A programmable smart charger compatible to various load conditions is proposed in this paper. Since the proposed smart charger is compatible to various mobile devices having different rated voltage and power, it is convenient for carrying and easy to standardize many kinds of battery chargers. Moreover, since it uses the input impedance and built-in PMIC (Power management IC) of the load system to recognize the connection state and specifications of load system, hardware changes of load system is not only hardly necessary but it also features no addition communication cable and easy implementation. To confirm the validity of the proposed charger, the theoretical analysis and experiment results from a prototype compatible to three load conditions 5V/1A, 5V/2A and 12V/1A are provided.
Multiple output converters (MOCs) are widely used for applications which require various levels of the output voltages due to their benefits in cost, volume, and efficiency. However, most of the MOCs developed so far can regulate only one output tightly and require as many secondary windings in the transformer as the number of the outputs. In this paper, a novel Time Division Multiple Control (TDMC) method to regulate all the outputs in high precision is proposed and applied for the multiple output battery charger based on the phase shift full bridge topology to charge a multiple number of batteries at one time. The proposed converter can charge three different kinds of batteries or same kind of batteries in different state of charges (SOCs) by using constant current/constant voltage (CC/CV) charge mode independently. At the same time it can provide an even degree of tight regulation for each output to satisfy the strict ripple requirement of the battery. The validity and feasibility of the proposed method are verified through the experiments.
The pole interaction of the line-commutated converter high-voltage direct current (HVDC) is analyzed, and a practical solution that uses a surge arrester is proposed. Jeju HVDC No. 2 is a double-monopole HVDC link that has a rated power capacity of 2 × 200 MW and was commissioned in 2012. During normal operation, Jeju HVDC No. 2 is operated in the bipolar mode to minimize the loss caused by the dedicated metallic return. However, when one pole of the inverter valve is bypassed, a commutation failure can occur in the other pole. This phenomenon is called pole interaction in this work. This pole interaction interrupts the HVDC power transfer for almost 2 s and may affect the stability of the power system. This research proposes the installation of a surge arrester at the inverter neutral, which can be an effective and practical solution for pole interaction. The HVDC system is analyzed, and the residual voltage of the surge arrester is determined. Detailed simulation using PSCAD/EMTDC demonstrates that the proposed method eliminates the pole interaction of the bipolar-operated HVDC.
In recent years, various studies have been conducted on oscillating-water-column-type wave energy converters (OWC-WECs) with multiple chambers with the objective of efficiently utilizing the limited space of offshore/onshore structures. In this study, a numerical investigation based on a numerical wave tank was conducted on single, dual, and triple OWC chambers to examine the hydrodynamic performances and the energy conversion characteristics of the multiple water columns. The boundary value problem with the Laplace equation was solved by using a numerical wave tank based on a finite element method. The validity of the current numerical method was confirmed by comparing it with the measured data in the previous experimental research. We undertook a series of numerical simulations and observed that the water column motion of sloshing mode in a single chamber can be changed into the piston motion of different phases in multiple OWC chambers. Therefore, the piston motion in the multiple chambers can generate considerable airflow at a specific resonant frequency. In addition, the division of the OWC chamber results in a reduction of the time-dependent variability of the final output power from the device. As a result, the application of the multiple chambers leads to an increase of the energy conversion performance as well as a decrease of the variability of the wave energy converter.
본 논문은 근육의 기능을 조절하는 신경말단에 전기적인 자극을 가하여 신경의 반응 정도를 측정하는 플랫폼 구현에 관한 연구로써, 전기 자극에 대한 신경반응이 가해지는 전류량, 가해지는 전류지속시간, 전극위치에 따른 반응을 측정하였다. 신격자극의 전극 위치는 표면말달 운동신경이면 어느 신경이든지 가능하고, 신격자극 양식에는 단순연축자극(Single Twitch Stimulation), 사연속자극(Train-of-four, TOF), 두 집단 발사자극(Double Burst Stimulation, DBS)이 있다. 임베디드 시스템기반으로 가기위한 저전력 MCU를 선정하고, 기본적인 신경자극반응 측정 센서의 민감도를 알아보기 위해 센서 인터페이스를 구성하여 반응정도를 측정해야 한다. 그리고 측정된 Data의 정확도를 높이기 위해 고성능의 AD Convertor 선정하여 플랫폼을 구현하였다. 또한 본 논문의 플랫폼은 의료기기용으로 개발되었기 때문에 시스템 이용자의 안전을 고려하여 전원회로 구성 시 전원 Isolation를 고려하여 설계하였다.
For the purpose of digital x-ray imaging, many materials such as $PbI_2$, $HgI_2$, TlBr, CdTe and CdZnTe have been under development for servaral years as direct converter layer. $Hgl_2$ film detector have recently been shown as one of the most promising semiconductor materials to be used as direct converters in x-ray digital radiography. This paper, the $HgI_2$ films are deposited on conductive-coated glass by screen printing, in which $HgI_2$ powder is embedded in a binder and solvent, and the slurry is used to coat the conductive-coated glass. We investigated electrical characteristic of the fabricated $HgI_2$ films. The x-ray response to radiological x-ray generator of 70Kvp using the current integration mode will be reported for screen printing films. These results indicate that $HgI_2$ detectors have high potential as new digital x-ray imaging devices for radiography.
본 논문에서는 이진 가중치 전류 기법을 이용한 고속 디지털 LDO(Low Dropout) 레귤레이터를 제안했다. 기존의 디지털 LDO는 일정량의 전류를 한 단계씩 제어하기 때문에 응답하는데 오랜 시간이 걸리며, 링잉 문제가 발생하게 된다. 이중 가중치 전류 기법은 링잉 문제를 제거함으로써 출력전압이 빠르게 안정화되도록 한다. 출력전압이 목표 전압에 안정적으로 도달하면, 디지털 LDO의 동작을 멈추는 프리즈 모드를 추가했다. 제안된 고속 응답 디지털 LDO는 출력 전원 전압이 급격히 바뀌는 시스템에서 응답속도가 느린 DC-DC 변환기와 함께 사용되어 출력전압을 빠르게 변하도록 한다. 제안된 디지털 LDO는 기존의 양방향 시프트 레지스터보다 면적이 56% 감소했고, 리플전압이 87% 감소했다. 제안된 디지털 컨트롤러는 $0.18{\mu}F$ CMOS 공정으로 제작되었다. $1{\mu}F$의 출력 캐패시터에서 정착시간이 $3.1{\mu}F$이고, 리플전압은 6.2mV 였다.
본 논문에서는 배터리 관리 시스템 (BMS)에서 2차 전지 배터리를 통해 흐르는 전류의 정밀한 측정을 위한 cascaded-of-integrator feedforward (CIFF) 구조의 단일 비트 2차 델타-시그마 모듈레이터를 제안하였다. 제안된 모듈레이터는 2개의 스위치드 커패시터 적분기, 단일 비트 비교기, 비중첩 클록 발생기 및 바이어스와 같은 주변 회로로 구현하였다. 제안된 구조는 낮은 공통 모드 입력 전압을 가지는 low-side 전류 측정 방법에 적용되도록 설계되었다. Low-side 전류 측정 방법을 사용하면 회로 설계에 부담이 줄어들게 되는 장점을 가진다. 그리고 ±30mV 입력 전압을 15비트 해상도를 가지는 ADC로 분해하기 때문에 추가적인 programmable gain amplifier (PGA)를 구현할 필요가 없어 수 mW의 전력소모를 줄일 수 있다. 제안된 단일 비트 2차 CIFF 델타-시그마 모듈레이터는 350nm CMOS 공정으로 구현하였으며 5kHz 대역폭에 대해 400의 oversampling ratio (OSR)로 95.46dB의 signal-to-noise-and-distortion ratio (SNDR), 96.01dB의 spurious-free dynamic range (SFDR) 및 15.56비트의 effective-number-of-bits (ENOB)을 달성하였다. 델타 시그마 모듈레이터의 면적 및 전력 소비는 각각 670×490㎛2 및 414㎼이다.
본 연구에서는 복권형 하이브리드 스테핑 전동기의 회전자 위치 함수로 주어지는 순시 상전류식을 유도하여 Laad Angle에 따른 순시 상전류값의 변화를 보이고, 특히 여자 펄스 인가후 ${\pi}/2$ 시점의 수닛 상전류값으로부터 회전자 위치 정보를 얻을 수 있음을 이론식 및 컴퓨터 시뮬레이션에 의해 확인하였다. 이러한 사실으로부터 복권형 하이브리드 스테핑 전동기의 폐루프 운전을 위해 회전자 위치 검출기를 사용하지 않고 전동기의 파라미터가 고려된 최적 Lead Angle이 실현된 여자 펄스를 생성시키는 제어기를 마이크로컨트롤러에 의해 구성하고 실험하였다. 구성된 제어기는 A/D 변환기, 프로그래머블 입.출력 타이머 및 전동기 속도에 대한 최적 Lead Angle 값을 갖는 변환 테이블 등의 기능을 갖는 마이크로컨트롤러와 또한 전동기의 속도와 여자 펄스 인가후 ${\pi}/2$ 시점의 순시 상전류값에 대한 정토오크 발생영역에 해당하는 Lead Angle 값을 갖는 변환 테이블을 위한 ROM 등으로 구성되어 외부 부가회로를 최소화하였으며, 전동기의 파라미터 등의 변화에 따른 제어량의 병환 테이블이 내용과 제어 S/W 에 의존함으로써 유연성을 확보하였다. 이와 같이 구성된 복권형 하이브리드 스테핑 전동기의 회전자 위 센서리스 최적 Lead Angle 시의 순시 상전류 파형과 유사한 파형을 얻음으로써 최적 Lead Angle 이 실현되었음을 확인할 수 있었다.
본 연구에서는 연료전지 중 발전효율이 50% 이상으로 가장 높고 가정용(1~10kW급) 시스템으로 필요성이 높아지고 있는 고체산화물 연료전지(SOFC, Solid Oxide Fuel Cell)에 대한 평가시스템을 설계하여 최적의 평가성능을 구현코자 하였다. 최적의 연료전지 평가시스템을 구현하기 위하여 전처리 및 반응조건 제어를 위한 온도제어모듈, 반응물에 대한 유량제어모듈, 전자부하기 등을 구현하였다. 온도제어모듈은 K형 서머커플을 사용하여 운전온도인 $750^{\circ}C$에서 $1^{\circ}C$이내의 정밀도 구현이 가능토록 설계하였고, 가스의 양이 일정하게 유지하기 위한 가습기 구조를 설계하였으며, 송풍기 및 히터의 정밀제어가 가능하도록 위상제어보드를 설계하여 적용함으로서 목표성능을 구현하였으며, 전자부하기는 방전방식으로 정전압, 정전류, 정저항 모드와 아날로그 입력과 출력모듈에 별도의 DC-DC 컨버터를 사용하여 오류를 최소화하였다. 구현한 평가시스템의 성능을 측정한 결과 스택전압은 80V에서 0.15%, 스택전류는 100A에서 0.1%의 정밀제어가 가능함을 확인하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.