%. The system often allows rather high field loss of rice both quantitatively and qualitatively. These necessitate use of a preharvest desiccant, and diquat has been registered recently as a rice desiccant. Aim of the present study is to determine the best time and rate of diquat application and to evaluate its utility as a rice desiccant under its optimal usage conditions in Korea. Diquat was not so effective for japonica rice varieties while it was very effective for the new varieties bred from indica x japonica crosses. The best time of application was the period from 2 days before to 3 days after physiological maturity of grain (moisture content of 28% w.b.) and the optimal rate was about 330g of diquat ion/ha. Applying diquat at the right time and rate dropped grain moisture to 15 to 16% (w.b.) within a week after treatment in contrast to that of 20 to 24% in untreated rice. Desiccation of rice crop with diquat resulted in 10 to 15% increase in grain resistance to shattering and significant reduction in percent green rice. However, there was no reduction in milled rice yield and percent whole kernel and was no change in the percent chalky rice and percent tinted rice. Diquat use appears highly desirable, if there is no residue problem which has not been studied in the present study.