• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.2
• /
• pp.147-152
• /
• 2012

This paper dealt with the frequency component analysis of acoustic signals produced by corona and series-arc discharges as a diagnostic technique for closed-switchboards. Corona and series-arc discharge were simulated by a needle-plane electrode and an arc generator specified in UL1699, respectively. Acoustic signal was detected by a wideband acoustic sensor with a frequency bandwidth of 4 Hz~100 kHz (-3 dB). We analyzed frequency spectrums of the acoustic signals detected in various discharge conditions. The results showed that acoustic signals mainly exist in ranges from 30 kHz to 60 kHz. From the experimental results, an acoustic detection system which consists of a constant current power supply (CCP), a low noise amplifier (LNA) and a band pass filter was designed and fabricated. The CCP separates the signal component from the DC source of acoustic sensor, and the LNA has a gain of 40 dB in ranges of 280 Hz~320 kHz. The high and the low cut-off frequency are 30 kHz and 60 kHz, respectively. We could detect corona and series-arc discharges without any interference by the acoustic detection system, and the best frequency is considered in ranges of 30 kHz~60 kHz.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2070-2078
• /
• 2014

In this work, the frequency response of gate-all-around (GAA) Ge/GaAs heterojunction tunneling field-effect transistor (TFET) with hetero-gate-dielectric (HGD) and pnpn channel doping profile has been analysed by technology computer-aided design (TCAD) device-circuit mixed-mode simulations, with comparison studies among ppn, pnpn, and HGD pnpn TFET devices. By recursive tracing of voltage transfer curves (VTCs) of a common-source (CS) amplifier based on the HGD pnpn TFET, the operation point (Q-point) was obtained at $V_{DS}=1V$, where the maximum available output swing was acquired without waveform distortion. The slope of VTC of the amplifier was 9.21 V/V (19.4 dB), which mainly resulted from the ponderable direct-current (DC) characteristics of HGD pnpn TFET. Along with the DC performances, frequency response with a small-signal voltage of 10 mV has been closely investigated in terms of voltage gain ($A_v$), unit-gain frequency ($f_{unity}$), and cut-off frequency ($f_T$). The Ge/GaAs HGD pnpn TFET demonstrated $A_v=19.4dB$, $f_{unity}=10THz$, $f_T=0.487$ THz and $f_{max}=18THz$.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.6
• /
• pp.30-38
• /
• 1998

In this paper, a new CMOS current-mode integrator is proposed that can apply the basic building block of the low-voltage high frequency current-mode active filter. And tuning circuits that control the gain and unity gain frequency of them is designed. The proposed integrator is composed of the CMOS complementary circuit which can extend transconductance of an integrator. Therefore, the unity gain frequency which is determined transconductance and MOSFET gate capacitance can be expanded by the proposed integrator. The unity gain frequency of the proposed integrator is increased about two times larger than that of the conventional continuous-time integrator with NMOS-gm. And also, cut-off frequency and gain of the active filter can be controlled with the designed tuning circuit. From the result, we can reduce errors on fabrication. And then, 3rd-order low-pass active filter is designed as an application circuits. These results are verified by the small signal analysis and the 0.8$\mu\textrm{m}$ parameter HSPICE simulation.

• Journal of electromagnetic engineering and science
• /
• v.14 no.1
• /
• pp.36-42
• /
• 2014

In this paper, an epsilon near zero (ENZ) tunneling circuit using a double-ridge rectangular waveguide (RWG) is proposed for the miniaturization of a waveguide component. The proposed ENZ channel and is located in the middle of the input-output RWG (IORWG). The ratio of the height to the width of the channel waveguide is very small compared to the IORWG. By properly adjusting the ridge dimensions, the tunneling frequency of the proposed ENZ channel can be lowered to near the cut-off frequency of the IORWG. For the proposed ENZ tunneling circuit, the approach adopted for extracting the effective permittivity, effective permeability;normalized effective wave impedance, and propagation constant from the simulated scattering parameters was explained. The extracted parameters verified that the proposed channel is an ENZ channel and electromagnetic energy is tunneling through the channel. Simulation and measurement results of the fabricated ENZ channel structure agreed.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.6
• /
• pp.1763-1768
• /
• 2016

This paper presents the electrical characteristics of the gallium nitride (GaN) current aperture vertical electron transistor (CAVET) by using two-dimensional (2-D) technology computer-aided design (TCAD) simulations. The CAVETs are considered as the alternative device due to their high breakdown voltage and high integration density in the high-power applications. The optimized design for the CAVET focused on the electrical performances according to the different gate-source length ($L_{GS}$) and aperture length ($L_{AP}$). We analyze DC and RF parameters inducing on-state current ($I_{on}$), threshold voltage ($V_t$), breakdown voltage ($V_B$), transconductance ($g_m$), gate capacitance ($C_{gg}$), cut-off frequency ($f_T$), and maximum oscillation frequency ($f_{max}$).

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.301-303
• /
• 2001

In this paper we present a Capacitor Charging Power Supply (CCPS) using a series-resonant three-level inverter topology to improve voltage regulation and use semiconductor switches having low blocking voltage capability such as MOSFETs. This inverter can be operated with two modes, Full Power Mode (FPM) and Half Power Mode (HPM). In FPM inverter supplies the high frequency step up transformer with full DC-link voltage and in HPM with half DC-link voltage. HPM switching method will be adopted when CCPS output voltage reaches the preset target value and operates in refresh mode-charge is maintained on the capacitor. In this topology each semiconductor devices blocks a half of the DC-link voltage[2]. A 15kW, 30kV CCPS has been built and will be tested for an electric precipitator application. The CCPS operates from an input voltage of 500VDC and has a variable output voltage between 10 to 30kV and 1kHz repetition rate at 44nF capacitive load [3]. A resonant frequency of 67.9kHz was selected and a voltage regulation of $0.83\%$ has been achieved through the use of half power mode without using the forced cut off the switch current [1]. The theory of operation, circuit topology and test results are given.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.35-44
• /
• 2009

Long stroke Fast Tool Servo (LFTS) with maximum stroke of $432{\mu}m$ is designed, manufactured and tested for fabrication of optical free-form surfaces. The large amount of stroke in LFTS has been realized by utilizing the hinge and lever mechanisms which enable the displacement amplification ratio of 4.3. In this mechanism the peculiar shape was devised for maximizing the displacement of end tip in LFTS and special mechanical spring has been mounted to provide the sufficient preload to the piezoelectric actuator. Also, its longitudinal motion of tool tip can be measured by capacitive type displacement sensor and closed-loop controlled to overcome the nonlinear hysteresis. In order to verify the static and dynamic characteristics of designed LFTS, several features including step response, frequency response and cut-off frequency in closed-loop mode were experimentally examined. Also, basic machining result shows that the proposed LFTS is capable of generating the optical free-form surface as an additional axis in diamond turning machine.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.4
• /
• pp.339-343
• /
• 2006

We observed the application possibility of inductive coupler for the underground high-voltage power line communication by means of analysis of signal transmission characteristics and magnetic properties on annealing temperatures for high-permeability Fe-base amorphous alloys. The best electromagnetic and transmission characteristics were shown in nano-crystalline precipitated alloy annealed at temperature $510^{\circ}C$. The transmission characteristics in the low-frequency band depend on permeability of magnetic core materials and its properties of high-frequency band can be improved by impedance matching. Using the high pass filter embedded in the coupler, other noise signal band except for communication signals could be cut off.

• Journal of the Korea Society of Computer and Information
• /
• v.3 no.2
• /
• pp.77-84
• /
• 1998

The continuous time signal system by development of CMOS technology have been receiving consideration attention. In this paper, Low pass filter using CMOS floating resistor have been designed with cut off frequency for speech signal processing. Especially a new floating resistor consisting entirely of CMOS devices in saturation has been developed. Linearity within $\pm$0.04% is achieved through nonlineartiy via current mirrors over an applied range of $\pm$1V. The frequency response exceeds 10MHz, and the resistors are expected to be useful in implementing integrated circuit active RC filters. The low pass filter designed using this method has simpler structure than switched capacitor filter. So reduce the chip area. The characteristics of the designed low pass filter using this method are simulated by pspice program.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.1
• /
• pp.32-38
• /
• 2002

This paper describes a development of a portable physical activity monitoring system using two accelerometers to quantify physical activity. The system hardware consists of two piezoresistive accelerometers, amplifiers with gain of 30, lowpass filters with cut-off frequency of 15Hz, offset control circuits, one-chip microcontroller and flash memory card. In order to evaluate the performance of the system we acquired 3 channel data at 32 sample/sec from body-fixed accelerometers in chest and right upper leg. And then the acquired data were processed by MatLab on personal computer. We tried to distinguish not only fundamental actions which are steady-state activities such as standing, sitting, and lying but also dynamic activities with walking, up a stairway, down a stairway, and running. Five subjects participated the evaluation process which compare the video data with the measured data. As a result, the activity classification rate of 90.6% on average was obtained. Overall results showed that the steady-state activities could be classified from the low component of 3-axis acceleration signal and dynamic activities could be distinguished from frequency analysis using wavelet transform and FFT. Finally, we could find that this system can be applied to acquire and analyze the static and dynamic physical activity data.