• Proceedings of the Korean Information Science Society Conference
• /
• 2007.10d
• /
• pp.240-243
• /
• 2007

Geographic routing has been considered as an efficient simple, and scalable routing protocol for wireless sensor networks since it exploits pure location information instead of global topology information to route data packets. Geographic routing requires the sources nodes to be aware of the location of the sinks. In this paper, we propose a scheme named Sink Location Service for geographic routing in wireless Sensor Networks, in which the source nodes can get and update the location of sinks with low overhead. In this scheme, a source and a sink send data announcement and query messages along two paths respectively by geographic routing. The node located on the crossing point of the two paths informs the source about the location of the sink. Then the source can send data packet to the sink by geographic routing. How to guarantee that these two paths have at least one crossing point in any irregular profile of sensor network is the challenge of this paper.

• Clean Technology
• /
• v.19 no.4
• /
• pp.469-475
• /
• 2013

In this research, the stabilization characteristics of upgraded coal using palm oil residues were investigated. The Eco coal, which is the Indonesian low-rank coal, was used as a raw material. The low-rank coal was mixed with palm fatty acid distillate (PFAD), and then dried in a nitrogen atmosphere at $107^{\circ}C$. The trend of spontaneous combustion of upgraded coal was studied by measuring of crossing-point temperature (CPT), low temperature oxidation and moisture readsorption. The results of the CPT measuring and low temperature oxidation showed that the propensity of spontaneous combustion of the upgraded coal was improved compared to the dried coal. The moisture readsorption characteristics of the upgraded coal was also improved. The upgraded coal was stabilized through the surface coating with PFAD, and stability of upgraded coal was proportional to the content of PFAD.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.1A
• /
• pp.104-112
• /
• 2005

Some design techniques for high speed and low power pipelined 8-bit ADC are described. To perform high-speed operation with relatively low power consumption, open loop architecture is adopted, while closed loop architecture (with MDAC) is used in conventional pipeline ADC. A distributed track and hold amplifier and a cascading structure are also adopted to increase the sampling rate. To reduce the power consumption and the die area, the number of amplifiers in each stage are optimized and reduced with proposed zero-crossing point generation method. At 500-MHz sampling rate, simulation results show that the power consumption is 210mW including digital logic with 1.8V power supply. And the targeted ADC achieves ENOB of about 8-bit with input frequency up to 200-MHz and input range of 1.2Vpp (Differential). The ADC is designed using a $0.18{\mu}m$ 6-Metal 1-Poly CMOS process and occupies an area of $900{\mu}m{\times}500{\mu}m$

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.10
• /
• pp.768-776
• /
• 2006

Given an unstructured point set, we use an MLS (melting least-squares) approximation to estimate the local curvatures and their derivatives at a point by means of an approximation surface Then, we compute neighbor information using a Delaunay tessellation. feature points can then be detected as zero-crossings, and connected using curvature directions. Also this approach has a fast computation time than previous methods, which based on triangle meshes. We demonstrate our method on several large point-sampled models, rendered by point-splatting, on which the feature lines are rendered with line width determined from curvatures.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.3
• /
• pp.173-179
• /
• 1999

In reverse engineering, when a shape containing multi-patched surfaces is digitized, the boundaries of these surfaces should be detected. The objective of this paper is to introduce a computationally efficient segmentation technique for extracting edges, ad partitioning the 3D measuring point data based on the location of the boundaries. The procedure begins with the identification of the edge points. An automatic edge-based approach is developed on the basis of local geometry. A parametric quadric surface approximation method is used to estimate the local surface curvature properties. the least-square approximation scheme minimizes the sum of the squares of the actual euclidean distance between the neighborhood data points and the parametric quadric surface. The surface curvatures and the principal directions are computed from the locally approximated surfaces. Edge points are identified as the curvature extremes, and zero-crossing, which are found from the estimated surface curvatures. After edge points are identified, edge-neighborhood chain-coding algorithm is used for forming boundary curves. The original point set is then broke down into subsets, which meet along the boundaries, by scan line algorithm. All point data are applied to each boundary loops to partition the points to different regions. Experimental results are presented to verify the developed method.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.3
• /
• pp.111-115
• /
• 2012

Generally, brushless DC motor(BLDCM) driving system uses hall sensors or encoders as the mechanical position or speed sensor. It is necessary to achieve the informations of rotor position for driving trapezoidal type brushless DC motor without any position sensor. In this paper, the commutation signals are obtained without the motor neutral voltage, multistage analog filters, A/D converters, or the complex digital phase shift circuits which are indispensable in the conventional sensorless control algorithms. In the proposed method, in stead of detecting the zero crossing point of the nonexcited motor back electromagnetic force for the average motor terminal to neutral voltage, the commutation signal are extracted directly from the specific average line to line voltage with low-pass filter, adder and comparators circuit. In contrast to conventional methods, the neutral voltage is not need; therefore, the commutation signals are insensitive to the common mode noise. Moreover, the complex phase shift circuit can be eliminated. The effectiveness of the proposed method is verified through simulation results.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.428-431
• /
• 1990

This paper describes a pattern classification algorithm of QRS-complexes using significant point detection for extracting features of signals. Significant point extraction was processed by zero-crossing method, and decision function based on relational spectrum was used for pattern classification of the QRS-complexes. The hierarchical AND/OR graph was obtained by decomposing the signal, and by use of this graph, QRS's patterns were classified. By using the proposed algorithm, the accuracy of pattern classification and the processing speed were improved.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1978_1979
• /
• 2009

Heart rate may be a very important parameter in human health. To extract heart rate, the electrocardiogram(ECG) is commonly used. But the ECG acquisition procedure is somewhat complex. On the other hand, the acquisition of pulse wave or photoplethysmogram(PPG) is very easy. However, the peak of PPG is not so sharp as ECG. This study tries to enhance the performance of period detection in PPG signal. The method uses the average slopes around the main peak. The crossing point of the increasing and the decreasing slopes is selected as the peak point of heart rate period. The proposed method showed smoothed heart rate graph and reduced irregularity in heart rate values.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.6
• /
• pp.1194-1199
• /
• 2009

Heart rate may be a very important parameter in human health. To extract heart rate, the electrocardiogram(ECG) is commonly used. But the ECG acquisition procedure is very complex. On the other hand, the acquisition of pulse wave or photoplethysmogram(PPG) is very easy. However, the peak of PPG is not so sharp as ECG. This study tries to enhance the performance of peak detection in PPG signal. The method uses the average slopes around the main peak. The crossing point of the increasing and the decreasing slopes is selected as the peak point of heart rate period. The proposed method showed smoothed heart rate graph and reduced irregularity in heart rate values.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1360-1363
• /
• 1996

EPD(End Point Detection) is used to decide etching degree of layer which must be removed at wafer etching process in plasma etching process which is one of the most important process in semiconductor manufacturing. In this thesis, the method which detects malfunction of etching process in real-time will be discussed. Several EPD signal traces are collected in normal plasma etching condition and used as reference EPD signal traces. Critical points can be detected by applying differentiation and zero-crossing techniques to reference EPD signal. Mean and standard deviation of critical parameters which is memorized from reference EPD signal are calculated and these determine the lower and higher limit of control chart. And by applying statical control chart to EPD signals which are collected in real etching process malfunctions of process are detected in real-time. By means of applying this method to the real etching process we prove our method can accurately detect the malfunction of etching process and can compensate disadvantage of current industrial method.