• Composites Research
• /
• v.14 no.3
• /
• pp.18-31
• /
• 2001

Interfacial and microfailure properties of the modified steel, carbon and glass fibers/cement composites were investigated using electro-pullout test under tensile and compressive tests with acoustic emission (AE). The hand-sanded steel composite exhibited higher interfacial shear strength (IFSS) than the untreated and even neoalkoxy zirconate (Zr) treated steel fiber composites. This might be due to the enhanced mechanical interlocking, compared to possible hydrogen or covalent bonds. During curing process, the contact resistivity decreased rapidly at the initial stage and then showed a level-off. Comparing to the untreated case, the contact resistivity of either Zr-treated or hand-sanded steel fiber composites increased to the infinity at latter stage. The number of AE signals of hand-sanded steel fiber composite was much more than those of the untreated and Zr-treated cases due to many interlayer failure signals. AE waveforms for pullout and frictional signals of the hand-sanded composite are larger than those of the untreated case. For dual matrix composite (DMC), AE energy and waveform under compressive loading were much higher and larger than those under tensile loading, due to brittle but well-enduring ceramic nature against compressive stress. Vertical multicrack exhibits fur glass fiber composite under tensile test, whereas buckling failure appeared under compressive loading. Electro-micromechanical technique with AE can be used as an efficient nondestructive (NDT) method to evaluate the interfacial and microfailure mechanisms for conductive fibers/brittle and nontransparent cement composites.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.4
• /
• pp.117-124
• /
• 2009

The purpose of the study was to improve quality of high volume fly ash concrete. The study evaluated on the possibility of early quality improvement of high volume fly ash concrete with early strength gain admixture ('GA' below) developed by the preceding research. The study regarded applying naphthalene admixture ('NA' below) to mix proportion substituting FA 15 % to be plain. In the event of substituting FA 20, 25 and 30 %, the study compared engineering properties of concrete with plain by applying GA. Because of features of fresh concrete, fluidity falls down when GA is applied. Therefore, its use amount shall be increased. Only, in W/B 60 %, it was beneficial since slump loss was reduced about 35~70 mm than plain. The study could see that AE use should be increased proportionally since air content was reduced by coming from AE absorption operation of unburned coal content included in FA according to an increase in the amount of FA use. Reduction effect of bleeding could be anticipated since the amount of bleeding appeared at least in FA 20 %. Because of hardened concrete, time of setting appeared in the same level as plain when GA was applied. Therefore, it is judged that delay of setting can be reduced. In compressive strength, the study could check the same strength development as plain when GA was applied, having nothing to do with W/B and curing temperature. However, it is thought that we shall pay attention to GA use in the event of FA 30 % substitution. Freezing and melting resistance had less early value than plain. However, it is judged that there will be no problem of frost resistance since there is no a large difference between freezing and melting resistance and plain in overall. In accelerated neutralization, it was analyzed that a problem of weakening in neutralization appointed as a demerit when FA was applied in mass in proportion with GA use could be settled to some extent.

• Restorative Dentistry and Endodontics
• /
• v.32 no.2
• /
• pp.111-120
• /
• 2007

The purpose of this study is to evaluate the effects of surface treatment and composition of reinforcement material on fracture strength of fiber reinforced composite inlay bridges. The materials used for this study were I-beam, U-beam TESCERA ATL system and ONE STEP(Bisco, IL, USA). Two kinds of surface treatments were used; the silane and the sandblast. The specimens were divided into 11 groups through the composition of reinforcing materials and the surface treatments. On the dentiform, supposing the missing of Maxillary second pre-molar and indirect composite inlay bridge cavities on adjacent first pre-molar disto-occlusal cavity, first molar mesio-occlusal cavity was prepared with conventional high-speed inlay bur. The reinforcing materials were placed on the proximal box space and build up the composite inlay bridge consequently. After the curing, specimen was set on the testing die with ZPC. Flexural force was applied with universal testing machine (EZ-tester; Shimadzu, Japan). at a cross-head speed of 1 mm/min until initial crack occurred. The data was analyzed using one-way ANOVA/Scheffes post-hoc test at 95% significance level. Groups using I-beam showed the highest fracture strengths (p<0.05) and there were no significant differences between each surface treatment (p>0.05) Most of the specimens in groups that used reinforcing material showed delamination. 1. The use of I-beam represented highest fracture strengths (p<0.05) 2. In groups only using silane as a surface treatment showed highest fracture strength, but there were no significant differences between other surface treatments (p>0.05). 3. The reinforcing materials affect the fracture strength and pattern of composites inlay bridge. 4 The holes at the U-beam did not increase the fracture strength of composites inlay bridge.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.24 no.6
• /
• pp.1026-1038
• /
• 1995

Although aloe lost a lot of its previous popularity in modern clinical uses as medicine numerous scientific researches still have claimed the beneficial properties(curing and general tonic effect) of aloe gel. Whereas considerable contradictory reports have helped to confuse the aloe gel issue and continually aroused controversy about aloe gel efficacy. However health food, cosmetic and medicinal products made from aloe gel are widely available in the world market especially in U.S.A. so the growing of Aloe plant and the processing of A. vera gel have become big industries in some countries. In some previous papers the salicylic acid, one of the common trace gel components, was thought to have an analgetic and antinflammatory effect. Large amount of Mg ion in the gel was suggested to act as anesthetic, Mg-lactate as antihistamic, and Aloctin A(a glycoprotein) as wound healer by promoting the cell growth. The carboxypeptidase and bradykinase activity in the gel were proposed to have the pain relieving and antiinflammatory effect. But any of thes etheories concerining the physiological action of the trace gel components has not been demonstrated by modern pharmacology, and failed to be supported by clinical research. It was suggested by some research workers that trace amount of anthraquinone compounds in the gel play an important role to act as false substrate inhibitors for PG and TX production(antiprostanoid effect), by which, they believed, inflammation, burn and frostbite, and infected wound could be healed. This hypothesis has not been substantiated. Butthe suggested antimicrobial action, antidiabetic, and antidotic effect of aloe gel are likely to be attributed to the trace anthraquinone compounds. In a lot of recent experimental reports it has been claimed that aloe gel polysaccharides(acetylglucomannan, acetylmannan, and glycoprotein) have the antimicrobial, antinflammatory, antitumour, and infected wound healing effect by immunoenhancement. It is hoped that these effects will be soon documented in clinical studies, then the controversy on aloe gel beneficial effect will cease. In the 30 days subchronic toxicity test the lowest observed adverse effect level of acemannan(acetylmannan) on dog was 5.0 mg/kg, IP. But the aloe gel is generally agreed to be harmless and non toxic even for the internal use such as health food. In the case of idiosynrasy one must keep the delayed type hypersensitivity reaction of aloe gel in mind. In conclusion it seem to be impossible to simply refuse a lot of evidences made by research workers who have claimed aloe gel's beneficial effects and to deny the fact that there had been long therapeutic histories of Aloe plants.

• Journal of Animal Science and Technology
• /
• v.50 no.3
• /
• pp.391-400
• /
• 2008

Odor management is significantly concerned with sustainable livestock production because odor nuisance is a primary cause for complaint to neighbors. This study was conducted to measure the concentration of odorous compounds, odor intensity, and odor offensiveness at unit process in animal waste treatment facility combined composting and methane fermentation process by an instrumental analysis and direct olfactory method. Ammonia, sulfur-containing compounds, and volatile fatty acid were analyzed at each process units and boundary area in summer and winter, respectively. Higher concentration of odorants occurred in the summer than in the winter due to high ambient temperature. The maximum concentration of odorants was detected in composting pile when mixed manure was being turned followed by inlet, curing, outlet, and screen & packing process. Highest concentration of detected odorous compounds was ammonia ranging from 3.4 to 224.7 ppm. Among the sulfur-containing compounds measured, hydrogen sulfide was a maximum level of 2.3 ppm and most of them exceeded reported odor detection thresholds. Acetic acid was the largest proportion of VFA generated, reaching a maximum of 51 to 89%, followed by propionic and butyric acid at 1.9 to 35% and 1.8 to 15%, respectively. Malodor assessment by a human panel appeared a similar tendency in instrumental analysis data. Odor quotient for predicting major odor-causing compounds was calculated by dividing concentrations measured in process units by odor detection thresholds. In the composting process, hydrogen sulfide, ammonia, dimethyl sulfide, and methyl mercaptan were deeply associated with odor-causing compounds, while the major malodor compounds in the inlet process were methyl mercaptan, hydrogen sulfide, and butyric acid.

• Restorative Dentistry and Endodontics
• /
• v.32 no.4
• /
• pp.377-384
• /
• 2007

Present tooth bonding system can be categorized into total etching bonding system (TE) and self-etching boding system (SE) based on their way of smear layer treatment. The purposes of this study were to compare the effectiveness between these two systems and to evaluate the effect of number of themocycling on microleakage of class V composite resin restorations. Total forty class V cavities were prepared on the single-rooted bovine teeth and were randomly divided into four experimental groups: two kinds of bonding system and another two kinds of thermocycling groups. Half of the cavities were filed with Z250 following the use of TE system, Single Bond and another twenty cavities were filled with Metafil and AQ Bond, SE system. All composite restoratives were cured using light curing unit (XL2500, 3M ESPE, St. Paul, MN, USA) for 40 seconds with a light intensity of $600mW/cm^2$. Teeth were stored in distilled water for one day at room temperature and were finished and polished with Sof-Lex system. Half of teeth were thermocycled 500 times and the other half were thermocycled 5,000 times between $5^{\circ}C$ and $55^{\circ}C$ for 30 second at each temperature. Teeth were isolated with two layers of nail varnish except the restoration surface and 1 mm surrounding margins. Electrical conductivity (${\mu}A$) was recorded in distilled water by electrochemical method. Microleakage scores were compared and analyzed using two-way ANOVA at 95% level. From this study, following results were obtained: There was no interaction between variables of bonding system and number of thermocycling (p = 0.485). Microleakage was not affected by the number of thermocycling either (p = 0.814). However, Composite restoration of Metafil and AQ Bond, SE bond system showed less microleakage than composite restoration of Z250 and Single Bond, TE bond system (p = 0.005).

• Journal of the Korean Geosynthetics Society
• /
• v.20 no.2
• /
• pp.23-33
• /
• 2021

In Korea, many reservoirs have been built for the purpose of solving the food shortage problem and supplying agricultural water. However, the current 75.6% of the reservoirs are in serious aged as more than 50 years have passed since the year of construction. In the case of such an aging reservoir, the stability due to scour and erosion inside the reservoir is very reduced, and if concentrated rainfall due to recent abnormal weather occurs, the aging reservoir may collapse, leading to a lot of damage to property and human life. Accordingly, each agency that manages aging reservoirs uses Ordinary Portland Cement (OPC) as an injection material and applies the grouting method. However, in the case of OPC, it may deteriorate over time and water leakage may occur again. And there are environmental problems such as consumption of natural resources and generation of greenhouse gases. So, there is a need to develop new materials and methods that can replace the OPC. In this study, an laboratory test and analysis were performed on the grout material developed to induce a curing reaction similar to that of OPC by recycling power plant byproduct. In addition, test in the field such as electric resistivity survey, Standard Penetration Test (SPT), and field permeability test were performed to analyzed to reinforcement effect and determine the possibility of using instead of OPC. As a results of the test, in the case of recycled power plant byproduct, the compressive strength was 2.9 to 3.2 times and the deformation modulus was 2.3 to 3.3 times higher, indicating that it is excellent in strength and can be used instead of OPC. And it was analyzed that the N value of the reservoir was increased by 1~2, and the coefficient of permeability (k) decreased to the level of 8.9~42.5%. showing sufficient reinforcing effect in terms of order.

• Journal of the Korean Society of Tobacco Science
• /
• v.24 no.1
• /
• pp.67-73
• /
• 2002

In light of addressing consumer health concern, coping with anti-tobacco movement, and promoting new product, tobacco industry is actively pursuing to make a new generation of cigarettes with low tar and nicotine deliveries, and less harmful substances. Low tar and low nicotine cigarettes increases their market shares dramatically world wide, especially in KT&G, multinational tobacco companies, EU countries, even in China regulated by CNTC to set up yearly target to lower tar and nicotine deliveries. On the other hand, to design a new cigarette with reduced harmful substances begins to gain speed. The "modified Hoffmann list" publishes thirty plus substances in tobacco leaf and main smoke stream, which is the prime suspect causing health problems. Various ways and means are developed to reduce such components including new tobacco breeds, new curing method, tobacco leaf treatment before processing, selected filtration system, innovated casing system to reduce free radicals, as well as some non conventional cigarette products. In TSRC held this year, the main topic is related to reduce tobacco specific nitrosamines in tobacco leaf. The new generation of cigarette is in the horizon. It still needs a lot help to produce commercial products with satisfied taste and aroma characters. The flavor industry is not regulated by many governments demanding which ingredients might or might not be for tobacco use. However, most of the cigarette companies self impose a list of ingredients to guide flavor suppliers to design flavors. Unfortunately, the number of ingredients in those lists is getting shorter every year. It is understandable that the health is not the only reason. Some cigarette companies are playing safe to protect the company from potential lawsuit, while others are just copying from their competitors. Moreover, it is obvious that it needs more assistance from casings and flavors to design new generation of cigarettes with missing certain flavor components in tobacco leaf and main smoke stream. These flavor components are either non-existed or at lower level at new form of cured tobacco leaf or filtered in the main smoke stream along with reduced harmful substances. The use of carbon filters and other selected filtration system poses another tough task for flavor system design. Specific flavor components are missing from the smoke analysis data, which brings a notion of "carbon taste" and "dryness" of mouth feel. It is ever more demanded by cigarette industry to flavor suppliers to produce flavors as body enhancer, tobacco notes, salivating agents, harshness reducer, and various of aromatic notes provided they are safe to use. Another trend is that water based flavor or flavor with reduced ethanol as solvent is gaining popularity. It is preferred by some cigarette companies that the flavor is compounded with all natural ingredients or all ingredients should he GMO free. The new generation of cigarettes demands many ways of new thinking process. It is also vital for tobacco industry. It reflects the real needs for the consumers that the cigarette product should be safe to use as well as bearing the taste and aroma characters smokers always enjoyed. An effective tobacco flavor system is definitely a part of the equation. The global trend of tobacco industry is like trends of any other industries lead by consumer needs, benefited with new technology availability, affected by the global economy, and subjected for various rules and regulations. Anti-tobacco organizations and media exceptionally scrutinize cigarette, as a legal commercial product. Cigarette is probably the most studied commercial product for its composition, structure, deliveries, effects, as well as its new developmental trend. Therefore, any new trend of cigarette development would be within these boundaries. This paper is trying to point out what it would be like for tobacco industry in the next few yews and what concerns the tobacco industry. It focuses mostly on the efforts to produce safer cigarettes. It is such a vital task for the tobacco industry and its affiliate industries such as cigarette papers, filters, flavors, and other materials. The facts and knowledge presented in this paper might be well known for the public. Some of the comments and predictions are very much personal opinion for a further discussion.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.38 no.4
• /
• pp.189-195
• /
• 2022

Purpose: For orthodontic bracket bonding, light curing resin cement is widely used because the process is convenient, and it can be polymerized at the desired time. This study compared the difference of bonding strength of orthodontic resin cement according to storage condition. Materials and Methods: After acid etching the bovine enamel surface with 37% phosphoric acid, 15 orthodontic brackets for mandible incisors were bonded with Ortho Connect and Orthomite LC according to following three conditions; 1) Immediate after 4℃ refrigeration for 3 months (IR), 2) One day room temperature after 4℃ refrigeration for 3 months (OR), 3) Room temperature for 3 months (RT). The shear bond strength was measured with a universal material tester and failure pattern of the specimen was observed. Two-way ANOVA and One-way ANOVA were used at the 95% significance level. Results: Ortho Connect that was applied immediately after refrigeration showed the maximum shear bond strength. Orthomite that was applied immediately after refrigeration showed the lowest shear bond strength, and the group stored at room temperature for three months showed the highest shear bond strength, and the difference between the two groups was significant. Conclusion: Ortho Connect can be used without worrying about bond strength even if it is used immediately after refrigeration, but Orthomite should be kept at room temperature sufficiently after refrigeration.

• Journal of the Korea Institute of Building Construction
• /
• v.24 no.2
• /
• pp.181-191
• /
• 2024

In the realm of cement manufacturing, concerted efforts are underway to mitigate the emission of greenhouse gases. A significant portion, approximately 60%, of these emissions during the cement clinker sintering process is attributed to the decarbonation of limestone, which serves as a fundamental ingredient in cement production. Prompted by these environmental concerns, there is an active pursuit of alternative technologies and admixtures for cement that can substitute for limestone. Concurrently, initiatives are being explored to harness technology within the cement industry for the capture of carbon dioxide from industrial emissions, facilitating its conversion into carbonate minerals via chemical processes. Parallel to these technological advances, economic growth has precipitated a surge in construction activities, culminating in a steady escalation of construction waste, notably waste concrete. This study is anchored in the innovative production of calcium silicate cement clinkers, utilizing finely powdered waste concrete, followed by a thorough analysis of their mineral phases. Through X-ray diffraction(XRD) analysis, it was observed that increasing the substitution level of waste concrete powder and the molar ratio of SiO₂ to (CaO+SiO₂) leads to a decrease in Belite and γ-Belite, whereas minerals associated with carbonation, such as wollastonite and rankinite, exhibited an upsurge. Furthermore, the formation of gehlenite in cement clinkers, especially at higher substitution levels of waste concrete powder and the aforementioned molar ratio, is attributed to a synthetic reaction with Al₂O₃ present in the waste concrete powder. Analysis of free-CaO content revealed a decrement with increasing substitution rate of waste concrete powder and the molar ratio of SiO₂/(CaO+SiO₂). The outcomes of this study substantiate the viability of fabricating calcium silicate cement clinkers employing waste concrete powder.