• 마이크로전자및패키징학회지
• /
• 제20권4호
• /
• pp.47-52
• /
• 2013

Gold wire has long been used as a proven method of connecting a silicon die to a substrate in wide variety of package types, delivering high yield and productivity. However, with the high price of gold, the semiconductor packaging industry has been implementing an alternate wire material. These materials may include silver (Ag) or copper (Cu) alloys as an alternative to save material cost and maintain electrical performance. This paper will analyze and compare the electrical characteristics of several wire types. For the study, typical 0.6 mil, 0.8 mil and 1.0 mil diameter wires were selected from various alloy types (2N gold, Palladium (Pd) coated/doped copper, 88% and 96% silver) as well as respective pure metallic wires for comparison. Each wire model was validated by comparing it to electromagnetic simulation results and measurement data. Measurements from the implemented test boards were done using a vector network analyzer (VNA) and probe station setup. The test board layout consisted of three parts: 1. Analysis of the diameter, length and material characteristic of each wire; 2. Comparison between a microstrip line and the wire to microstrip line transition; and 3. Analysis of the wire's cross-talk. These areas will be discussed in detail along with all the extracted results from each type the wire.

• Applied Microscopy
• /
• 제45권2호
• /
• pp.37-43
• /
• 2015

In present work, work-hardening behavior of TiCu-based bulk metallic glass composite with B2 particles has been studied by systemic structural and mechanical investigations. After yield, pronounced work-hardening of the alloy was clearly exhibited, which was mainly related to the martensitic transformation as well as the deformation twinning in B2 particles during deformation. At the early plastic deformation stage (work-hardening stage), the stress-induced martensitic transformation from B2 phase to B19' phase and deformation-induced twinning of B19' phase was preferentially occurred in the around interface areas between B2 phase and amorphous matrix by stress concentration. The higher hardness value was observed in vicinity of interface within the B2 particles which are probably connected with martensitic transformation and deformation twinning. This reveals that the work-hardening phenomenon of this bulk metallic glass composite is a result of the hardening of B2 particles embedded in amorphous matrix.

• 한국주조공학회지
• /
• 제33권3호
• /
• pp.113-121
• /
• 2013

The effects of Zn and Mg amounts on the solidification characteristics, microstructure, thermal conductivity and tensile strength of Al-Zn-Mg-Fe alloys were investigated for the development of high thermal conductivity aluminium alloys for die casting. Zn and Mg amounts in Al-Zn-Mg-Fe alloys had a little effect on the liquidus / solidus temperature, the latent heat for solidification and the fluidity of Al-Zn-Mg-Fe alloys. Thermo-physical modelling of Al-Zn-Mg-Fe alloys by JMatPro program showed $MgZn_2$, AlCuMgZn and Al3Fe phases on microstructure of their alloys. Increase of Zn and Mg amounts in Al-Zn-Mg-Fe alloys resulted in gradual reduction of the thermal conductivity of their alloys. Increase of Mg amounts in Al-2%Zn-Mg-Fe alloys had little effect on the tensile strength of their alloys, but increase of Mg amounts in Al-4%Zn-Mg-Fe alloys resulted in steep increase of the tensile strength of their alloys.

• 한국정보통신학회논문지
• /
• 제9권3호
• /
• pp.602-608
• /
• 2005

단상 단방향 형태의 표면 탄성파 필터 제작하기 위하여 Langasite 기판위에 빗살무늬 변환기를 형성시켜 모의실험을 수행하였으며, 전극재료로는 Al-Cu를 사용하였다. 모의실험을 바탕으로 입력단에는 IDT를 직렬형태로 연결시킨 block 형태로 하중을 가하는 전극 방법을 쓰고 출력단은 withdrawal 형태로 하중을 가하는 방법을 써서 제작하였다. 이를 바탕으로 단상 단방향 형태의 표면 탄성파 필터 적절한 임피던스 정합 조건도 얻고자 하였다. Langasite 기판 위에 형성시킨 입출력 빗살무늬 변환기 전극 수는 50쌍, 두께는 $5000{\AA}$으로 하였으며, 반사기 폭은 $3.6{\mu}m$이며, 전극 폭은 $2.4{\mu}m$이고, 전극과 반사기 사이의 간격은 $2.0{\mu}m$으로 하였다. 제작한 필터의 임피던스 정합 후 주파수 특성에서 중심 주파수는 190MHz, 대역폭은 7.7MHz 정도로 측정되었으며, 리플 특성은 0.4dB 이하이고, 정재파 비는 1.5정도로 측정되었다.

• 한국주조공학회지
• /
• 제36권6호
• /
• pp.202-207
• /
• 2016

The effects of Fe and Si additions on the microstructures and mechanical properties of aluminum bronze have been investigated. In a bar-type specimen cast in a die mold, the addition of Fe promoted the dendritic solidification of the ${\alpha}$ phase. The hardness values increased slightly in the Fe-added specimen with heat treatment, while these values was increased significantly in the specimens with Si or with combined additions of Fe and Si. When a centrifugal casting bush with combined addition of Fe and Si was heat treated, the FeSi compound within the matrix was finely dispersed, and was observed to be the origin of cup-cone type conical dimple failure in the tensile fracture surface. The mechanical properties of the heat treated centrifugal casting bushes, whose nominal alloy compositions were (Cu-7.0Al-0.8Fe-3.0Si)wt%, exhibited tensile strength of $703-781N/mm^2$, elongation of 6.6-11.7% and hardness of Hv 222.6-249.2. These high values of strength and elongation were attributed to the strengthening of the matrix due to the combined addition of Fe and Si, and to precipitation of fine the FeSi compound.

• 보존과학회지
• /
• 제29권3호
• /
• pp.231-241
• /
• 2013

성남 판교에서 출토된 청동보살상 2점의 제작기법을 알아보기 위해 CT촬영, ICP-AES, 금속현미경, SEM-EDS를 이용하여 분석하였다. 또한 원료의 산지는 TIMS(납동위원소비)를 이용하여 알아보았다. CT촬영결과 2점의 청동보살상 모두 중공식 밀납법을 사용하여 제작되었으며, 내부의 철심을 확인할 수 있었다. 성분 및 미세조직 관찰 결과 두 점 모두 Cu-Sn-Pb의 삼원계 합금으로 열처리를 비롯한 인공적인 가공 없이 주조로 제작되었다. 납동위원소비 분석 결과 2점의 청동보살상은 한반도 남부 경기지괴의 방연석을 사용하여 제작되었을 가능성이 크다.

• 대한기계학회논문집B
• /
• 제29권11호
• /
• pp.1229-1238
• /
• 2005

The objective of the present study was to investigate the efficacy of physical water treatment (PWT) technologies using different catalytic materials and an electronic anti-fouling device in the mitigation of mineral fouling in a once-through flow system with mini-channel heat exchanger. Effects of flow velocity and water hardness on the effectiveness of PWT technologies were experimentally studied. The artificial water hardness varied from 5.0 to 10 mo1/m$^{3}$ as CaCO$_{3}$. For 10 mo1/m$^{3}$ solution, fouling resistance reduced by 13-40$\%$ depending on flow velocity and types of PWT devices. On the other hand, fouling resistance reduced by 21-29$\%$ depending on the PWT devices for 5 mo11m3 solutions. The PWT device using alloy of Cu and Zn as catalyst (CM2) was slightly more effective than the others. SEM photographs of scale produced from the 10 mol/m$^{3}$ solution at 1.0 m/s indicated that calcium carbonate scales without PWT devices were needle-shaped aragonite, which is sticky, dense and difficult to remove. Scales with the PWT devices showed a cluster of spherical or elliptic shape crystals. Both the heat transfer test results and SEM photographs strongly support the efficacy of PWT technologies using catalytic materials and an electronic anti-fouling device in the mitigation of mineral fouling.

• 열처리공학회지
• /
• 제25권1호
• /
• pp.22-26
• /
• 2012

An influence of the addition of copper (0.5, 1.0 and 1.5 mass% Cu) on the microstructure and mechanical properties of high purity iron (99.998 mass%) was characterized. The microstructure and microhardness of high-purity iron based samples, which were rolled at room temperature and subsequently annealed, were investigated in this work. The microstructure of the samples has been observed by electron back scattering diffraction (EBSD) and the mechanical properties have been studied by using micro-Vickers hardness test. The results of microstructural observation showed that deformation band was formed in high purity iron by rolling at room temperature, and it was recovered by annealing up to about 900 K. The microhardness results showed that the softening of high-purity iron occurred by annealing up to about 900 K, while the hardness of iron added with about 0.5-1.5 mass% copper was kept over 100 Hv and at the early time of annealing reached a maximum. The hardness of iron added with a small amount of copper may be attributed to precipitation hardening as well as solution hardening. The orientation of crystal in recrystallized grain was almost same as that of deformed grain.

• 자원환경지질
• /
• 제24권2호
• /
• pp.151-165
• /
• 1991

The Au-Ag deposits of the Euiseong area occurred in quartz veins which filled fissures in Cretaceous sedimentary and volcanic rocks. These ore veins can be classified in two types of deposits based on metallic mineral assemblages as follow: a pyrite type gold-silver deposit (Hoedong mine), characterized by Cu sulfides with Au-Ag alloy, and a Sb-rich silver deposit (Keumdongdo mine), characterized by base metal with Ag-bearing sulfosalts. Mineralogic and fluid inclusion evidences suggest that the ore minerals of these deposits was deposited from initial high temperatures (near $350^{\circ}C$) to later lower temperatures ($200^{\circ}C$) with moderate salinity fluids ranging from 5.8 to 3.8 eq. wt. % NaCl. The gold-silver mineralization of the Hoedong mine occurred at temperatures between 300 and $200^{\circ}C$ from fluids with log $f_{s_2}$ of -10 ~ -16 atm. The antimony - silver mineralization of the Keumdongdo mine were deposited at the higher temperatures (350 to $250^{\circ}C$) and $f_{S_2}$ (-10 ~ -13 atm) than gold mineralization of the Hoedong mine. The calculated log f02 of fluids at $250^{\circ}C$ in two deposits are -32 to -34 atm and -36.5 to -38.5 atm, respectively. Boiling evidences indicate that the ore mineralization of the Hoedong mine occurred at more shallow depth (0.5km) than that (1km) of the Keumdongdo mine. The above differences of depositional environments between two deposits caused the compositional changes of ore minerals such as electrum and sphalerite.

• 열처리공학회지
• /
• 제14권4호
• /
• pp.220-227
• /
• 2001

The static creep behaviors of dispersion strengthened copper GlidCop were investigated over the temperature range of $650{\sim}690^{\circ}C$ (0.7Tm) and the stress range of 40~55 MPa (4.077~5.61 $kg/mm^2$). The stress exponents for the static creep deformation of this alloy was 8.42, 9.01, 9.25, 9.66 at the temperature of 690, 677, 663, and $650^{\circ}C$, respectively. The stress exponent, (n) increased with decreasing the temperature and became dose to 10. The apparent activation energy for the static creep deformation, (Q) was 374.79, 368.06, 361.83, and 357.61 kg/mole for the stress of 40, 45, 50, and 55 MPa, respectively. The activation energy (Q) decreased with increasing the stress and was higher than that of self diffusion of Cu in the dispersion strengthened copper. In results, it can be concluded that the static creep deformation for dispersion strengthened copper was controlled by the dislocation climb over the ranges of the experimental conditions. Larson-Miller parameter (P) for the crept specimens for dispersion strengthened copper under the static creep conditions was obtained as P=(T+460)(logtr+23). The failure plane observed for SEM slightly showed up transgranular at that experimental range, however, universally it was dominated by characteristic of the intergranular fracture.