• 한국수소및신에너지학회논문집
• /
• 제34권6호
• /
• pp.615-622
• /
• 2023

In this study, the theoretical analysis focused on the quantity of liquid hydrogen required for cooling down to 20 K, as well as the generation of boil-off gas (BOG) from the cooling process of the cryogenic components. The study involved calculating the amount of liquid hydrogen needed to achieve the desired temperature for the cryogenic components and subsequently determining the resulting BOG production at various reference temperatures. It was shown that it was important to efficiently lower the temperature of cryogenic parts through preliminary cooling. As a result, the reference temperature and pressure had an influence on the BOG generation on the cooling of cryogenic components using liquid hydrogen.

• 한국수소및신에너지학회논문집
• /
• 제26권5호
• /
• pp.402-408
• /
• 2015

In D-T fusion reaction, $D_2$ (duterium) and $T_2$(tritium) are used as fuel gas. The exhaust gas of nuclear fusion includes hydrogen isotopes $Q_2$ (Q means H, D or T), tritiated components ($CQ_4$ and $Q_2O$), CO, $CO_2$, etc. All of hydrogen isotopes should be recovered before released to the atmosphere. This study focused on the recovery of hydrogen isotopes from $CQ_4$ and $Q_2O$. Two kinds of experiments were conducted to investigate the catalytic reaction characteristics of SMR (Steam Methane Reforming) and WGS (Water Gas Shift) reactions using Pt catalyst. First test was performed to convert $CH_4$ into $H_2$ using 6% $CH_4$, 6% CO/Ar feed gas. In the other test, 100% CO gas was used to convert $H_2O$ into $H_2$ at various reaction conditions (reaction temperature, S/C ratio, GHSV). As a result of the first test, $CH_4$ and CO conversion were 41.6%, 57.8% respectively at $600^{\circ}C$, S/C ratio 3, GHSV $2000hr^{-1}$. And CO conversion was 72% at $400^{\circ}C$, S/C ratio 0.95, GHSV $333hr^{-1}$ in the second test.

• Journal of Mechanical Science and Technology
• /
• 제20권7호
• /
• pp.972-980
• /
• 2006

In general, to send out natural gas via a pipeline network across the nation in LNG terminal, high-pressure cryogenic pump supply highly compressed LNG to high-pressure vaporization facilities. The Number of cryogenic pumps determined the send-out amount in LNG receiving terminal. So it is main equipment at LNG production process and should be maintained on best conditions. In this paper, to find out the cause of high vibration at cryogenic pumps-motor system in LNG terminal, vibration spectrum analysis and motor current signature analysis have been performed together. Through the analysis, motor rotor bar problems are estimated by the vibration analysis and confirmed by the current analysis. So, it is demonstrated through the case study in this paper, how performing vibration analysis and current signature analysis together can reliable diagnosis rotor bar problems in pump-motor system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.666-671
• /
• 2007

To acquire the safety along with durability of mechanical machinery products, we should consider the structural mechanics such as stress, deformation and dynamic vibration characteristics and identify those important aspects in the stage of preliminary design engineering. This cryogenic ball valve is used to transfer the liquified natural gas which temperature is $-196^{\circ}C$, supplied pressure is $168kg/cm^2$. For the cryogenic ball valve, the assurance of structural integrity and operability are essential to meet not only normal, abnormal loading conditions but also functionality during a seismic event. In this thesis, analytical approach and results using finite element analysis and computational method are herein presented to evaluate the aspects of structural integrity along with operability of cryogenic ball valve. In this study, we designed the high pressure cryogenic ball valve that accomplishes zero leakage by elastic seal at normal temperature and metal seal at high temperature.

• 한국초전도ㆍ저온공학회논문지
• /
• 제17권3호
• /
• pp.41-46
• /
• 2015

Recently, the development of the HTS power cable is actively promoted. As the length of HTS power cable increases, there have been many efforts to develop large capacity cryocooler. Among the various cryocooler, the Brayton refrigerator is the most competitive for HTS power cable. The Brayton refrigerator is composed of recuperative heat exchangers, a compressor, and a cryogenic turbo expander. In these components, the cryogenic turbo expander is a part to decrease the temperature and it is the most significant component that is closely related with overall system efficiency. It rotates with high speed using a high-pressure helium or neon gas at cryogenic temperature. This paper describes the design of a 10 kW class Brayton refrigeration cycle and the cryogenic turbo expander. Flow and structural analysis are performed for the rotating impeller and nozzle to verify the efficiency and the design performance.

• 한국초전도ㆍ저온공학회논문지
• /
• 제22권1호
• /
• pp.24-28
• /
• 2020

Heat leakage is an important parameter to reflect heat insulated performance of cryogenic vessel. According to the current standard requirements, it needs to measure the daily evaporation rate to indicate heat leakage. The test needs-over 24h after cryogenic vessel in heat equilibrium as standard required, therefore test efficiency is poor and new efficient method is required to cut test time. First of all, the volume of instantaneous evaporated gas and heat leakage are calculated by the current standard corresponding to the maximum allowable daily evaporation rate of cryogenic vessel. Depending on the relationship between real daily evaporation rate and maximum allowable daily evaporation rate of cryogenic vessel, we designed a new test method based on the pressure changes over time in cryogenic vessel to determine whether its heat insulated performance meets requirements or not. Secondly, the heat transfer process was analyzed in measurement of cryogenic vessel, and the heat transfer equations of whole system were established. Finally, the test was completed in four hours; meanwhile the heat leakage and daily evaporation rate of cryogenic vessel are calculated basing on test data.

• 한국초전도ㆍ저온공학회논문지
• /
• 제25권4호
• /
• pp.65-69
• /
• 2023

Hydrogen is an eco-friendly energy source and is being actively researched in various fields around the world, including mobility and aerospace. In order to effectively utilize hydrogen energy, it should be used in a liquid state with high energy storage density, but when hydrogen is stored in a liquid state, BOG (boil-off gas) is generated due to the temperature difference with the atmosphere. This should be re-condensed when considering storage efficiency and economy. In particular, large-capacity liquid hydrogen storage tank is required a gaseous helium circulation cooling system that cools by circulating cryogenic refrigerant due to the increase in heat intrusion from external air as the heat transfer area increases and the wide distribution of the gas layer inside the tank. In order to effectively apply the system, thermo-hydraulic analysis through process analysis is required. In this study, the condenser design and system characteristics of a gaseous helium circulation cooling system for BOG recondensation of a liquefied hydrogen storage tank were compared.

• 플랜트 저널
• /
• 제16권3호
• /
• pp.42-46
• /
• 2020

FLNG 혹은 FSRU와 같이 대량의 LNG를 처리하는 공정에서의 LNG 누출 사고 시, 강재의 급격한 온도변화는 구조물의 취성파괴를 야기시킬 가능성이 있다. 본 논문에서는 극저온 유출 실험을 통해 극저온 유체가 강판에 형성되는 원리 및 과정을 알아보고, 노즐로부터의 거리 및 노출시간에 따른 강판의 온도변화의 상관관계를 분석하고자 한다. 극저온 유체는 LN2(비점 -192℃) 및 LNG(비점 -162℃) 두 가지 종류를 사용하였으며, 유출량은 LN2의 경우 1.6L/min 및 LNG 1.5L/min로 강판의 상부에서 분사하였다. 강재는 DH계열 이용하였으며, 총 10 지점에서 온도를 측정하였다. 실험 결과 극저온 유출 초기 강재표면에서 Leidenfrost 효과가 관찰 되었으며, 극저온 유체가 흐르는 경로 및 유체의 증발열에 차이에 따라 강재의 온도분포가 다르게 나타나는 것을 발견하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제22권3호
• /
• pp.20-24
• /
• 2020

The purpose of this analytic study is to design and examine an efficient hydrogen liquefaction cycle by using a pre-cooler. The liquefaction cycle is primarily comprised of a pre-cooler and a refrigerator. The fed hydrogen gas is cooled down from ambient temperature (300 K) to the pre-cooling coolant temperature (either 77 K or 120 K approximately) through the pre-cooler. There are two pre-cooling methods: a single pre-coolant pre-cooler and a cascade pre-cooler which uses two levels of pre-coolants. After heat exchanging with the pre-cooler, the hydrogen gas is further cooled and finally liquefied through the refrigerator. The working fluids of the potential pre-cooling cycle are selected as liquid nitrogen and liquefied natural gas. A commercial software Aspen HYSYS is utilized to perform the numerical simulation of the proposed liquefaction cycle. Efficiency is compared with respect to the various conditions of the heat exchanging part of the pre-cooler. The analysis results show that the cascade method is more efficient, and the heat exchanging part of the pre-coolers should have specific UA ratios to maximize both spatial and energy efficiencies. This paper presents the quantitative performance of the pre-cooler in the hydrogen liquefaction cycle in detail, which shall be useful for designing an energy-efficient liquefaction system.

• 한국진공학회지
• /
• 제8권4A호
• /
• pp.476-481
• /
• 1999

Characteristics of platinum dry etching were investigated in a cryogenic magnetized inductively coupled plasma (MICP). The problem with platinum etching is the redeposition of sputtered platinum on the sidewall. Because of the redeposits on the sidewall, the etching of patterned platinum structure produces feature sizes that exceed the original dimension of the PR size and the etch profile has needle-like shape [1]. The main object of this study was to investigate a new process technology for fence-free Pt etching As bias voltage increased, the height of fence was reduced. In cryogenic etching, the height of fence was reduced to 20% at-$190^{\circ}C$ compared with that of room temperature, however the etch profile was not still fence-free. In Ar/$SF_6$ Plasma, fence-free Pt etching was possible. As the ratio of $SF_6$ gas flow is more than 14% of total gas flow, the etch profile had no fence. Chemical reaction seemed to take place in the etch process.