• Journal of the Korean Society of Safety
• /
• v.9 no.4
• /
• pp.17-28
• /
• 1994

Chip breaking is important in lathe work for maintaining good surface of the products and safety of operator. The purpose of this study is to investigate the performance of chip breaking and chip shape resulted from the carbide inserts with grooved type and obstruction type chip breaker. Experiments have been performed under the following cutting conditions, (1) constant cutting speed with variable depth of cut and feed rate, (2) constant depth of cut with variable cutting speed and feed rate. Also, the flying distance of chip and it's distribution have been investigated. As a results, good performance of chip breaking can be obtained for small radius of curvature and land width of grooved type chip breaker. And the thickness of chip increase with the increase of feed rate and decrease of cutting speed, and the chip breaking becomes easier with the increase of chip thickness due to the large deformation rate. Obstraction type chip breaker shows better performance of surface roughness than the grooved type. The flying distance of the chips over 90% are less than 1 meter, and the distance decreases as the feed rate decreases.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.643-650
• /
• 2002

The large planar failure has occurred in a rock cut slope of highway construction site in Boeun. This area is considered as unstable since the discontinuities whose orientations are similar to the orientation of the failure plane, are observed in many areas. Therefore, several analysis techniques such as SMR, stereographic analysis, limit equilibrium, numerical analysis, which are commonly used in rock slope stability analysis, are adopted in this area. In order to analyze the stress redistribution and nonlinear displacement caused by cut, which are not obtained in limit equilibrium method, the UDEC and shear strength reduction technique were used in this study Then the factors of safety evaluated by shear strength reduction technique and limit equilibrium were compared. In addition, the factor of safety under fully saturated slope condition was calculated and subsequently, the effect of the reinforcement was evaluated.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.61-67
• /
• 2018

The face milling cutter, which is mainly used for the face milling, is used to cut the Carbon steel(SM20C) in the machining center for 5 times and 10 times respectively. This study clarify the dimensional accuracy characteristics according to the number of fine machining varied the condition of cutting depth, table feed speed and spindle speed. Cutting depth is varied 0.05~0.2mm, table feed speed is varied 0.05~0.2mm/min and spindle speed is varied 1500~2500rpm. As a result, the dimensional accuracy was stable 6 times machining with table feed speed 150mm/min and 10 times machining with table speed 100mm/min and cutting depth 0.05mm regardless times of machining.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.173-180
• /
• 2001

This research is aimed at investigating the dynamic response of cut-and-cover tunnel to seismic waves. We carried out shaking table test which is used a 1/40-scale(the width of prototype tunnel is about 14.2m, the height is about 8.5m) model for this research, and we analyzed the effect of depth of tunnel and slope of the ground in relation to the dynamic responses of tunnel. As a result of the test, the stress and acceleration along the tunnel decreased accordingly to the depth of increment, and this phenomenon is caused by the increase of the confining effect of ground. Also, the dynamic responses of tunnel showed a tendency to rise according as ground declined gently. In comparison the result of shaking table test with that of structural analysis on ordinary condition, we conclude that seismic waves do not affect cut-and-cover tunnel when the depth of tunnel is over the diameter of tunnel.

• FLOWER RESEARCH JOURNAL
• /
• v.19 no.4
• /
• pp.206-211
• /
• 2011

This study was carried the effect of transportation conditions and plant growth regulator on the maintenance of freshness and quality of cut Chrysanthemum 'Baekma'. The quality of cut chrysanthemum 'Baekma' which were stored at $5^{\circ}C$ was better than those of stored at $20^{\circ}C$ and control. When cut mum 'Baekma' was transported stacking boxes with vertical condition after dipping in distilled water, flowering degree, flower size, days to flower appearing degree, and bent neck were delayed. Flowering degree was delayed by $10mg/L^{-1}$ uniconazole spraying, The days to bent neck was delayed by 1,000x daminozide spraying.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.1
• /
• pp.205-212
• /
• 2002

The deterioration rate of concrete structures in urban area is accelerated due to rapid urbanization and environmental pollution. Repair materials and methods newly introduced in Korea should be investigated whether they are appropriate for the urban environment in Korea. The creek concrete structures are exposed in severe environmental condition than others. Based on these background in mind, the study is focused on evaluation of performance on repair materials used to rehabilitate creek concrete structures. To evaluate the performance of repair materials, four kinds of repair materials were selected based on polymer emulsion. This experimental study was conducted on fundamental performance such as setting time, compressive strength, bending strength, bonding strength, thermal expansion coefficient, and durability performance such as chloride diffusion, carbonation, chemical attack, and steel corrosion rate. On the basis of this study, the optimal repair material which is proper to the environment condition can be selected and service life of creek concrete structures can be extended. As a result, the life cycle cost can be reduced and the waste of material resources will be cut down.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.20-27
• /
• 2003

In this paper, the fuel transport characteristics during transient condition was studied by using a Fast Response Flame Ionization Detector(FRFID). The quantitative measurement method for the inducted fuel mass into cylinder is studied. The inducted fuel mass into the cylinder was estimated by using calculated air-fuel ratio by hydrocarbon concentration of cylinder and air flow model. In order to estimate the transportation of injected fuel from the intake port into cylinder, the wall wetting fuel model was used. The two coefficient $\alpha$,$\beta$) of the wall-wetting fuel model was determined from the measured fuel mass that was inducted into the cylinder at the first cycle after injection cut-off To reduce an air/fuel ratio fluctuation during rapid throttle opening, the appropriate fuel injection rate was obtain from the wall wetting model with empirical coefficients. Result of air/fuel ratio control, air/fuel excursion was reduced.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.30-38
• /
• 2003

High-speed machining is one of the most effective technology to enhance productivity especially for hardened die material. High-speed machining can give great advantages for machining of dies and molds. But selection of machining condition is very difficult because of complicated machining mechanism. This paper presents the selection of machining condition in high-speed machining of STD11. Depth of cut, feed rate and spindle revolution are control factors. The effect of the control factors on surface roughness and machining error in Z-direction is discussed to improve machining accuracy.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.341-344
• /
• 2006

LED chips are produced by cutting the sapphire on which GaN is evaporated. To cut the sapphire wafer into each LED chip, at first the wafer is scribed by diamond tool. To get the sharp groove shape for the nice cutting plane it is important the diamond tool shape, load, etc when the wafer is scribed. Here we tried to simulate the scribing process and get the scribing condition to reduce the wear rate of diamond tool for the sharp groove shape.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.108-113
• /
• 2005

In this study, rotary type diamond dressing system for ultra-precision centerless grinding for ferrule was developed at the first time and experiments were conducted with AE sensor and hall sensor system to verify the optimum dressing condition for ultra-precision centerless grinding for ferrule. The correlations with the condition of dressing are evaluated by AE signal analysis with root mean square (RMS) and frequency analysis. And current signals from hall sensor are also studied as a factor of dressing optimum condition selection. Dressing process was conducted to investigate the effects of depth of cut, rotating speed, and the number of overlap to select the optimum condition of rotary dressing system of ultra-precision centerless grinding machine for ferrule fabrication. In order to verify the optimum condition of dressing, AE and current signals were compared with the surface quality of dressing wheel and grinding wheel for ultra-precision ferrule grinding. All of these experiments were completed by Taguchi Methodology to reduce experimental time. Hence, the optimum condition of rotary dressing system for ultra-precision centerless grinding for ferrule fabrication can be selected following to the experiment result from signals of AE and hall sensor.