• Transactions of Materials Processing
• /
• v.26 no.6
• /
• pp.356-364
• /
• 2017

In this study, submerged arc cladded Fe-Cr-Ni-Mo-CuWNbV-C stainless steels containing various Cr contents between 11.2 wt.% and 16.7 wt.% were prepared with fixed C content at about 0.14 wt.%. Using these alloys, changes in microstructure, tensile property, and thermal fatigue property were investigated. Phase fraction of delta-ferrite was increased gradually with increasing Cr content. However, tensile strength, hardness, and thermal fatigue resistance appeared to be decreased. When the microstructure of delta-ferrite was observed, it was revealed that the mesh structure retained up to about 15% Cr content. Although thermal fatigue resistance was almost the same for Cr contents between 11.0 and 14.5 wt.%, it was significantly decreased at higher Cr contents. This was evident from mean value of crack lengths of 10 largest ones. Evaluation of thermal fatigue resistance on alloys with various Cr contents revealed the following important results. First, the reproducibility of ranking test was excellent regardless of the number of cycles. Second, thermal fatigue resistance was increased in proportion to true tensile fracture strength values of overlay materials. Finally, the number of thermal fatigue cracks per unit length was increased with increasing true tensile fracture strength.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.781-786
• /
• 2015

It is necessary for ferrite sheets to be fabricated with high packing density for excellent electrical properties and high strength. In this study, the relationship between the warpage and the packing density of ferrite green sheet, was investigated with amount variation of organic additives. With 0.4 wt% of dispersant, the packing density was about 48% and warpage appeared 0.5~1.3 mm high. With 1.4 wt% of dispersant, the packing density increased up to 57% and warpage appeared 0.8~2.1 mm high. With high packing density, warpage appeared along the edges of specimen, while with low packing density, deformation appeared over whole specimen inhomogeneously. It is thought that inhomogeneous deformation after sintering came from the inhomogeneity in green sheet prepared with badly dispersed slurry. With good homogeneity in green sheet from well-dispersed slurry, isotropic shrinkage is thought to have occurred along the distance from center to edges of specimen during sintering.

• Korean Journal of Metals and Materials
• /
• v.48 no.4
• /
• pp.289-296
• /
• 2010

The effects of heat input and different microstructureswere investigated on the tensile-shear properties of an arc-brazed joint of theferritic stainless steel 429EM using a Cu-Si insert alloy. The brazing speed was fixed at 800 mm/min whilethe brazing current varied from 80 to 120A. For abrazing current lower than 100A, fracturing occurred at the joint root in the direction perpendicular to the tensile load. As the brazing current increased to 120A, fracturing occurred at the base metal or the joint root. The joint and the base metal had very similar yield and tensile load values. However, the amount of elongation was decreased considerably compared to when the base metal was used. The fracturing began at the triple point of the root part and was classified into three types. The difference in the tensile-shear properties was closely related to the three fracture types.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.4
• /
• pp.356-364
• /
• 2007

The partial reduction and water splitting properties of metal substituted ferrite mediums for two-step thermochemical hydrogen production, were carried out by TPR/O(Temperature programmed reduction/oxidation) method at a temperature of below 1173 K and under atmospheric pressure. $ZrO_2$ was added to the ferrite as a binder to prevent the sintering. As the results, the reactivity of the metal species added to the ferrite mediums decreased in the order of Cu>Co>Ni>Mn, on the basis of water-splitting temperature. It was also found that the produced hydrogen amounts in the water-splitting step on partial reduced mediums were corresponding to the consumed hydrogen amounts in the previously partial reduction step.

• Journal of Powder Materials
• /
• v.15 no.4
• /
• pp.292-296
• /
• 2008

The electromagnetic (EM) wave absorption properties of the $Fe_{73}Si_{16}B_7Nb_3Cu_1$ nanocrystalline powder mixed with 5 to 20 vol% of Ni-Zn ferrites has been investigated in a frequency range from 100MHz to 10GHz. Amorphous ribbons prepared by a planar flow casting process were pulverized and milled after annealing at 425 for 1 hour. The powder was mixed with a ferrite powder at various volume ratios to tape-cast into a 1.0mm thick sheet. Results showed that the EM wave absorption sheet with Ni-Zn ferrite powder reduced complex permittivity due to low dielectric constant of ferrite compared with nanocrystalline powder, while that with 5 vol% of ferrite showed relatively higher imaginary part of permeability. The sheet mixed with 5 vol% ferrite powder showed the best electromagnetic wave absorption properties at high frequency ranges, which resulted from the increased imaginary part of permeability due to reduced eddy current.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.201-201
• /
• 2006

영구자석은 크게 Hard ferrite와 희토류계 자석, 그리고 Alnico 주조자석으로 구별되어진다. 그동안 Hard ferrite는 산업적으로 전자기 응용제품 또는 각종 구동 모터에 응용되어 왔지만, 최근 Nd계 희토류 자것이 고성능 모터의 소재로 급격히 대체되고 있다. 하지만, 희토류계 원료에 비해 동일 중량 대비 40~60배 가량 저렴한 Hard ferrite의 사용은 현재까지도 꾸준히 유지되고 있으며, 최근 자동차 고성능 모터용 Sr ferrite의 개발이 연구 중이다.[2] 본 연구에서는 제일원리 전산모사를 통하여 HCP 구조의 기본 Unit Cell 64개 원자를 가진 Sr-ferrite의 격자상수를 계산하여 기존 연구결과와 비교하였으며, 자화에너지와 자기모멘트를 계산하였다. 또한 향후 각종 첨가물의 영향에 대한 연구를 위해 기본 구조 및 치환 구조에 대해 고찰하였다. 그 결과 가장 안정한 에너지를 갖는 격자상수는 a=5.88, b=23.03으로 계산되어 Kimura et al의 측정 결과와 유사한 결과를 얻을 수 있었으며, $E_F$가 3.9171, $M_B$는 46.6481로 계산되었다. 항후 Sr-ferrite의 구조에서 Fe atom의 일부를 동일주기 원소인 Cr, Mn, Co, Ni, Cu로 치환하여 자기적 특성을 계산하여 본 연구결과와 비교하고자 한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.109-114
• /
• 2000

In this paper, we studied the relation between heat-treatment temperature of ferrite and electromagnetic wave absorbing properties of ferrite-rubber composite. The heat-treatment temperatures of ferrite are 1200 and 1300 $^{\circ}C$, 2 hr. As s result, it has been shown that the optimum heat-treatment temperature of ferrite for electromagnetic wave absorber are related to the chemical composition. And, we can control electromagnetic wave absorbing properties of ferrite-rubber composite by the control of heat-treatment temperature of ferrite.

• Korean Journal of Materials Research
• /
• v.12 no.8
• /
• pp.600-607
• /
• 2002

The Ni-Zn synthetic ferrite were acquired from thermally decomposing the metal nitrates Fe(NO$_3$)$_3$.$9H_2$O, Zn($NO_3$)$_2$.$6H_2$O, Ni($NO_3$)$_2$. $6H_2$O, and Cu($NO_3$)$_2$. $3H_2$O at $150^{\circ}C$ for 24 hours and was calcined at $500^{\circ}C$. Each of those was pulverized for 3, 6, 9, and 12 hours in a steel ball mill and was sintered between $700^{\circ}C$ and $1,000^{\circ}C$ for 1 hour, and then their microstructures and electromagnetic properties were examined. We could make the initial specimens chemically bonded in liquid at the temperature as low as $150^{\circ}C$, by using the melting points less than $200^{\circ}C$ of the metal nitrates instead of the mechanical ball milling, then narrowed a distance between the particles into a molecular level, and thus lowed sintering temperature by at least $200^{\circ}C$ to$ 300^{\circ}C$. Their initial permeability was 50 to 400 and their saturation magnetic induction density and coercive force 2,400 G and 0.3 Oe to 0.5 Oe each, which were similar to those of Ni- Zn ferrite synthesized in the conventional process. In the graph of initial permeability vs frequencies, we could observe a $180^{\circ}C$rotation of the magnetic domain, which appears in a broad band of microwave near the resonance frequency.

• Korean Journal of Metals and Materials
• /
• v.46 no.9
• /
• pp.593-603
• /
• 2008

In this study, effects of alloying elements on the sticking occurring during hot rolling of five kinds of ferritic STS430J1L stainless steels were investigated by analyzing high-temperature hardness and oxidation behavior of the rolled steels. Hot-rolling simulation tests were conducted by a high-temperature wear tester which could simulate actual hot rolling. The simulation test results revealed that the sticking process proceeded with three stages, i.e., nucleation, growth, and saturation. Since the hardness continuously decreased as the test temperature increased, whereas the formation of Fe-Cr oxides in the rolled steel surface region increased, the sticking of five stainless steels was evaluated by considering both the high-temperature hardness and oxidation effects. The addition of Zr, Cu, or Si had a beneficial effect on the sticking resistance, while the Ni addition did not show any difference in the sticking. Particularly in the case of the Si addition, Si oxides formed first in the initial stage of high-temperature oxidation, worked as initiation sites for Fe-Cr oxides, accelerated the formation of Fe-Cr oxides, and thus raised the sticking resistance by about 10 times in comparison with the steel without Si content.