• Geomechanics and Engineering
• /
• v.30 no.5
• /
• pp.423-435
• /
• 2022

Ground vibration generated repeatedly in blasting tunnel excavation sites is known to be one of the major hazards induced by blasting operations. Various studies have been conducted to minimize these hazards, both theoretical and empirical methods using electronic detonator, the deck charge method, the center-cut method among others Among these various existing methods for controlling the ground vibration, in this study, we investigated the cut method. In particular, we analyzed and compared the V-cut method, which is commonly used in tunnel blasting, to the double-drilled parallel method, which has recently been introduced in tunnel excavation site. To understand the rock fragmentation efficiency as well as the ground vibration controllability of the two methods, we performed in-situ field blasting tests with both cut methods at a tunnel excavation site. Additionally, numerical analysis by FLAC3D has been executed for a better understanding of fracture propagation pattern and ground vibration generation by each cut method. Ground vibration levels, by PPVs measured in field blasting tests and PPVs estimated in numerical simulations, showed a lower value in the double-drilled parallel compared with the V-cut method, although the exact values are quite different in field measurement and numerical estimation.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.4 no.4
• /
• pp.287-300
• /
• 2002

Composition Presplitting Angle Cut (COPA-Cut) is a newly developed blasting method for tunnel excavation. Contrary to existing methods, COPA-Cut first creates presplitting by tension crack in cut. In this study, field tests measuring the advance efficiency, noise and ground vibration were performed in order to verify the presplitting effect. To compare the economy and workability, tests were simultaneously performed by COPA-Cut and existing method on the same condition. Results show that COPA-Cut increased advance efficiency and decreased noise and ground vibration. Also, it was confirmed that COPA-Cut is superior to existing method in terms of economy, workability and quality control.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.518-522
• /
• 2011

Cartesian grid system has mainly been used in the casting simulation even though it does not nicely represent sloped and curved surfaces. These distorted boundaries cause several problems. A special treatment is necessary to clear these problems. A cut cell method on Cartesian grids has been developed to simulate three-dimensional mold filling Cut cells at a cast-mold interface are generated on Cartesian grids. Governing equations were computed using volume and areas of cast at cut cells. In this paper, we propose a new method that can consider the cutting cells which are cut by casting and mold based on the patial cell treatment (PCT). This method provides a better representation of geometry surface and will be used in the computation of velocities that are defined on the cell boundaries in the Cartesian gird system. Various test examples for several casting process were computed and validated. The analysis results of more accurate fluid flow pattern and less momentum loss owing to the stepped boundaries in the Cartesian grid system were confirmed. We can know the momentum energy at the cut cell is conserved by using the cut cell method. By using the cut cell method. performance of computation gets better because of reducing the whole number of meshes.

• Explosives and Blasting
• /
• v.25 no.1
• /
• pp.31-43
• /
• 2007

In most tunnel constructions in South Korea, blasting has been widely used as an excavation method. In tunnel blasting, the center-cut to induce first free surface is very important for enhancing excavation efficiency and reducing vibration caused by exploding. This paper introduces new center-cut method named SAV-cut (Stage Advance V-cut) developed on the concept of V-cut. Significant features of SAV-cut are the center hole and stepwise ignition. Many field tests and numerical analysis were carried out to analyze the mechanical behavior and blasting vibration. From the results, the newly developed SAV-cut was proved as an effective center-cut method for both increasing blasting efficiency and decreasing blasting vibration.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.06a
• /
• pp.33-42
• /
• 2003

Since the cut slope has been big concern due to frequent failures, the government decided to include cut slopes in the“Act for Safety Control of Public Structures”. Based on the Act, the cut slope whose height is over 50m and length is over 200m should be inspected on the regular basis. According to the Act, KISTEC developed the objective evaluation method for the condition of cut slope. The evaluation method is divided into two categories: evaluation for damaged condition and evaluation for failure affecting factor. Based on the evaluation results, the cut slope is graded from A to E. In this study, the process to evaluate the cut slope condition and the evaluation criteria to divide the grade of cut slope are introduced.

• Tunnel and Underground Space
• /
• v.4 no.3
• /
• pp.237-249
• /
• 1994

A new type of cut method, called SK-cut, was developed in order to overcome the shortcomings of the conventional V-cut and Burn-cut blasting methods. Total 190 times of test blasts were performed for the evaluation of the efficiency of new blasting method. V-cut, Burn cut and SK-cut were compared by applying them to the excavation of main gallery and construction tunnel of underground oil storage cavern. Test results showed that excavation efficiency of the new method was increased by 5.9~9.8% and that specific charge was reduced to 71~92%.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1522-1529
• /
• 2009

When a shaft is excavated in Korea, the mechanized method such as RBM(Raise Boring Machine) or RC(Raise Climber) is used independently of depth. But usually, the mechanized method is useful for the deep depth. On the contrary, when the depth of shaft is short, the cost of excavation increase. So in the case of shaft constructon less than 100m, we need to consider more suitable method of shaft construction such as Stage-cut which is one of blasting methods. Stage-Cut is widely used in the field of shaft construction in Japan as a tool of rock excavation. The main purpose of this study is to provide technical guidance for design and construction of shafts in rock, using Stage-cut method which is suitable for 20m~80m depth shaft. In this study, Blasting tests was performed in field, according to rock classification. Finally, the stage-cut method which is suitable for the geology of Korea was developed.

• The Research Journal of the Costume Culture
• /
• v.20 no.4
• /
• pp.594-603
• /
• 2012

This study aimed to investigate a bias pattern making method with geometrical approach. The bias-cut dress has soft silhouette of drape in the garment. However, the bias cut dress has problem of satisfying the intended garment size spec. This problem occurs from various sources. The main reason is that the bias-cut fabric tends to stretch on longitudinal direction and to shrink horizontal direction when it was hung on the body. The goal of this study was to develop a bias-cut dress pattern making method satisfying the intended garment size spec. The researchers developed the geometrical method of measuring dimensional change by calculating the compensation ratio of the fabric in true bias direction. The compensation ratio was calculated by applying draping ratio of the fabric. Three types of fabrics were used in the experiment. The warp and weft crossing angle of fabric was ranged from $78^{\circ}$ to $82^{\circ}$. The fabrics stretched longitudinally 6.9~9.9% and shrank horizontally 7.2~11.0%. The compensation ratio of the bias-cut pattern for sample dress was calculated for each fabric type. Two types of experimental bias-cut dress patterns were developed for each fabric. One pattern was made with applying full compensation ratio and the other one made with applying partial ratio of the fabric. Experimental dresses were made with these patterns. The results of the evaluation showed that the bias-cut dress pattern applying the partial compensation ratio was more appropriate than the pattern applying the full compensation ratio.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.245-248
• /
• 2005

During manufacturing thick composite cylinders, large thermal residual stresses are developed and induce catastrophic interlaminar failures. Since the residual stresses are dependent on many process parameters, such as temperature distribution during cure, cure shrinkage, winding tension, and migration of fibers, calculation of the residual stresses is very difficult. Therefore a radial-cut method have been used to measure the residual stresses in the composite cylinders. But the conventional radial-cut method needs to know numerous material properties which are not only troublesome to obtain but also vary with change of fiber arrangement during consolidation. In this paper, a new radial-cut method with cut-cylinder-bending test was proposed and the measured residual stresses were compared with calculated thermal residual stresses. It was found that the new radial-cut method which does not need to know any of material properties gave better estimation of residual stresses regardless of radial variation of material properties. Additionally, interlaminar tensile strength could be obtained by the cut-cylinder-bending test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.45-54
• /
• 2013

In this paper, a theoretical weight-reduction method was suggested to substitute an underframe material of a box-type bodyshell having cut-outs with an alternative light-weight material. To utilize the material substitution method previously developed for a box-type hybrid bodyshell not having cut-outs, we derived a box-type baseline model without cut-outs which is similar to the stiffness condition of a box-type bodyshell having cut-outs. To do this, the thicknesses of roof and walls of the baseline model were determined such that the deflection of the baseline model under a distributed vertical load condition is equal to the sum of the theoretical section deflections of the original box model with cut-outs. Next, to derive a hybrid bodyshell by under-frame material substitution, the material substitution method for a box-type hybrid bodyshell without cut-outs was applied to the box-type baseline model. Finally, we compared the FE simulation results of the derived hybrid bodyshells having cut-outs for various materials with the theoretical results of the suggested method, and we obtained their good correlations.