• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.211-218
• /
• 2004

The objective of this study is to enhance the ultimate bearing capacity of piles embedded in marine clay by electrokinetic(EK). The focus of improvement is at interlace between soil and pile. A series laboratory test was performed in EK cell. In each of test, the pile in the centre as anode is surrounded by cathode and it was installed in the vicinity of pile with triangular layout. The pile was made by stainless and embedded with 30cm of depth. Afterward, the DC voltage was applied to electrode over period of time. It caused flowing water from anode to cathode, thus the soil in the center of box has higher bearing capacity value than in the side of box has. It is shown by increasing of un-drained shear strength(Cu) near the pile and also ultimate bearing capacity of pile increase after EK treatment. In the future work, the continuous of this study is finding the effective DC voltage and makes EK treatment more applicable in the field.

• Journal of Environmental Science International
• /
• v.14 no.7
• /
• pp.691-697
• /
• 2005

Waste sludge may be used to recovery wastewater contaminated with heavy metals. The waste sludge is an inexpensive readily available source of biomass for biosorption with metal-bearing wastewater. The biosorption of heavy metals such as Pb(II), Cu(II), Cr(II), and Cd(II) onto waste sludge was investigated in batch ex­periments and waste sludge loaded heavy metals was separated by dissolved air flotation. The biosorption equi­bria of heavy metals could be described by Langmuir and Freundich isotherms. The adsorption capacity for waste sludge was in the sequence of Pb(II)>Cr(II)>Cu(II)>Cd(II). The system attained equilibrium about 20 min. The Langmuir and Freundlich adsorption model effectively described the biosorption equilibrium of Cu(II) and Cr(II) ions on waste sludge. Maximum adsorption capacity of Cu(II) and Cr(II) were 196.08 and 158.73 mg/g, respectively. Solid-liquid separation efficiencies were kept above $95\%$ on waste sludge loaded heavy metals, and were decreased with pH increasing.

• Analytical Science and Technology
• /
• v.7 no.4
• /
• pp.517-526
• /
• 1994

Large insoluble phases and dispersoids in Al-Li-Cu-Mg-Mn-Zr alloys containing Mn were analyzed with EPMA(Electron Probe Microanalyzer) and SAEM(Scanning Auger Electron Microscope). Morphology, distribution and volume fraction of the large insoluble phase were also analyzed quantitatively by optical microscopy. Mechanical properties were tested at room temperature and at $200^{\circ}C$. With increasing Mn contents, the volume fraction of the large insoluble phases increased steeply, thus decreasing ductility. Mn was found to be very effective for obtaing uniformly distributed fine-grain structures. The alloy containing 0.44 wt% Mn showed the highest tensile strength among Mn-bearing alloys tested.

• Journal of Welding and Joining
• /
• v.26 no.5
• /
• pp.43-48
• /
• 2008

Characteristics of Sn-1.7%Bi-0.7%Cu-0.6%In (hereafter, SBIC) lead-free solder was investigated in this study. The results from SBIC were compared to other lead-free solders such as Sn-3.5%Ag-0.7%Cu (hereafter, SAC), Sn-0.7%Cu (hereafter, SC), and lead-bearing Sn-37%Pb (hereafter, SP) alloy. Tensile properties of bulk solder, wettability, spreading index, bridge and dross were evaluated. As experimental results, tensile strength and elongation of SBIC was 62.5MPa and 21.5%, respectively. The tensile strength was comparable to that of SP solder. The wetting time of SBIC was 1.2 sec at $250^{\circ}C$, and its wetting properties including wetting force were as good as the SAC alloy. However, wettability of the SC was not so good as the SBIC and SAC. The spreading index of SBIC at $250^{\circ}C$ was 71 %, and it was similar level to those of SAC and SC solders. Bridging was not found for all solders of SBIC, SAC and SC in the range from 240 to $260^{\circ}C$. In dross test at $250^{\circ}C$ for an hour, the amount of dross produced from SBIC was about 57% compared to that from SAC.

• Economic and Environmental Geology
• /
• v.24 no.3
• /
• pp.245-260
• /
• 1991

Surficial dispersion patterns of heavy metals and toxic elements (U, Mo, Cu, Zn, Fe, Mn, Co, Cr, V, Ni, Pb, and Cd) were investigated in the Dukpyungri, Goesan area covered with low grade uranium-bearing black shales. Maximum abundance of U in the black shale was 455ppm. Radioactivity was counted at a maximum of 7cps in black shales, and was less than 0.5cps in shales, slates, and oil shales of the control areas. Enrichment of Mo, V, Cu, Zn, Cd, and Pb in black shales is particularly characteristic compared with shales, slates, and oil shales of the control areas, whereas contents of Mn, Cr, Co, and Th in all rock samples tend to be almost similar. Residual top soils (0~15cm depth) over black shales show high contents of Mo, Cu, Zn, Ni, Cd, and V in comparison with the control areas. Contents of trace elements in subsoils (15~30cm depth) were higher about one and half times than those in topsoils. Average contents of Mo, Cu, Pb, Zn, Cd and V in garden soil and playground soil of an elementary school in Dukpyungri, Goesan area, were high about two to fifteen times compared with the control areas. Contents of trace elements in stream sediments were higher from two to eight times than those in residual soils. Sodium, AI, K, V, Cr, and Fe were more enriched in the roots of pine than in the twigs of pine. Contents of Li, AI, V, Ni, Cd, Fe, and Co were higher in the roots of azalea than in the twigs of azalea. Enrichment of P, Ca, and Mg was remarkable in the twigs of both pine and azalea. Biological absorption coefficients for essential elements (Zn, P, Mn, Ca and K)tend to be high, whereas those for the non-essential elements.(Ba, Ti, V, and Mo) and toxic elements(Cr, Co, Pb and Ni) be low. Less mobile elements (Pd, Cd, and Co) tend to show anomalies with higher contrast than more mobile elements(Mo, V, Zn, Cu and Ni) in the area covered with black shales.

• Tribology and Lubricants
• /
• v.18 no.1
• /
• pp.42-48
• /
• 2002

Experiments were conducted to determine the structural dynamic characteristics of bump foil bearing. The housing of the bearing on the journal was driven by two shakers which were used to simulate dynamic forces acting on the bump foil strips. Three different bump foils(Cu-coated bump, silicon bump, viscoelastic bump) are tested and the dynamic coefficients of three bump foils compared, based on the experimental measurements for a wide range of operating conditions. From the test results, the high damping coefficients of viscoelastic bump are achieved and the possibility of the super-bending-critical operation is suggested.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.282-289
• /
• 2001

Experiments were conducted to determine the structural dynamic characteristics of bump foil bearing. The housing of the bearing on the journal was driven by two shakers which were used to simulate dynamic forces acting on the bump foil strips. Three different bump foils(Cu-coated bump, silicon bump, viscoelastic bump) are tested and the dynamic coefficients of three bump foils compared, based on the experimental measurements for a wide range of operating conditions. From the test results, the high damping coefficients of viscoelastic bump are achieved and the possibility of the super-bending-critical operation is suggested.

• Corrosion Science and Technology
• /
• v.18 no.6
• /
• pp.300-311
• /
• 2019

The corrosion behaviors of twinning-induced plasticity (TWIP) steels with different alloying elements (Cu, Al, Si) in a neutral aqueous environment were investigated in terms of the characteristics of the corrosion products formed on the steel surface. The corrosion behavior was evaluated by measuring potentiodynamic polarization test and electrochemical impedance spectroscopy. For compositional analysis of the corrosion products formed on the steel surface, an electron probe x-ray micro analyzer was also utilized. This study showed that the addition of Cu to the steel contributed to the increase in corrosion resistance to a certain extent by the presence of metallic Cu in discontinuous form at the oxide/steel interface. Compared to the case of steel with Cu, the Al-bearing specimen exhibited much higher polarization resistance and lower corrosion current by the formation of a thin Al-enriched oxide layer. On the other hand, Si addition (3.0 wt%) to the steel led to an increase in grain size, which was twice as large as that of the other specimens, resulting in a deterioration of the corrosion resistance. This was closely associated with the localized corrosion attacks along the grain boundaries by the formation of a galvanic couple with a large cathode-small anode.

• Journal of Welding and Joining
• /
• v.13 no.4
• /
• pp.55-64
• /
• 1995

A study was made to examine the effects of postweld heat treatment(PWHT) on the toughness and microstructures in the weld heat affected zone(HAZ) of Cu-bearing HSLA-100 steel. The Gleeble thermal/mechanical simulator was used to simulate the weld HAZ. The details between toughness and PWHT of HAZ were studied by impact test, optical microscopy(O.M.), scanning electron microscopy (SEM), transmission electron microscopy(TEM) and differential scanning calorimetry(DSC). The decrease of HAZ toughness in single thermal cycle comparing to base plate is ascribed to the coarsed-grain formed by heating to 1350.deg.C. The increase of HAZ toughness in double thermal cycle comparine to single thermal cycle is due to the fine ferrite(.alpha.) grain transformed from austenite(.gamma.)formed by heating to .alpha./.gamma. two phase region. Cu precipitated during aging for increasing the strength of base metal is dissolved during single thermal cycle to 1350.deg.C and is precipitated little on cooling and heating during subsequent weld thermal cycle. It precipitates by introducing PWHT. Thus, the decrease of toughness in triple thermal cycle of $T_{p1}$ = 1350.deg.C, $T_{p2}$ = 800.deg.C and $T_{p3}$ = 500.deg.C does not occur owing to the precipitation of Cu. The behaviors of Cu=precipitates in HAZ is similar to that in base plate. PWHT at 550.deg.C shows highest hardness and lowest toughness, whereas PWHT at 650.deg.C shows reasonable toughness, which improves the toughness of as-welded state.state.

• Economic and Environmental Geology
• /
• v.31 no.6
• /
• pp.463-472
• /
• 1998

The survey was carried out in order to delineate the occurrence of ore deposits and the mineralized characteristics in the Estancia de la Virgen area through the 1:2,000 scaled geological mapping and topographic measuring surveys. Gold-silver mineralization is in the fault block developed between the San Agustin Fault and Cabanas Fault. It is associated with ore bearing quartz veins controlled by the fault structure. The contents of Au and Ag range from traces up to 72 g/t and 180 g/t respectively. According to traversing the outcrops, the quartz veins are traced by 0.5 Km trended to north and south. In those extended part, they continue for 1,000 m intermittently. Gold-silver mineralization could be divided into three stages. In the first stage, pyrite, galena, sphalerite, and chalcopyrite were formed with the primary silver and gold associated with galena and copper sulfides respectively. In the second stage, Cu-Bi-Au-Ag bearing sulfides such as chalcocite, covellite, and linarite are formed and usually deposited on the cataclastic fractures of galena and/or chalcopyrite. In the third stage, both the carbonation of galena and sphalerite and the sulphatization of galena, took place in the surface environment. And then primary silver was carried away off and was deposited on galena and/or copper sulfides during oxidation near the water table. Low partitionings of Fe in sphalerite assist that the minerals were formed at the relatively low temperature, which is coincided with previously reported homogenization temperature of fluid inclusions.