• Journal of Industrial Technology
• /
• v.23 no.A
• /
• pp.119-130
• /
• 2003

This thesis is results of experimental works on the behavior of the cut-and-cover tunnel. Centrifuge model tests were performed to simulate the behavior of the cut-and-cover tunnels having cross sections of national road and subway tunnels. Model experiments were carried out with changing the cut slope and the slope of filling ground surface. Displacements of tunnel lining resulted from artificially accelerated gravitational force up to 40g of covered material used in model tests, were measured during centrifuge model tests. In model tests, Jumunjin Standard Sand with the relative density of 80 % and the zinc plates were used for the covered material and the flexible tunnel lining, respectively. Basic soil property tests were performed to obtain it's the property of Jumumjin Standard Sand Shear strength parameters of Jumunjin Standard Sand were obtained by performing the triaxial compression tests. Direct shear tests were also carried out to find the mechanical properties of the interface between the lining and the covered material. Compared results model tests estimation with respect to displacements of the lining.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.2
• /
• pp.111-117
• /
• 2016

The cutting performance of a developed small-angle spindle tool was investigated with Al6061 using a TiAlN coated high-speed steel end mill. Up-cut and down-cut processes in a milling machine were carried out at the range of 1000-4000 rpm for spindle speed and 50-300 mm/min for feed rate. As a result, the highest cutting force in the Fx direction was obtained from the up-cut process when the spindle speed was 1000 rpm and the feed rate was 100 mm/min. In the Fy direction, the highest cutting force appeared in the up-cut process at a feed rate of 250 mm/min at the same spindle speed. Conversely, the lowest cutting force came out in the up-cut process at a spindle speed of 4000 rpm and a feed rate of 50 mm/min. As for surface finish, the finest surface roughness was obtained as Ra 0.7642 um at a spindle speed of 4000 rpm and a feed rate of 50 mm/min. Consequently, given the cutting performance of the developed small-angle spindle tool, we conclude that its use in industrial practice is feasible.

• Corrosion Science and Technology
• /
• v.9 no.1
• /
• pp.34-38
• /
• 2010

Electrochemical study on cut edge corrosion of prepainted Zn coated (GI) and 55%Al-Zn coated (GL) steels has been performed in wet-dry cyclic conditions. Maximum width of delaminated polymer coating from the cut edge for GI and GL specimens was evaluated under wet-dry cyclic conditions. The cyclic tests were carried out for 1000 h by changing of relative humidity, where the salt of NaCl was deposited on the specimen every 48 h. The cut edge corrosion test under NaCl deposit indicated that the delamination of the GL specimen progresses at a higher rate than the GI. The electrochemical corrosion monitoring was also performed under condition of alternate exposure to immersion in NaCl solution and drying at 60%RH and $25^{\circ}C$. On the basis of the results of the delamination tests and electrochemical measurements, the mechanism of cut edge corrosion for GI and GL were discussed.

• Asian Journal of Turfgrass Science
• /
• v.7 no.2_3
• /
• pp.121-127
• /
• 1993

This experiment was carried out to compare the varietal differences of dry matter production in rend canarygrass. The varieties examined were Common, Venture, Castor, Palaton and Venture. Reed canarygrass was harvested three times annually, 1st cut(1O, May), 2nd cut(31, July), and 3rd cut(10, Oct.), respectively. The results were summarized as follows ; 1. Dry matter yield were not significant difference between varieties and for the interaction of variety$\times$cut. But, there was significant difference between cuts. 2. There was not significant difference in dry matter yield between the first cut and second cut. But, the dry matter yield of the third cut was poor than the other two cuts. Thus, the average dry matter yield of varieties were 806.1 kg, 730.8kg and 495.8kg /l0a in the first, second and third cut, respectively. 3. In Venture and Palaton, the percentage of dry matter distribution in spring was higher than that of other varieties. In Common, Castor and Vantage, they were not significantly different between the percentage of dry matter distribution in each cut. Above the results suggested that the first group of varieties(Venture and Palaton) were suited to meadow and last group of varieties(Common, Castor and Vantage) were suited to pasture. 4. Average total dry matter yield of varieties was 2,032kg /l0a/yr,(ranged from 1,922kg to 2,180 kg /l0a /yr.)

• Journal of Animal Science and Technology
• /
• v.47 no.2
• /
• pp.147-158
• /
• 2005

The purpose of this study was to find out the effects that daughters' incomplete lactation records affect sire's breeding values through genetic evaluation using RRTDM(random regression test-day model). First, we estimated genetic parameters and breeding values on sires having complete lactation records of daughter by RRTDM, second, we changed complete lactation records of specific sires into incomplete records by various methods. Third, the breeding values were compared between complete and incomplete records. Finally, this study aimed to find out the methods to minimize the estimation errors of young bulls' breeding values. Data used in this study were collected from the dairy herd improvement program, and a total of 97,562 records were composed of 10,929 first parity with both parents known, since 1999. Breeding values on the daughters from randomly chosen sires were calculated and compared with among 90 day, 150day, and 200 day's incomplete records. For milk yields, sire's ranks of breeding values used by complete lactation records were very different from sire's ranks of breeding values obtained by incomplete lactation records(Rank_90 cut, 150cut, 200 cut).The differences were also obtained between complete lactation records(per305_full) and incomplete lactation record (per_90 cut, 150cut, 200 cut) in breeding values regarding persistency. Especially, the differences between per_90 cut and per305_full were very large(from 1.8 kg to 145kg).

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.2 no.4
• /
• pp.64-73
• /
• 1999

This study was conducted to find out the effects of hydroseeding material and seed mixture on the revegetation of rock cut-slopes by PEC4 (Polymer-Ecology-Control) Hydroseeding Measures. PEC4 hydroseeding material was applied to four cut-slopes using hydroseeding measures from April to August, 1999, and the field survey was carried out by monthly. PEC4 material consisted of bark compost and organic soil amendments. This material has high content of organic matter and high level of water holding capacity. PEC4 hydroseeding material shows low level of soil hardness, so it gives to good condition for seed germinating and plant growing in early stage. PEC4 material attached at rock cut-slopes by two types of adhesive agent was not eroded by rainfall. The plant coverage and number of plant species were affected by mixing ratio of seeds and seeding timing. From the viewpoint of plant establishment, the optimal hydroseeding timing of mixed seeds for plant growth seems to be in May. Most of the plant seeds were germinated well and they covered rock cut-slopes so quickly and effectively. Plant importance value of Silene armeria and Platycodon grandiflorum. were higher than any other seeded-native species in the competition between native species and exotic species, so they have enough possibility to be used for slope revegetation works. Thus it leads to conclusion that the revegetation method used in this experiment was a very effective method for plant establishment on rock cut-slopes.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.3
• /
• pp.8-15
• /
• 2004

A significant error in the end milling processes is generated due to using slender tools of which the strengths are not sufficient. In order to obtain the desired machining accuracy, therefore, it is general that at first the rough cut is implemented, then the finish cut is followed. The rough cut eliminates large volume and the finish cut does the remained part. This remaining portion after the rough cut is called as the finish allowance. Larger finish allowances make it hard to get precise dimensions at a following finish cut. Smaller finish allowances are helpful for good dimension, but it sometimes is responsible for inferior surface qualities and over cuts. This study suggests a guidance for the optimum finish allowance for machining accuracy improvement, in which the rough cuts are regulated to remain the desired margins without any over cuts. Some experiments were carried out with various cutting conditions including the change of tool strengths and depth of cuts, and also extended to up millings as well as down millings.

• Journal of Korea Game Society
• /
• v.14 no.5
• /
• pp.137-146
• /
• 2014

Recently, the games on the market are getting rich and excellent in the category of design and productions. The style and production quality of cut-scenes also have achieved a continuous development, so how to stand out from multiple designs and gain popularity always acts as a challenge to designers. However, such design strategy up to developers will be failed to judge whether or not design achievements are loved by players and thus cannot meet rapidly changing market demands on both in a quantity and quality. Therefore, this study holds that cut-scene design for video games must set out from user-centered design(UCD). According to literatures with respect to product market, we know that Market Pull imposes far more impacts on success in bringing new products to the market than the technology Push, hence players actually determines the success of a game in competitive game market. This study will help to enhance the immersion of playing game, including the interest and standing out the designer's message without distorting the original impression in the game publishing environment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.63-69
• /
• 1999

In tis study the effects of the maximum grit depth of cut on the grinding characteristics were investigated. They are AE signals produced during grinding processes have been studied to find out the appropriate AE parameters for assessing grinding processes. SM45C steel has been ground under the conditions yielding removal rate of workpiece 100, 200,300, and 400m{{{{ {m }^{3 } }}}}/min which was achieved by altering workpiece velocity(v) and apparent depth of cut(Z). According to the experimental result the value of surface roughness increases but grinding power energy rate of AE signal(AErmas2) and specific grinding energy consumed decrease as increasing the maximum grit depth of cut.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.693-698
• /
• 2008

For designing intensity modulation type optical microphone, the irradiance distribution which can be applied to inclined-cut geometrical configuration is suggested. The model is important in analysis of response characteristics f3r intensity modulation type optical microphone. To overcome low sensitivity problem in intensity modulation type optical microphone, inclined-cut optical fiber is considered here. Based on optical geometry, the inclined-cut optical fiber sensor is designed and fabricated. The experiments are carried out to evaluate sensor performance.