This study reports the effects of $H_2S$ gas concentration on the properties of $Cu_2ZnSnS_4(CZTS)$ thin films. Specifically, sulfurization process with low $H_2S$ concentrations of 0.05% and 0.1%, along with 5% $H_2S$ gas, was studied. CZTS films were directly synthesized on Mo/Si substrates by chemical bath deposition method using copper sulfate, zinc sulfate heptahydrate, tin chloride dihydrate, and sodium thiosulfate pentahydrate. Smooth CZTS films were grown on substrates at optimized chemical bath deposition condition. The CZTS films sulfurized at low $H_2S$ concentrations of 0.05 % and 0.1% showed very rough and porous film morphology, whereas the film sulfurized at 5% $H_2S$ yielded a very smooth and dense film morphology. The CZTS films were fully crystallized in kesterite crystal form when they were sulfurized at $500^{\circ}C$ for 1 h. The kesterite CZTS film showed a reasonably good room-temperature photoluminescence spectrum that peaked in a range of 1.4 eV to 1.5 eV, consistent with the optimal bandgap for CZTS solar cell applications.
Diffusion speed of Cu metal fine particle is fast better than CuO, so it will promote grain growth in sintering. In this paper, the influence on substituting Cu fine particle for CuO of NiCuZn ferrite with basic composition (N $i_{0.204}$C $u_{0.204}$Z $n_{0.612}$$O_{1.02}$)F $e_{1.98}$$O_{2.98}$ has been investigated with varying Cu/CuO ratio. The perfect spinel structure of sintered specimen at 90$0^{\circ}C$ was confirmed by the analysis of XRD patterns. The best condition was obtained when the ratio of Cu/CuO was 60%, and the permeability was 1100 and Ms was 87 emu/g in this condition. Cu has influenced on grain growth in sintering, substituting Cu fine particle for CuO could lower sintering temperature over the 3$0^{\circ}C$. After sintering, substituting Cu performed as good as CuO.s CuO.s CuO.
A novel powder processing technique for the preparation of copper activated zinc sulfide (ZnS:Cu,Al) phosphor by combustion process has been proposed. Exothermic reaction between dissolved copper nitrate and carbohydrazide give small-sized particles in presence of alkali metal halides at lower temperature than the traditional method of preparation. This new route takes less than five minutes and requires much less energy. The optical and luminescence characteristics of ZnS:Cu,Al phosphor thus prepared were found to be enhanced significantly. Carbohydrazide acted as fuel at $500^{\circ}C$ with rapid heating and then the phosphors obtained were heated at $900^{\circ}C$ in an inert atmosphere for 3hrs to get better luminescent properties.
The Transactions of the Korean Institute of Electrical Engineers C
/
v.48
no.5
/
pp.349-353
/
1999
In this paper, to fabricate the AC power electroluminescent device (PELD) with high brightness, new structure that constructed single emissive layer between electrodes was proposed. Dielectric and phosphor material structure that constructed single emissive layer between electrodes was proposed. Dielectric and phosphor material were BaTiO3 and ZnS:Cu respectively. Fabricated AC power EL devices were estimated by optical and electrical properties of EL spectrum, brightness, CIE coordinate system, transferred charge density and EL emission wave in time domain. With above results, we found that brightness of newly proposed AC powder EL power EL device was 2754 cd/m2 at 100V, 400 Hz and compared with conventional device structure.
Recently, thin-film solar cells of Cu(In,Ga)$Se_2$(CIGS) have reached a high level of performance, which has resulted in a 19.9%-efficient device. These conventional devices were typically fabricated using chemical bath deposited CdS buffer layer between the CIGS absorber layer and ZnO window layer. However, the short wavelength response of CIGS solar cell is limited by narrow CdS band gap of about 2.42 eV. Taking into consideration the environmental aspect, the toxic Cd element should be replaced by a different material. It is why during last decades many efforts have been provided to achieve high efficiency Cd-free CIGS solar cells. In order to alternate CdS buffer layer, ZnS buffer layer is grown by using chemical bath deposition(CBD) technique. The thickness and chemical composition of ZnS buffer layer can be conveniently by varying the CBD processing parameters. The processing parameters were optimized to match band gap of ZnS films to the solar spectrum and exclude the creation of morphology defects. Optimized ZnS buffer layer showed higher optical transmittance than conventional thick-CdS buffer layer at the short wavelength below ~520 nm. Then, chemically deposited ZnS buffer layer was applied to CIGS solar cell as a alternative for the standard CdS/CIGS device configuration. This CIGS solar cells were characterized by current-voltage and quantum efficiency measurement.
Chemical analyzes were carried out the samples from roadsides of the Gwangju city. The purpose of this research is to investigate the concentrations and distribution patterns of heavy metals due to urbanization and industrialization in the Gwangju city This study area is not significantly contaminated based on the concentrations of Cd, Cu, Fe, Mn, Pb and Zn. However, the concentrations of the chemical elements analyzed are locally higher than those of serious contamination level indicated by Ministry of environment. The dust pH is in the rage of 5.60-7.09 and was generally neutral, and there are no difference in pollution area and nonpollution area. Chemical analyses utilized are dilution by 0.1N HCl. In result of analysis by the method using 0.1N HCl, concentrations of Cd and Cu are a little high in Gwangchondong of Seo-Gu. Concentrations of Mn and Pb are a little high in Buk-Gu and Nam-gu, and Concentrations of Zn are generally higher than average of soils. Zn, in the study area, keeps polluting greatly as Zn concentration of average is 150.9ppm. All of P.I values are lower than 1, it means heavy metal pollution is not serious.
Journal of the Korea Academia-Industrial cooperation Society
/
v.13
no.8
/
pp.3806-3813
/
2012
The coastal environment is affected by Cu and Zn contamination through diverse routes, including antifouling agents, industrial wastewater, and domestic activities. In this study, Crassostrea gigas and Littorina brevicula were used to examine the distributions of Cu and Zn, which are related to the increase in the use of new antifouling agents that have been used for ships since the TBT ban in 2003. The average Cu and Zn concentrations in the samples were 231.8 ${\mu}g/g$ and 492.6 ${\mu}g/g$, respectively. Both the Cu and Zn concentrations were highest in the shipyard samples, followed by the harbor sample for Cu and the industrial area sample for Zn. The results indicated that the Cu concentration was affected by the antifouling agents, and the Zn concentration was affected by both the antifouling agents and industrial wastewater. The areas that need intensive control to address the Cu and Zn contamination in major Korean coasts were identified.
$Cu_{1.8}Zn_{1.2}(Sn_{1-x}Ge_x)S_4$ (CZTGeS) nanocrystals were mechanochemically synthesized from elemental precursor powders without using any organic solvents and any additives. The composition of CZTGeS nanocrystals were systematically varied with different Ge mole fraction (x) from 0.1 to 0.9. The XRD, Raman spectroscopy, high-resolution TEM, and diffuse reflectance studies show that the as-synthesized CZTGeS nanocrystals exhibited consistent changes in various structural and optical properties as a function of x, such as lattice parameters, wave numbers for $A_1$ Raman vibration mode, interplanar distances (d-spacing), and optical bandgap energies. The bandgap energy of the synthesized CZTGeS nanocrystals gradually increases from 1.40 to 1.61 eV with increasing x from 0.1 to 0.9, demonstrating that Ge-doping is useful means to tune the bandgap of mechanochemically synthesized nanocrystals-based kesterite thin-film solar cells. The preliminary solar cell performance is presented with an efficiency of 3.66%.
Kim, Young-Oh;Yoo, Hyung-Yul;Lee, Jae-Hyung;Ki, No-Suk;Hwang, In-Dam
Journal of Preventive Medicine and Public Health
/
v.21
no.2
s.24
/
pp.320-328
/
1988
This study was carried out to investigate the heavy metal contents and their correlationship between paddy soil and brown rice near the Kum-River area. In this study, eighty soil samples and forty brown rice samples were taken from the paddy soil. The contents of heavy metals were measured by flame atomic absorption spectrophotometry. The results were as follows: 1. The average contents of soluble heavy metals in surface soil were Cd 0.19, Cu 15.31, Zn 18.10 and Pb 9.08 ppm. The average contents of soluble heavy metals in subsurface soil were Cd 0.19, Cu 14.52, Zn 17.75 and Pb 8.11 ppm. There was no statistically significant difference between the two layers. 2. The contens of Cu, Zn and Pb of Taejeon(S6) and Cd of Sinbyung(S5) in surface soil were higher than those of other areas. The contents of Cd and Cu of Taejeon(S6) and Zn and Pb of Kumnam(S3) in brown rice were higher than those of other areas and four heavy metals in soil and brown rice of Simchon(S7) were lower than those of other areas. 3. The ratio of soluble contents(Cd:Cu:Zn:Pb) in surface soil was 1:79:93:47, that of soluble contents in subsurface soil was 1:76:94:43, and that of total contents in brown rice was 1:84:294:12. 4. The correlationship of the content between soluble heavy metals in surface(0-15 cm depth) soil total heavy metals in brown rice was found to be order of Cd>Cu>Zn>Pb. The correlationship of the content between soluble heavy metals in subsurface(20-30 cm depth) soil and total heavy metals in brownricewasfoundtobeorderofcu>Cd>Zn>Pb.
Powder type electroluminescent device(P-ELD) in this study was prepared by printing method. P-ELDs were basically composed of phosphor, insulator and transparent conducting layer. The phosphor powder was prepared by sintering the mixture of ZnS as a host, Cu as an activator, and NaCl as a flux for co-activator and enhancement of growth of the phosphor particles. The phosphor layer was made by printing the paste of the cyanoethylpullan as a binder and the ZnS system phosphor powder. In order to evaluate the luminescence characteristics of ZnS P-ELD, applied voltage - luminance(V-L), frequency-luminance(f-L), and relative luminance spectra(L- .lambda.) characteristics were measured. The experimental results show that luminance increased with increasing the applied voltage and frequency. It can be explained in terms of the potential barrier formed between ZnS and CuS. Two emission peaks in luminance-wavelength spectra measured at applied voltage of 100 $V_{rms}$ were observed at 500nm as a primary peak and 460nm as a secondary peak, respectively.y.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.