• 한국농공학회지
• /
• 제17권3호
• /
• pp.3885-3893
• /
• 1975

This work was intended to study the cutting graph and vibratory phenomina of a newly developed mower which may be suitable for mowing agricultural product having large and hard stems like corn and sugar beet. The system consists of cutter-bar having Curvilinear-translation motion, which attached to drag-crank mechanism. The motion of equation developed for experimental vibratory system which equipped with the cutter-bar system was established and the parameters defining the system's vibratory motion were experimentally determined. The optimum balancing weight for the cutter-bar am vibratory characteristics of the cutter-bar for various counterweight were analyzed to provide the design and operational conditions. The results of the study are summarized as follows; (1) The cutting graph by the new cutter-bar system depends upon the magnitude of ratio of forward travel(Vm) to crank speed (R$\omega$); The cutting pitch for Vm/R$\omega$ 1 (whole cycle cutting) and Vm/R$\omega$=2/$\pi$ (a half cycle cutting) are 2$\pi$ Vm and 4R, respectively. (2) The experimental vibratory system had been proved to function adequately so that it can be used in determining the required counterweight to minimize the vibratory motion of cutter-bar. (3) Experimentally determined counterweight to give the least vibratory motion was a little greater than the theoretically determined one. With the optimum counterweight it was possible to reduce up to about 87% of the amplitude without counterweight, which may be considered to be within safe operational region. (4) To avoid the actual operation of the cutter-bar at resonance which occured in low frequency ratio, it was considered that the rotational speed of the crank for a specific design of mower should be determined separately in connection with the desired cutting graph.

• Journal of Biosystems Engineering
• /
• 제32권3호
• /
• pp.190-196
• /
• 2007

The purpose of this study is to develop a measurement system of cutter conditions for combine header diagnosis during rice harvesting. A load cell was installed at the locker-arm to measure load fluctuation and an acceleration senor was used to monitor vibration signal of cutter bar. The data were collected from a paddy field during harvesting. The tests were conducted with a normal cutter, a loosened cutter, a broken cutter, and a worn-out connecter pin at the field. The vibration signals converted by FFT (Fast Fourier Transformation), filtered, and normalized. The load data and peak values of vibration signals in four different frequency ranges were used to determine the cutting operation and the cutter conditions of combine. The multiple comparison tests showed that the load data and peak values of vibration signals were important to monitor the cutting operation and cutter conditions of combine header.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.119-125
• /
• 1999

At Wire Rod Mill Plant, wire is made of the billet produced at continuous casting machine, or rolled bloom produced at billeting mill, and the product can be classified of wire of 5.5${\Phi}$ and bar in coil of 14∼42${\Phi}$ in diameter(bar in coil will be referred to as coil as below). At present, wire is produced at POSCO No.1, 2, 3 WRM, coil at garret line of No. 2 WRM. Head and tail of coil are properly cut and treated to scrap to fulfill the customer's satisfaction. This above cutting is done off line, and small size coil can be cut manually with clipper, large size coil with hydraulic cutter. Nowadays, it is being investigated to cut automatically in line with trimming shear after passing mill stand. At the moment, Because the coil produced at the garret line of No.2 WRM is hot 400∼600$^{\circ}C$ and trimming is done manually with cutter, there are always interference from manual operation or safety problem of bad working condition. Not only because of the diversity of the coil size 14∼42${\Phi}$ in diameter, but because of the rolling speed 2.5∼22m/sec, it is required to be equipped with several trimming shear. But this can be accomplished with only one shear installed proper place at this paper.

• Journal of Biosystems Engineering
• /
• 제20권1호
• /
• pp.3-12
• /
• 1995

This study was conducted to investigate the cutting mechanism of the reciprocating knife of combine harvester. The cutting operation of reciprocating knife was demonstrated through the cutting pattern diagram which was drawn by computer graphics. Various kinds and dimensions of standard-type reciprocating knives were analyzed by the developed program. The results are summarized as follows : (1) For the 50mm standard reciprocating knife, the bunching area and the maximum stalk-deflection were decreased rapidly according to the increase of cutting velocity ratio by 1.0 and decreased very slowly over this ratio. But, the secondary cut was occurred at ratio of 1.0 and increased rapidly over this ratio. (2) The 76mm standard knife showed better cutting mechanism than the 50mm, in two respects : the larger cutting area per one stroke and the lower revolutional speed of crank shaft for the same cutting velocity. (3) In respect to the bunching area and the secondary cutting length, the adequate height of 50mm standard reciprocating knife was 45~50mm. (4) In order to maintain the proper cutting mechanism, the adequate cutting velocity at forward speed of 0.5㎧ to 1.2m/s was from 0.4m/s to 1.2m/s for the standard knife.

• Journal of Biosystems Engineering
• /
• 제20권1호
• /
• pp.13-21
• /
• 1995

This study was conducted to investigate the cutting mechanism of reciprocating knife of combine harvester. The cutting operation of reciprocating knife with the arrangement of the low-cutting and the double-cutting was demonstrated through cutting pattern diagram which was drawn by computer graphics. Various kinds and dimensions of reciprocating knives were analyzed using the developed program. The results are summarized as follows (1) The low-cutting type reciprocating knife was represented similar cutting characteristics to the standard type, but the maximum stalk-deflection was decreased as 1/2 level of the standard type. And the first ledger plate should be designed shorter than the second ledger plate. (2) The bunching area and the maximum stalk-deflection for the double cutting knife almost were not changed since cutting velocity ratio of 0.6, but the secondary cut were occurred at ratio of 0.8 and increased rapidly over these ratio. (3) The double cutting knife was recommended for the high speed combine, because its bunching area and the maximum stalk-deflection were decreased as 1/2 level of the standard type. (4) In order to maintain the proper cutting mechanism characterized by the bunching area, the maximum stalk-deflection and the secondary cutting length etc., the adequate cutting velocity at forward speed of 0.5㎧ to 1.2㎧ was from 0.3㎧ to 0.96㎧ for the double cutting knives.

• 한국터널지하공간학회 논문집
• /
• 제23권4호
• /
• pp.233-252
• /
• 2021

본논문은 쉴드 TBM 챔버(Chamber) 내 배토처리 효율성 향상을 위한 연구이다. 현재 국내에서는 TBM 공법을 이용한 시공사례가 증가하는 추세이다. TBM 공법 사용의 증가에 따른 디스크 커터(Disc Cutter), 커터 비트(Cutter bit) 및 세그먼트와 같은 TBM 공법의 연구 또한 증가하는 추세를 보인다. 하지만 챔버와 챔버 내 교반 성능에 대한 연구는 미비한 실정이다. 원활한 배토처리와 굴착토의 거동을 개선하기 위하여 챔버 내 효과적인 믹싱 바 배치에 따른 교반 효율 변화에 대한 연구를 수행하였다. 축소모형 실험은 식별의 용이성을 위하여 색이 다른 플라스틱 소재를 사용하여 지반을 조성하였다. 또한 믹싱 바 배치를 상이하게 하여 4가지 Case로 분류하였으며, 입도분포를 단입도와 다입도로 분류하여 총 8가지의 Case로 실험을 진행하였다. 모든 Case의 커터헤드의 회전속도는 5 RPM으로 동일하며, 실험시간 또한 동일한 조건인 1분 30초로 진행하였다. 교반 효율을 확인하기 위하여 각 Case별 상부, 중부(좌 or 우), 하부 위치의 시료를 채취하여 분석하였다. 축소모형실험 결과 실제 사용되는 Case 1과 Case 1-1보다 새로운 배치방법인 Case 4와 Case 4-1의 교반 효율이 증가하는 양상을 보인다. 그에 따라 챔버 내 믹싱 바 배치를 변경하여 교반 효율을 증가시킬 수 있을 것으로 보이며, 교반 효율증가에 따라 공기 절약에 효과적일 것으로 판단된다. 따라서 본 연구는 국내 쉴드 TBM 공법 활용에 있어 큰 지표로써 작용할 것으로 보인다.

• Current Research on Agriculture and Life Sciences
• /
• 제22권
• /
• pp.41-48
• /
• 2004

본 연구는 예취시 벼 줄기의 절단 저항이 적은 콤바인 예취날 개발에 필요한 기초 자료를 제공하기위하여 예취날의 윗날 내부에 면적 $75mm^2$의 평면 홈을 가공한 개발날과 시중에 판매되는 예취날을 사용하여 절단속도비와 볏짚의 함수율을 인자로 미예취시 예취날의 구동 마찰저항과 예취저항을 측정한 결과는 다음과 같다. 1. 예취날 속도 0.37m/s에서 0.55m/s범위 내에서 단날 구동시의 예취날 구동 마찰저항은 홈 가공을 한 개발 날이 평균 $0.12kg{\cdot}m$로 홈 가공을 하지 않은 기존 날의 평균 $0.16kg{\cdot}m$에 비해 25% 낮게 나타났다. 또한 양날 구동방식에서도 홈 가공을 한 개발말이 기존날에 비해 평균 26%정도 구동 마찰저항이 낮게 나타났다. 2. 절단속도비 10.에서 1.5범위 내에서 홈을 가공한 개발날의 볏짚 예취 저항은 기존 날에 비해 볏짚의 함수율 14.2%, 55.3%, 84.2%에 대해 각각 평균 12%, 15%, 20% 낮게 나타났다. 3. 예취날 구동 방식에 따른 볏짚 예취 저항은 양날구동방식이 $0.20kg{\cdot}m$로 단날 구동방식의 $0.24kg{\cdot}m$에 비해 평균 17%정도 낮게 나타났다. 4. 예취날의 최적 속도비는 볏짚의 함수율 변화에 따라 다르게 나타났으며 함수율 14.2%, 84.2%에 대해 각각 1.2, 1.4로 나타났다.

• 한국방재학회 논문집
• /
• 제8권2호
• /
• pp.1-5
• /
• 2008

본 연구는 상온에서 산소절단기로 철근의 절단시 절단부위로 부터의 고온수열범위와 수열온도를 측정하고 시뮬레이션 결과와 비교함으로써 현장에서 산소절단기를 사용한 철근절단의 가능성을 파악하는 것을 목적으로 하며 그 결과는 다음과 같다. 1. 산소절단기로 철근을 절단하는 경우 절단 부위로부터 1 cm 떨어진 위치의 수열온도는 $700^{\circ}C{\sim}1000^{\circ}C$의 범위에 있으나, 절단부위로부터 2cm떨어진 위치의 수열온도는 200$^{\circ}C$를 넘지 않는 것으로 나타났다. 2 각 직경, 종류별로 철근의 수열온도 분포를 시뮬레이션한 결과 산소 절단시험와 유사한 절단 거리에 따른 온도 분포를 보임으로서 철근 절단 거리에서 2cm 정도의 여유를 갖고 절단할 경우에는 고온 수열에 따른 취성변화가 발생되지 않는다.

• Journal of Biosystems Engineering
• /
• 제19권3호
• /
• pp.175-184
• /
• 1994

This study was conducted to investigate experimentally the basic characteristics of the torque of the cutterbar driving shaft as the double-knife was used instead of the conventional standard single-knife type. A new design for inclined setting of the cutterbar relative to the direction perpendicular to combine harvester movement was investigated to test a possible reduction of concentrated load caused by the simultaneous cutting of many rows. It was evaluated that the maximum torque and mean total power of the driving shaft due to the cutting resistance of the rice straw were largely depended upon the rotational shaft-speed and straw feeding rate, but were resepectively 1.1~2.3 and 1.15~1.34 times higher compared to those while idling. It was also proved that the inclined setting of the cutterbar could save a considerable amount of energy required for its driving shaft.

• Journal of Biosystems Engineering
• /
• 제34권1호
• /
• pp.21-29
• /
• 2009

A rapeseed reaping equipment attachable to a conventional combine was developed in order to harvest rapeseed for bio-diesel materials. This study was carried out to measure the harvest feasibility of a prototype combine in rapeseed fields. Grain, stem and pod flow rate, grain qualities (whole kernel, damaged kernel, unhulled kernel, material-other-than-grain) and grain loss rates (header, threshing, separation) were investigated in each field test. As the result of the fold test, the average grain flow rates of SUNMANG and MS varieties showed 1,430 kg/h and 2,038 kg/h, respectively. The average stem and pod flow rates showed 3,443 kg/h and 6,596 kg/h, respectively. In each working speed, the average whole kernel rate and the material-other-than-grain showed 99.9% and below 0.08%, respectively. In the average grain loss, the rates showed 5.66% in case of SUNMANG and 5.94% in MS. Header loss was higher than other parts for SUNMANG. However, threshing loss was relatively higher than other parts for MS. Header loss rate due to side cutter knifes, however, was not so high when compared with a grain loss due to the cutter bar. Effective field capacity and field efficiency of the prototype combine showed 0.389 ha/h and 44%, respectively. Comparison of customary combine with the prototype combine through field test demonstrated that the header loss was reduced by 69.3% when the prototype combine was used.