• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.130-135
• /
• 1995

GaAs power MESFET's with 0.5 .mu.m gate length using a conventional UV lithography and angle evaporations are fabricated and then DC and RF characteristics are measured and carefully analyzed. The 0.5$\mu$m GaAs power MESFET's are fabricated on epi-wafers which have an undoped GaAs layer inbetween n+ and n GaAs layers grown by MBE, and by the processes such as an image reversal(IR), air-bridge, and our developed 0.5 .mu.m gate fabrication techniques. The total gate widths of the fabricated 0.5$\mu$m GaAs power MESFETs are 0.6-3.0 mm, the current saturation of them 80-400 mA, the maximum linear and RF output power of them 60-265 mW. The current gain cut-off frequencies for the 0.5$\mu$m GaAs power MESFETs varies 13-16 GHz. For the test frequency of 10 GHz the maximum unilateral transducer power gains and the power added efficiencies of the GaAs power devices are 7.0-2.5 dB and 35.68-30.76 %, respectively.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.88-91
• /
• 2000

An MMIC oscillator operating at the 24.55 GHz has been designed using 0.2 ${\mu}{\textrm}{m}$AlGaAs/InGaAs/GaAs Pseudomorphic HEMT technology. The active device used in the oscillator design has a 0.2 ${\mu}{\textrm}{m}$ gate length PHEMT with 4$\times$80 ${\mu}{\textrm}{m}$ gate width. We obtained 4.08 dB of S$_{21}$ gain and 317 mS/mm of transconductance, and extrapolated unit current gain cut-off frequency (f$_{T}$) and maximum oscillation frequency (fmax) were 62 GHz and 120 GHz, respectively. The circuit are based on a series feedback and negative resistance topology. Microstrip line open stub is used to terminating. The oscillator circuits has designed for delivering maximum power to load and conjugated matching. The simulated small signal negative resistance was 50 Ω. We obtained 1.002 of loop gain and 0.0005$^{\circ}$angle from the simulation by HP libra 6.1. The layout for oscillator is 1.2$\times$1.8 $\textrm{mm}^2$.>.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.386-391
• /
• 1998

The effect of the changes in parameter angles(precone, droop, sweep) on the lead-lag damping was focused on. Experiment was made with hingeless 4-blade rotors and NACA 0012 airfoil. For the measurement of the rotating natural frequencies and lead-lag damping, non-rotating swash plate was oscillated at the regressing lag mode frequency and the data were acquired after the excitation was cut off. Analysis was made using a finite element formulation based on Hamilton's principle. The main blade is assumed as elastic beams. Quasi-steady strip theory is used to obtain aerodynamic forces, and non-circulatory forces are also included.

• Radiation Oncology Journal
• /
• v.6 no.2
• /
• pp.277-281
• /
• 1988

Although widely used in external beam treatment planning, computed tomography scans are infrequent in incranial tumors by implanting of Radioactive isotope. This incranial brachytherapy has only become possible by using CT scans and stereotaxic operation methods. The coincidence of single source and tumor axes in brachytherapy is very important to determine the therapeutic dosages. Eventhough using the CT scan, according to spatial location of tumor tying, the section of tumor will be seen enlargement, cause the tumor will be cut off with slight angle to its axes. Correct analysis of tumor size from source is required for rotated axes in analytical geometry.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.5
• /
• pp.457-462
• /
• 1987

Stochastic stability criterias for ocean wave analysis add simulation are studied using the data simulated by the linear superposition method. To clarify the criterias, the effects of the simulation parameters on the variance of stochastic properties of ocean waves are investigated, and the stable conditions of the parameters are estimated through the comparative study on the stochastic properties of simulated waves and well-known ocean waves. The simulation parameters considered are high frequency cut-off, data length, and number and phase angle of component waves. Statistical characteristics analysed are wave height, period and steepness, and the formation of groups of higher waves, resonance periods, steeper higher waves and extreme run-length of the run.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.712-718
• /
• 2013

This paper proposes a control method for reducing the total harmonic distortion (THD) of the grid current of three-phase grid-connected inverter systems when the grid voltage is distorted. The THD of the grid current caused by grid voltage harmonics is derived by considering the phase delay and magnitude attenuation due to the hardware low-pass filter (LPF). The Cauchy-Schwarz inequality theory is used in order to search more easily for the minimum point of the THD. Both the gain and angle of the compensation voltage at the minimum point of the THD of the grid current are derived with the variation of cut-off frequencies of the hardware LPF. Simulation and experimental results show the validity of the proposed control methods.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.1
• /
• pp.30-36
• /
• 2004

An iterative sliding mode observer is proposed to sensorless control of a PMSM(Permanent Magnet Synchronous Motor). The proposed sliding mode observer has the character which is robust to the disturbance and parameters variation. A low pass filter with the variable cut-off frequency is also proposed to compensate the delay of the rotor angle according to the rotor speed, it is led to save memory and minimize operation time. Experimental results show that the proposed sliding mode observer leads to the proper performance.

• International Journal of Aerospace System Engineering
• /
• v.3 no.2
• /
• pp.14-21
• /
• 2016

This paper presents research on predicting the possible intercept time for a Nodong missile based on its flight trajectory. North Korea possesses ballistic missiles of various ranges, and nuclear warhead miniaturization tests and ballistic missile launch tests conducted last year and in previous years have made these missiles into a serious security threat for the international community. With North Korea's current miniaturization skills, the range of the nuclear capable Nodong missiles can be adjusted according to their use goals and operating environment by using a variety of adjustment methods such as payload, fuel mass, Isp, loft angle, cut-off, etc., and therefore precise flight trajectory prediction is difficult. In this regards, this research performs model simulations of the flight trajectory of North Korea's domestically developed Nodong missiles and uses these as a basis for predicting the possible intercept times for major ballistic missile defense systems such as PAC-3, THAAD, and SM-3.

• The Korean Journal of Applied Statistics
• /
• v.25 no.6
• /
• pp.1027-1036
• /
• 2012

Among various biometrics recognition systems, statistical fingerprint recognition matching methods are considered using minutiae on fingerprints. We define similarity distance measures based on the coordinate and angle of the minutiae, and suggest a fingerprint recognition model following statistical distributions. We could obtain confidence intervals of similarity distance for the same and different persons, and optimal thresholds to minimize two kinds of error rates for distance distributions. It is found that the two confidence intervals of the same and different persons are not overlapped and that the optimal threshold locates between two confidence intervals. Hence an alternative statistical matching method can be suggested by using nonoverlapped confidence intervals and optimal thresholds obtained from the distributions of similarity distances.

• Current Optics and Photonics
• /
• v.4 no.6
• /
• pp.545-550
• /
• 2020

We propose a hole-filling method to solve discontinuous depth representation and to reduce the visible seams and cracks that cause the limitation of the viewing angle of the three-dimensional (3D) image in the multilayer type 3D display system. The occlusion and the disocclusion regions between layers, such as the visible seams and cracks, are a major bottleneck of the multilayer type 3D display system to represent a volumetric 3D image by stacking multiple images. As a result, in the reconstructed 3D image, the visible seams and cracks appear as brighter overlapping and undesirable cut-off. In order to resolve the problems above, we applied the depth-fused effect to the sub-depth map generating algorithm and improve the viewing characteristics of the multilayer type 3D display. The experimental demonstrations are also provided to verify the proposed scheme.