• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_2
• /
• pp.1109-1115
• /
• 2023

The shell and tube-type heat exchanger was the most utilized in industrial field because of its simple structure and wide operation conditions and so on. This study was performed to investigate the characteristics of behavior of thermal flow according to operation condition of small-sized shell and tube-type heat exchanger. The operation conditions, here, were set up to flow rate of hot air with temperature of 100℃, number of baffle and cut rate of baffle(BCR) using numerical analysis. As the results, both mean relative pressure and relative pressure drop was increased with quadratic curve in case of less than BCR 25%, however, decreased linearly in case of more than BCR 25%. The collision with first baffle by flow velocity and temperature, of hot air, respectively, was depended on BCR. Further it showed that the behaviors between flow velocity and temperature were almost similar.

• Applied Biological Chemistry
• /
• v.17 no.1
• /
• pp.42-48
• /
• 1974

Hot air thin layer drying method was studied for red pepper, Capsicum annum var. longum as the whole and cut pod states, at various temperature and air velocities. Drying curve of whole pod showed a settling down period followed by the first and second falling rate periods. By lowering the drying temperature, the first falling rate period approached to a constant rate one. Cut drying curve had simple falling rate period and also cut drying method could effectively shorten the drying time. Drying rate constant, k, was varied with time for both the drying methods and the plots of k vs. time in two methods sugested the different drying mechanisms. When an average k was taken as a constant value, the following equations; $M-M_e/M_o-M_e=e^{-0.118t}$ and $M-M_e/M_o-M_e=e(-0.342t^{0.128})$ were applicable for whole and cut drying, respectively.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.419-424
• /
• 2001

TCV(Temperature control valve by pressure compensation) controls temperature constantly, when it is sending steam or high temperature water to heating device of heat exchanger. For designing TCV, the ratio of piston and hole diameters is one of the important design parameters. Numerical analysis is carried out to elucidate the flow characteristics in the TCV with different port areas of cold and hot waters, using the k-$\epsilon$ turbulence model and Cartesian cut-cell method. Numerical results show that the exit flow rate is mainly affected by pressure distribution in the piston.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.188-191
• /
• 2001

Generally, main factors of tool damage are cutting speed, feed rate and depth of cut. The increase of those factors can cause tool breakage or worsen product quality such as machining accuracy deterioration. Those three factors are concerned with cutting force. Cutting force reaches at its maximum value when cutter blade cuts away the object directly, and it is the time when tool damages are at high probability. In this study, we detect the maximum cutting force affecting tool damage and control the maximum cutting force based on the measured peak force.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.851-856
• /
• 1997

This study is on the estimation of the tool temperature for different tool nose radius and cutting conditions in turning. The experiment has been performed in different cutting conditions such as cutting speed, feed rate, and depth of cut for the tool nose radius, 0.4R, 0.8R using SMC workpiece materials. Tool temperature is measured using thermo-couple which is embedded in the insert tip. Using a multiple linear regression method, the tool temperature can be determined as an exponential equation with cutting variables and tool nose diameters for different tool materials. The equations determined in this study show a good correlation for the cutting conditions and can be used for the tool temperature estimation. The result indicates that the tool temperature decreases for ~ncreasing the tool nose radius in general. Also, nose radius hardly influences on the tool temperature compared with cutting speed, feed rate and depth of cut.

• Journal of Mechanical Science and Technology
• /
• v.15 no.12
• /
• pp.1676-1682
• /
• 2001

This work deals with the electrical conductivity of dielectric and cobalts percentage on output parameters such as metal removal rate and surface roughness value of sintered carbides cut by wire-electrical discharge machining (WEDM). To obtain a precise workpiece with good quality, some extra repetitive finish cuts along the rough cutting contour are necessary, Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a higher metal removal rare as the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. To obtain a good surface equality without crack, 4 finish-cuts were necessary reducing fille electrical energy and the offset value.

• Journal of computational fluids engineering
• /
• v.8 no.1
• /
• pp.1-7
• /
• 2003

The present study has conducted the analysis of flows in a blower with double suction. The air handling system is for supplying air flows into a plant. The present system has a couple of impellers in axial direction for enhanced flow rate. Main interest lies on the improvements of static pressure rise and total efficiency of the system. The present treatment of the reform is to secure a spatial distance between the fan and the casing of the system and change the shape of the cut-off part. The resultant performance after the reform shows increased pressure-rise and efficiency of the system

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.31-38
• /
• 2012

In this paper, we selected primary cutting parameters that influence on surface roughness of cut bottom surface in end-milling for SM25C material. Those are overhang, depth of cut, feed rate and spindle speed. And then performed orthogonal array experiment and ANOVA by Taguchi method to determine that improved level combination of cutting parameters for betterment of working efficiency and surface roughness one of quality characteristics. And we verified a advisability of prediction model by verification test about level combination. From the results, main cutting parameter influences on surface roughness is spindle speed and the next is feed rate.

• Nuclear Engineering and Technology
• /
• v.44 no.4
• /
• pp.405-414
• /
• 2012

In this paper, we propose a reliability estimation method for DI&C systems. At the system level, a fault tree model is suggested and Boolean algebra is used to obtain the minimal cut sets. At the component level, an exponential distribution is used to model hardware failures, and Bayesian estimation is suggested to estimate the failure rate. Additionally, a binomial distribution is used to model software failures, and a recently developed software reliability estimation method is suggested to estimate the software failure rate. The overall system reliability is then estimated based on minimal cut sets, hardware failure rates and software failure rates.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.36-41
• /
• 2012

In this study, we turning plastic mold steel (STAVAX) against cutting speed, depth of cut, feed rate using whisker reinforced ceramic tool (WA1). To predict cutting force, analyze principal, radial, feed force with multi-regression analysis. Results are follows: From the analysis of variance, affected factor to cutting force feed rate, depth of cut, cutting speed in order and cutting speed was very small affect to cutting force. From multi-regression analysis, we extracted regression equation and the coefficient of determination$(R^2)$ was 0.9, 0.88, 0.856 at principal, radial and feed force. It means regression equation is significant. From the experimental verification, it was confirmed that principal, radial and feed force was predictable by regression equation.