• Journal of the Korean Wood Science and Technology
• /
• 제47권5호
• /
• pp.547-556
• /
• 2019

Thinned, small larch logs have small diameters and no value-added final use, except as wood chips, pallets, or fuel wood, which are products with very low economic value; however, their mechanical strength is suitable for structural applications. In this study, small larch logs were sawed, dried, and cut into square timbers (with a $90mm{\times}90mm$ cross section) that were laterally glued to form core panels used to manufacture cross-laminated timber (CLT) wall panels. The surface and back of these core panels were covered with 12-mm-thick structural plywood panels, used as cross bands to obtain three-ply CLT wall panels. This attachment procedure was conducted in two different ways: gluing and pressing (CGCLT) or gluing and nailing (NGCLT). The size of the as-manufactured CLT panels was $1,220mm{\times}2,440mm$, the same as that of the plywood panels. The final wall panels were tested under lateral shear force in accordance with KS F 2154. As the lateral load resistance test required $2,440mm{\times}2,440mm$ specimens, two CLT wall panels had to be attached in parallel. In addition, the final CLT panels had tongued and grooved edges to allow parallel joints between adjacent pieces. For comparison, conventional light-frame timber shear walls and midply wall systems were also tested under the same conditions. Shear walls with edge nail spacing of 150 mm and 100 mm, the midply wall system, and the fabricated CGCLT and NGCLT wall panels exhibited maximum lateral resistances of 6.1 kN/m (100%), 9.7 kN/m (158%), 16.9 kN/m (274%), 29.6 kN/m (482%), and 35.8 kN/m (582%), respectively.

• 항공우주시스템공학회지
• /
• 제13권2호
• /
• pp.51-59
• /
• 2019

이번 연구에서는 앞서 Part I [1]에서 수행한 단일-셀(single-cell) 모델에 이어, 시위 방향으로 비대칭성 단면을 가지는 다중-셀(multi-cell) 복합재료 박벽보(thin-walled beam) 모델을 선정하여, 단면의 형상에 대한 이론적인 동특성을 해석하였다. 이를 위해 와핑 구속 효과와 전단 변형 효과, 보의 테이퍼비와 단면비 등을 고려하였다. Part I에서와 마찬가지로 다중-셀 단면의 질량 및 강성 계수와 고유 진동수 등의 특성을 조사하였다. 특히, 다중-셀과 단일-셀 단면을 비교하고, 다중-셀 단면의 고유 진동수에 미치는 테이퍼비와 단면비의 영향을 비교 분석하였다. 또한, 단면의 비대칭성과 와핑 함수를 보정하지 않은 경우에 대해 그 결과를 비교하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2016년도 춘계학술대회
• /
• pp.363-366
• /
• 2016

본 논문에서는 보행자 검출 시, 교차 상황에서 발생하는 문제 해결을 위한 방법을 제안한다. 영상에서 특정 보행자를 검출하는 동안 다른 보행자와 교차하는 경우, 기존에 검출하던 보행자가 아닌 다른 보행자를 잘못 검출하는 문제가 발생한다. 문제 해결을 위해 제안하는 방법은 다음과 같다. 먼저, 검출할 특정 보행자를 bounding box로 선택하고 해당영역을 템플릿으로 추출한다. HOG를 이용하여 영상에서 보행자들을 검출하고, 후보영역으로 지정한다. 후보영역으로 지정된 보행자들을 앞서 템플릿으로 추출한 특정보행자와 비교하여 검출할 보행자를 최종 선택한다. 비교에는 템플릿 매칭, 히스토그램 비교와 LBP를 이용한다.

• Structural Engineering and Mechanics
• /
• 제41권2호
• /
• pp.285-297
• /
• 2012

An inverse approach is presented for calculating the flexibility coefficient of open-side cracks in the cross sectional of beams. The cracked cross section is treated as a massless rotational spring which connects two segments of the beam. Based on the Euler-Bernoulli beam theory, the differential equation governing the forced vibration of each segment of the beam is written. By using a mathematical manipulation the time dependent differential equations are transformed into the static substitutes. The crack characteristics are then introduced to the solution of the differential equations via the boundary conditions. By having the time history of transverse response of an arbitrary location along the beam, the flexibility coefficient of crack is calculated. The method is applied for some cracked beams with solid rectangular cross sections and the results obtained are compared with the available data in literature. The comparison indicates that the predictions of the proposed method are in good agreement with the reported data. The procedure is quite general so as to it can be applicable for both single-side crack and double-side crack analogously. Hence, it is also applied for some test beams with double-side cracks.

• Journal of Information Processing Systems
• /
• 제12권1호
• /
• pp.73-82
• /
• 2016

In cognitive radio networks (CRNs), the performance of the transmission control protocol (TCP) at the secondary user (SU) severely drops due to the mistrigger of congestion control. A long disruption is caused by the transmission of primary user, leading to the mistrigger. In this paper, we propose a cross-layer approach, called a CR-aware scheme that enhances TCP performance at the SU. The scheme is a sender side addition to the standard TCP (i.e., TCP-NewReno), and utilizes an explicit cross-layer signal delivered from a physical (or link) layer and the signal gives an indication of detecting the primary transmission (i.e., transmission of the primary user). We evaluated our scheme by implementing it onto a software radio platform, the Universal Software Radio Peripheral (USRP), where many parts of lower layer operations (i.e., operations in a link or physical layer) run as user processes. In our implementation, we ran our CR-aware scheme over IEEE 802.15.4. Furthermore, for the purpose of comparison, we implemented a selective ACK-based local recovery scheme that helps TCP isolate congestive loss from a random loss in a wireless section.

• Journal of Mechanical Science and Technology
• /
• 제16권6호
• /
• pp.785-798
• /
• 2002

A reliable analytic model that predicts the surface profile of the exit cross section of workpiece in round-oval (or oval-round) pass sequence is established. The presented model does not require any plasticity theory but needs the only geometric information on workpiece and roll groove. Formulation is based on the linear interpolation of the radius of curvature of an incoming workpiece and that of roll groove in the roll axis direction when the maximum spread of workpiece is known beforehand. The validity of the analytic model is examined by hot rod rolling experiment with the roll gap, specimen size, design parameter of oval groove and steel grade changed. Results revealed that the cross sectional shapes predicted by the model were in good agreement with those obtained experimentally. We found that the analytic model not only has simplicity and accuracy for practical usage but also saves a large amount of computational time in comparison with finite element method.

• 한국소음진동공학회논문집
• /
• 제20권6호
• /
• pp.568-576
• /
• 2010

It is widely known that the leak locating of underground plastic pipelines is much more difficult than that of cast iron pipelines. The precision of the leak locating depends upon the speed of leak signal and the time delay estimation between the two sensors on the pipeline. In this paper, six different windowing filters are considered to improve the time delay estimation especially for the plastic pipelines. The time delay is usually estimated from the peak time of cross-correlation functions. The filtering windows including rectangle, Roth, Wiener, SCOT, PHAT and maximum likelihood are applied to derive the generalized cross-correlation function and compared each other. Experimental results for the actual plastic underground water supply pipeline show that the introduction of the filtering windows improved the precision of time delay estimation. Some window functions provide excellent leak locating capability for the plastic pipe of 98 m long, which is less than 1 % of the pipe lengths. Also a new probabilistic approach that the combinations of all results from each filtering window is suggested for the better leak locating.

• 한국소음진동공학회논문집
• /
• 제27권1호
• /
• pp.80-86
• /
• 2017

This paper describes switching method of the cross-sectional area of the fluid passage way to improve the performance of a hydraulic engine mount with an inertia track and a decoupler. The mount has nonlinear dynamic characteristics depending on the vibrational frequency and amplitude. For the convenience of analysis, two linear motion equations were derived on the basis of the mechanical model according to the low-and high-frequencies. The properties of the transmissibility and dynamic stiffness derived from the equations were investigated according to switching the cross-sectional area of the inertia track and decoupler. Switching method of the cross-sectional area can be derived from the transmissibility plot. In comparison between transmissibility of passive and switchable mounts with an inertia track and a decoupler, the performance of the switchable mount is improved greatly than the passive mount. The resonant peak is remarkably reduced in the high frequency region.

• 치과방사선
• /
• 제27권1호
• /
• pp.7-16
• /
• 1997

This study was performed to demonstrate the method of image reformation for dental implants, using a personal computer with inexpensive softwares and to compare the images reformatted using the above method with those using Dentascan software. CT axial slices of 5 mandibles of 5 volunteers from GE Highspeed Advantage(GE Medical systems, U.S.A.) were used. Personal computer used for image reformation was PowerWave 6041120 (Power Computing Co, U.S.A.) and softwares used were Osiris (Univ. Hospital of Geneva, Switzerland) and Import ACCESS V1.H Designed Access Co., U.S.A.) for importing CT images and NIH Image 1.58 (NIH, U.S.A.) for image processing. Seven images were selected among the serial reconstructed cross-sectional images produced by Dentascan(DS group). Seven resliced cross-sectional images at the same position were obtained at the personal computer(PC group). Regression analysis of the measurements of PC group was done against those of DS group. Measurements of the bone height and width at the reformed cross-sectional images using Mac-compatible computer were highly correlated with those using workstation with Dentascan software(height : r²=0.999, p<0.001, width : r²=0.991, p<0.001). So, it is considered that we can use a personal computer with inexpensive softwares for the dental implant planning, instead of the expensive software and workstation.

• 한국가시화정보학회지
• /
• 제14권2호
• /
• pp.18-24
• /
• 2016

This paper presents an experimental investigation to visualize cross-sectional two-phase flow structure and identify liquid-gas interface for condensation of steam at a low mass flux in a slightly inclined tube using the axial-viewing technique, which permits to look directly into flow during condensation of steam. In this technique, two-phase flow is viewed along the axis of a pipe by locating a high-speed video camera in front of a viewer that is fitted at the outlet of the pipe. A short section of the pipe is illuminated and is recorded through the viewer, which is kept free of liquid by mildly introducing air. Experiments were conducted in a pipe of 19.05 mm in inner diameter at atmospheric pressure. Cross-sectional two-phase flow structure is obtained at a steam mass flux of $2.62kg/m^2s$ as a function of steam quality in the range from 0.5 to 0.9. The results show that stratified-wavy flow is a unique flow pattern observed in the scope of the present study. Condensate film thickness, stratification angle and void fraction were measured from the obtained flow structure images. Finally, heat transfer coefficient was calculated using the measurement data and discussed in comparison with existing correlations.