• 오토저널
• /
• 제9권5호
• /
• pp.49-56
• /
• 1987

This paper is a study on the effect of the cutting speed on the tool wear in turning of the glass fiber reinforced plastics. The wear behavior of cutting tool is studied by means of turning, changing the cutting speed and feed in the wide range. Moreover, the theoretical model applicable to the cutting speed of wide range is analysed. The main results obtained are as follows: The relation between the tool wear and the cutting speed is divided into three range in case of the constant cutting distance. 1) At the low cutting speed, the tool wear is independent of the cutting speed, but dependent mainly on the contact length between tool and glass fiber(lst range). 2) At the high cutting speed, the tool wear is independent of the contact length, and dependent on the cutting speed only(2nd range). The tool wear increases in proportion to the cutting speed. 3) At the higher cutting speed than the speed in the 2nd range, the tool wear is independent both of the cutting speed and the contact length(3rd range). 4) In the 3rd range, tool flank wear is constant and is observed that only the wear of cutting edge increases.

• 대한기계학회논문집
• /
• 제17권5호
• /
• pp.1041-1053
• /
• 1993

본 연구에서는 2차원 절삭중 공구가 공작물로 들어가는 과정에서의 칩형성의 천이적 행동을 실험적으로 연구하고 이 결과를 이용하여 자기추진 로타리 공구를 사용 한 절삭중 발생한 칩의 삼각화 과정을 규명하는 이론적인 모델을 제안하고 이의 타당 성을 실험결과로 입증하려 한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.86-89
• /
• 2002

In NC machining, the ability to automatically generate an optimal process plan is an essential step toward achieving automation, higher productivity, and better accuracy. For this ability, a system that is capable of simulating the actual machining process has to be designed. In this paper, a milling process simulation system for the general NC machining was presented. The system needs first to accurately compute the cutting configuration. ME Z-map(Moving Edge node Z-map) was developed to reduce the entry/exit angle calculation error in cutting force prediction. It was shorn to drastically improve the conventional Z-map model. Experimental results applied to the pocket machining show the accuracy of the milling process simulation system.

• 대한기계학회논문집
• /
• 제17권12호
• /
• pp.2926-2935
• /
• 1993

Chip breaker selection analysis, only being possible through experimental process, was obtained by a applied equation which used an orthogonal cutting model and a basic chip deformation. This equation could present an analysis of the chip breaking phenomena without the use of an actual experimetal method, and it was applied to computer simulation and proved the validity of theory through actual experiments. From these results, an efficient method for finding the optimum conditions of chip breaking was found through an optimized theory being applied to basic program. A finite element model for simulating chip breaking in orthogonal cutting was developed and discussed. By simulation the animation of chip breaking is observed in process on the computer screen.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.721-724
• /
• 2000

This paper presents a prediction of tool deflection and resulting machining error fur sculptured surface productions in the ball-end milling process. Due to the different materials and the dimensions of the tool holder and cutter, a cantilever hem model with three uniform sections is proposed fur the tool deflection model. The ability of this model has been verified by a machining experiment. In this study, cutting force and machining error are investigated. This paper provides the prediction of machining error for sculptured surface to improve machining quality for industrial application.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3195-3201
• /
• 1994

In order to analytically predict tapping torque and thrust force in high speed tapping, a cutting model for main cutting edge with a uniformly restricted tool-chip contact area were developed. From this model equations are derived for the prediction of tapping torque given the cutting conditions, tap geometry, and an empirical factor which is related to the workmaterial. Computed values of torque is shown to compare favorably with those obtained from tapping tests on 16MnCr5. The applied torque about the cutting edge of teeth at lead chamfer is estimated respectively and it is shown that observed value is gradually decreased with following teeth.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 봄 학술발표회논문집
• /
• pp.357-364
• /
• 2000

The three main processes involved in the design of stressed membrane surface are surface form-finding, stress analysis and cutting pattern generation. The last process, cutting pattern generation, is considered as a very important procedure in the aspect of the practical design for the fabric membrane surface. In this paper, The cutting pattern generation technique using the geodesic line algorithms is first introduced. And the numerical examples resulting from this technique are presented. Cable elements are used for the approximating membrane surface and two kinds of model, square line and central line model, are used in pattern generation. Finally, a number of different cutting pattern generation for the same membrane surface is carried out and the numerical results are compared each

• 대한기계학회논문집
• /
• 제17권8호
• /
• pp.1910-1920
• /
• 1993

An experimental study to investigate the unconventional chip formation called triangulation of chip in cutting with a SPRT (self-propelled rotary tool) is performed using acoustic emission (AE) signal analysis. In doing that, a quantitative model of the AE RMS signal in triangulation with a SPRT is first developed. The predicted results from this model show good correlation between the AE RMS signal and the general characteristics of triangular chip formation. Then, effects of various process parameters such as cutting conditions (cutting speed, depth of cut, oblique angle and normal rake angle) and the work material properties on the chip formation in cutting with a SPRT are explored. Special attention is paid to the work material properties which are found to have significant effects on triangulation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.847-850
• /
• 1997

This paper presents a strategy to develop the environmentally conscious machining process. To establish the knowledge the analytical and experimental methodology for he prediction of aerosol concentration due to cutting fluid atomization mechanism in machining operation. The established analytical model which is based on atomization theory analyzes the cutting fluid motion and aerosol generation in machining process. The impinging and evaporation experiments were performance to know the particle size ad evaporation rate of cutting fluid. The predictive models can be used as a basis for environmental impact analysis on the shop floor. It can be also facilitate the optimization of cutting fluid usage in achieving a balanced consideration of productivity and environmental consciousness.

• 한국정밀공학회지
• /
• 제26권1호
• /
• pp.43-50
• /
• 2009

Semi dry cutting known as MQL (Minimum Quantity Lubrication) machining is widely spreaded into the machining shops nowadays. The objective of this research is to suggest how to derive optimum cutting conditions for the milling process in MQL machining. To reach these goals, a bunch of finish milling experiments was carried out while varying cutting speed, feed rate, oil quantity, depth of cut and so on with MQL. Then, response surface analysis was introduced for the variance analysis and the regression model with the experimental data. Finally, desirability function based on regression model was used to obtain optimal cutting parameters and verification experiment was done.