• Tribology and Lubricants
• /
• 제39권3호
• /
• pp.111-117
• /
• 2023

This paper presents an experimental investigation of the tribological characteristics of PTFE composites filled with nano CuO particles under low sliding speed and load. All the specimens were prepared by sintering. Before sintering, the mixture of PTFE powder and CuO particles were mixed by a high-speed mixer using CuO volume fractions of 0.2 vol. % and 5 vol. %. Each mixture was sintered at 350 ℃ for 30 min on the steel disk. We conducted ball-on-disk sliding test an hour using a steel ball against PTFE composites, including pure PTFE. The load and sliding speed used was 2 N and 0.01 m/s, respectively. Adding nano CuO particles increases the friction coefficient because of the abrasiveness of hard nano CuO particles. The highest coefficient of frictions was obtained from 5 vol. % CuO. Conversely, the lowest wear of the composites was obtained from the 5 vol. % CuO nanocomposite. This study reveals that the addition of nano CuO particles can lower the wear of PTFE, despite an increase in the coefficient of friction. However, the coefficient friction is still moderate compared to other engineering polymers. In addition, the amount of CuO nano particles has to be optimized to reduce friction and wear at the same time.

• 한국재료학회지
• /
• 제27권4호
• /
• pp.221-228
• /
• 2017

Various morphologies of copper oxide (CuO) have been considered to be of both fundamental and practical importance in the field of electronic materials. In this study, using Cu ($0.1{\mu}m$ and $7{\mu}m$) particles, flake-type CuO particles were grown via a wet oxidation method for 5min and 60min at $75^{\circ}C$. Using the prepared CuO, AlN, and silicone base as reagents, thermal interface material (TIM) compounds were synthesized using a high speed paste mixer. The properties of the thermal compounds prepared using the CuO particles were observed by thermal conductivity and breakdown voltage measurement. Most importantly, the volume of thermal compounds created using CuO particles grown from $0.1{\mu}m$ Cu particles increased by 192.5 % and 125 % depending on the growth time. The composition of CuO was confirmed by X-ray diffraction (XRD) analysis; cross sections of the grown CuO particles were observed using focused ion beam (FIB), field emission scanning electron microscopy (FE-SEM), and energy dispersive analysis by X-ray (EDAX). In addition, the thermal compound dispersion of the Cu and Al elements were observed by X-ray elemental mapping.

• 한국주조공학회지
• /
• 제17권5호
• /
• pp.480-487
• /
• 1997

Particle reinforced metal matrix composites(MMCs) via a centrifugal spray-cast deposition(CSD) process were fabricated by injecting second phase particles($Al_2O_3$<40${\mu}m$, W<17.3${\mu}m$) into copper melt on the atomizing disc. Compositing modes were investigated by combining microstructures and mathematical modeling between Cu droplets and the reinforced particles injected. The $Cu/W_P$ powders were shown that the W particles penetrate and get embedded in the Cu droplets. It is considered that the W particles composite preferentially in Cu melt on the atomizing disc. On the other hand, the $Al_2O_3$, particles did not penetrate into the Cu droplets on the atomizing disc but get attached in surface of Cu droplets during the flight. It is considered that the compositing may be attained in the flight distance which the relative velocity between Cu droplet and $Al_2O_3$, particle is maximum. The microstructure of the $Cu/W_P$ and the $Cu/(Al_2O_3)_p$ composite preform was strongly influenced by compositing modes of droplets, and after subsequent deposition it was comprised as it is called the dispersed type and the cell type of microstructure, respectively.

• 한국전기전자재료학회논문지
• /
• 제37권1호
• /
• pp.63-67
• /
• 2024

In this study, we successfully synthesized copper oxide (Cu₂O) particles through a hydrothermal method at a relatively low temperature (150℃). The synthesis involved the precise control of molar concentrations of NaOH. Notably, Cu₂O particles were effectively synthesized when NaOH concentrations of 0.15 M and 0.20 M were utilized. While attempts were made at different molar concentrations, the synthesis of pure Cu₂O particles was only achieved at concentrations of 0.15 M and 0.20 M. In this experimental investigation, Cu₂O synthesized under these specific conditions exhibited absorption characteristics within the wavelength range of 640 to 570 nm, consistently exhibiting a band gap energy of 1.9 eV. These Cu₂O particles, characterized by their small band gap energy and straightforward synthetic method, hold significant promise for various applications including semiconductors and solar cells.

• 한국재료학회지
• /
• 제13권8호
• /
• pp.524-530
• /
• 2003

In order to prepare the uniform copper particles from copper sulfate solution by using hydrazine as a reduction agents, the reduction behavior of copper particles from copper sulfate was investigated in detail at room temperature by the observation of reaction products. The effects of $NH_4$OH and $Na_4$$P_2$$O_{7}$ on the formation of uniform copper particles were discussed. ($NHCu_3$)$_4$$SO_4$was completely formed at over pH 11 by adding $NH_4$OH in copper sulfate solution. The fine $Cu_2$O with the particle size of 50 nm was produced in the initial reduction process of (NH$Cu_3$)$_4$$SO_4$solution with $Na_4$$P_2$$O_{ 7}$ and then the Cu$_2$O was converted into copper particles by inserting additional hydrazine. When Cu(NH$_3$)$_4$SO$_4$solution with $Na_4$$P_2$$O_{ 7}$ was reduced at $80^{\circ}C$ by hydrazine, the highly dispersed copper particles with the particle size of about 0.8 $\mu\textrm{m}$ was obtained.

• 한국분말재료학회지
• /
• 제14권2호
• /
• pp.123-126
• /
• 2007

In this work, the dispersion behavior of $Y_2O_3$ particles in binary aluminum (Al)-copper (Cu) cast alloy was investigated with respect to Cu contents of 20 (hypoeutertic), 33 (eutectic) and 40 (hypereutectic) wt.%. In cases of hypo and hypereutectic compositions, SEM images revealed that the primary Al and ${\theta}$ phases were grown up at the beginning, respectively, and thereafter the eutectic phase was solidified. In addition, it was found that some of $Y_2O_3$ particles can be dispersed into the primary Al phase, but none of them are is observed inside the primary 6 phase. This different dispersion behavior of $Y_2O_3$ particles is probably due to the difference in the val- ues of specific gravity between $Y_2O_3$ particles and primary phases. At eutectic composition, $Y_2O_3$ particles were well dispersed in the matrix since there is few primary phases acting as an impediment site for particle dispersion during solidification. Based on the experimental results, it is concluded that $Y_2O_3$ particles are mostly dispersed into the eutectic phase in binary Al-Cu alloy system.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.225-228
• /
• 1997

YBa$_2$Cu$_3$O$_{x}$ samples with different amounts of $Y_2$BaCuO$_{5}$ were prepared by MPMG (Melt Powder Melt Growth) method. The effects on the size of initial particles and Ag addition for $Y_2$BaCuO$_{5}$ distribution in YBa$_2$Cu$_3$O$_{x}$ were invesgated. The samples prepared by the melting process usually have large grains up to several ㎣ and precipitates of $Y_2$BaCuO$_{5}$. The distribution of the $Y_2$BaCuO$_{5}$ particles in the samples depends on the size of initial particles and the amounts of Ag addition.Ag addition.

• 한국분말재료학회지
• /
• 제11권2호
• /
• pp.171-178
• /
• 2004

Effects of liquid phase and reinforcing particle morphology on the sintering of Al-6 wt％Cu-10 vol％ $Al_2O_3$ or SiC particles were studied in regards to densification, structure and transverse rupture properties. The Al-Cu liquid phase penetrated the boundaries between the aluminum matrix powders and the interfaces with reinforcing particles as well, indicating a good wettability to the powders. This enhanced the densification during sintering and the resulting strength and ductility. Since most of the copper added, however, was dissolved in the liquid phase and formed a brittle $CuAl_2$ phase upon cooling rather than alloyed with the aluminum matrix, the strengthening effect by the copper was not fully realized. Reinforcing particles of agglomerate type were found less suitable for the liquid phase sintering than solid type particles. $Al_2O_3$ and SiC particles protluced little difference on the sintering behavior but their size had a large effect. Repressing of the sintered composites increased density and bending properties but caused debonding at the matrix-particle interfaces and also fracturing of the particles.

• 한국재료학회지
• /
• 제15권4호
• /
• pp.263-270
• /
• 2005

In order to prepare the uniform copper particles from copper chloride solution, the reduction behavior of copper particles from copper chloride and the effects of reduction agent and dispersing agent was investigated. In the case that 2.56 M of $C_6H_8O_6$ was used as a reduction agent, the highly dispersed Cu particles with sharp size distribution were generated from 0.96M of copper chloride solution, and the size of Cu particles was $6\~10\;{\mu}m$. To form $Cu(NH_3)_4Cl_2$ complex solution, $NH_4OH$ was added in the copper chloride solution before the reductive reaction of Cu ion. The generated Cu particles have a two kind of shape, spherical and rod-like. In the case that $N_2H_4{\cdot}H_2O$ was used as a reduction agent, the very fine spherical Cu particles with the size of $0.2\~0.5\;{\mu}m$ was obtained. Arabic gum as a dispersing agent was more effective than $Na_4P_2O_7{\cdot}10H_2O$.

• 대한환경공학회지
• /
• 제31권12호
• /
• pp.1069-1074
• /
• 2009

본 연구에서는 CuO와 ZnO의 입자 크기가 옥수수의 성장과 토양 미생물 군집에 미치는 독성을 microcosm 실험을 통하여 살펴보았다. 나노 입자는 micro 입자에 비해 옥수수의 biomass를 약 30% 감소시켜 나노 입자가 옥수수의 성장을 저해하는 것으로 나타났다. 토양 미생물 활성 지표인 Dehydrogenase activity는 CuO 나노 입자에서는 낮게 나타났으나 ZnO 나노 입자에서는 높게 나타났다. Biolog test 결과, CuO 나노 입자와 ZnO micro 입자에서 토양 미생물 다양성이 감소하는 것으로 나타났다. 그러므로, metal oxide의 나노 입자가 micro 입자보다 항상 토양 미생물의 활성 및 다양성에 더 유해한 영향을 나타내는 것은 아니라고 판단된다.