• 한국의류학회지
• /
• 제10권2호
• /
• pp.79-84
• /
• 1986

Methacrylic acid was graft polymerized with benzoyl peroxide in itiator onto the commercial PET film. Graft polymerization was carried out in emulsion, which consisted of BPO (1), chlorobenzene(8) as swelling agent, tween 80(1) and sodium lauryl sulfate(1) as emulsifier and water(1,000). Original PET film has poor reactivities and, so the film preswdled with benzyl alcohol($150^{\circ}C$, 1hr) was also examined. The graft yield of PET film was increased with reaction temperature and monomer concentration. The graft yield of preswelled PET film was higher than that of no-treated PET film. Moisture regain was linearly increased with graft yield. DSC thermodiagram showed the Tm of grafted PET film was same as that of original PET film. Grafted PET film was dyed with methylene blue solution. The photograph of the cross section showed that grafting was occured not at the center but near surfaces.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.418-418
• /
• 2012

We fabricated a new type of hybrid film using molecular layer deposition (MLD). The MLD is a gas phase process analogous to atomic layer deposition (ALD) and also relies on a saturated surface reaction sequentially which results in the formation of a monolayer in each sequence. In the MLD process, polydiacetylene (PDA) layers were grown by repeated sequential surface reactions of titanium tetrachloride and 2,4-hexadiyne-1,6-diol with ultraviolet (UV) polymerization under a substrate temperature of $100^{\circ}C$. Ellipsometry analysis showed a self-limiting surface reaction process and linear growth of the hybrid films. Polymerization of the hybrid films was confirmed by infrared (IR) spectroscopy and UV-Vis spectroscopy. Composition of the films was confirmed by IR spectroscopy and X-ray photoelectron (XP) spectroscopy. The titanium oxide cross-linked polydiacetylene (TiOPDA) hybrid films exhibited good thermal and mechanical stabilities.

• Bulletin of the Korean Chemical Society
• /
• 제19권3호
• /
• pp.328-332
• /
• 1998

Anionic ring-opening polymerization of 3,4-[(dimethylsilyl)isopropyl]benzo-1,1-dimethyl-1-silacyclopentene in the presence of n-butyllithium and HMPA in THF at - 78 ℃ afforded poly[3,4-(dimethylsilylisopropyl)benzo-1,1-dimethyl-1-silapentene]. The characteristic Si-H stretching frequency in the IR is observed at 2100 cm-1. The polycarbosilane has been modified by chloroplatinic acid catalyzed addition of styrene to the polycarbosilane SiH units. Molecular weights and thermal properties of the polymers were compared. The sol-gel polymerization of 3,4-[(dimethoxysilyl)isopropyl]benzo-1,1-dimethoxy-1-silacyclopentene in the presence of aqueous HCl or NaOH in THF resulted in a cross-linked polysiloxane. The xerogel has a low surface area of 13-14 m2/g and is stable up to about 400 ℃ with only 5% weight loss under a nitrogen atmosphere.

• Transactions on Electrical and Electronic Materials
• /
• 제10권1호
• /
• pp.9-15
• /
• 2009

There is a growing demand for a high voltage silicone rubber composite with high mechanical property and high electrical property. The effect of modified cross-linking agent on the mechanical, electrical properties, and short-circuit test performance of silicone rubber insulators have been investigated. To use base polymer, the various silicone polymers were prepared by the equilibrium polymerization. Aluminum trihydrate surface was treated by vinyl silane. Liquid silicone rubber nanocomposite was prepared from the compounding of VPMPS, HPDMS, catalyst, and alumina trihydrate modified with 1,3,5-trivinyl-l,3,5-trimethylcyclotrisiloxane. The mechanical property and electrical property for insulation materials were measured, indicating the high tensile strength and the good short-circuit property.

• 공업화학
• /
• 제21권6호
• /
• pp.621-626
• /
• 2010

음이온 교환막은 전기투석뿐만 아니라 역전기투석에 의한 전기생산과 축전 탈이온에 의한 정수 분야에 이용될 수 있다. 본 연구에서는 폴리비닐알콜 수용액 상에서 (vinylbenzyl)trimethylammonium chloride와 2-hydroxyethyl methacrylate를 중합한 후 글루타르산과의 에스테르화 반응, 그리고 글루타르알데히드와 가교반응을 통해서 음이온 교환막을 제조하였다. 실험 변수에 따라 음이온 교환막을 제조하고 이온교환막의 전기화학적 물성을 조사하였다. 중합반응에서 음이온 교환성 단량체 비율에 따라 이온교환량과 저항 값이 변하였으며, 에스테르화 반응에서는 글루타르산의 함량의 증가에 따라 함수율과 전도도가 감소하였다. 형성된 필름과 알데히드의 가교반응 시간 변화는 함수율, 전기저항, 이동수 값들에 영향을 미쳤다. 끝으로 제조된 이온 교환막의 chronopotentiometry와 한계전류밀도도 측정하였다.

• Restorative Dentistry and Endodontics
• /
• 제17권2호
• /
• pp.331-341
• /
• 1992

The purpose of this study was to measure the polymerization contraction stress of two types of composite resins; chemical cured type(Cliarfil F II, Kuraray, Japan) and photo-cured type(Photo-Clearfil Bright, Kuraray, Japan). The stresses of composite resin by contraction measured with specially designed measuring device(Fig. 1). The stresses caused by shrinkage during hardening of specimens were measured according to the type of composite resins, thickness of specimen(0.65, 1.30 and 1.95mm), and ratio of catalyst to base in case of only chemical cured composite resin(0.5, 1.0 and 1.5). As the composite resin specimen shrank on hardening, the load cell recorded force vs time automatically on pen-recorder(Toa, Japan) with a cross-head speed 60mm/hr at 0~10 voltages up to 2 hours. The experiments were conducted in a room maintained at $23{\pm}2^{\circ}C$ and relative humidity $50{\pm}10%$. The results were as follows. 1. The contraction stress during hardening was higher in photo cured composite resin than in chemical cured composite resin. 2. The contraction stress during hardening was increased with thickness of composite resin specimen. 3. In chemical cured composite resin, the polymerization contraction stress was decreased with ratio of catalyst and base. 4. The contraction stress during polymerization was higher in early time after insertion of photo cured composite resin and chemical cured composite resin.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.362-363
• /
• 2012

A new cross-linkable polymer, cross-linked d-PBAB, which has the triphenylamine as the hole transporting moiety and ethynyl group as the thermal cross-linker is firstly synthesized by the combination of anionic polymerization and deprotection process. The thermal cross-linking reaction was performed at $240^{\circ}C$ for 50 min and cross-linked d-PBAB layer showed smooth surface and is not soluble at organic solvent under spin-coating of emitting layer (EML). The solution-processed PLED which was fabricated with cross-linked d-PBAB as HTL showed approximately two times higher Lmax and four times higher LEmax than those obtained from PLED with PEDOT:PSS as the HTL. These result is ascribed to better ability of cross-linked d-PBAB to block electrons and to prevent exciton-quenching than those of PEDOT : PSS at the EML interface. This results strongly suggested that cross-linked d-PBAB can be a promising material to replace conventional PEDOT : PSS. It can be suspected that PLEDwith cross-linked d-PBAB would show longer lifetime compared with that of PLED with PEDOT : PSS, and thus further studies are under investigation.

• Bulletin of the Korean Chemical Society
• /
• 제27권7호
• /
• pp.1059-1062
• /
• 2006

• 접착 및 계면
• /
• 제19권2호
• /
• pp.74-82
• /
• 2018

아크릴레이트 기반의 점착제를 가교 시키는 기술은 다양하게 소개되어 왔다. 본 연구에서는 에폭시 변성 단량체와 메틸아지리딘 가교제를 활용하여 높은 가교 밀도를 가지는 아크릴 구조체를 만들었다. 베이스구조체를 제조하기 위해서 빠른 제조 공정이 가능하고 무용제 공정이 가능한 UV 중합 기술을 활용했다. FT-IR, 경화거동 및 접착특성 평가를 통해 UV경화도 및 2차경화 온도에 따른 특성 변화를 확인하고자 하였다. 겔분율은 선경화 $800mJ/cm^2$, 120도 후 경화온도 조건에서 50%이상 확보할 수 있었으며, 180도 경화조건에서 80%이상 확보 할 수 있었다. 경화 시간이 길어짐에 따라 경화도가 100%에 도달하였으며 이를 통해 열경화를 통한 2차 경화가 효과적임을 확인 할 수 있었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1419-1420
• /
• 2005

We have synthesized a photo patternable blue lightemitting polyfluorene (PF) derivative containing cross-linkable oxetane units. Poly(9,9-bis-(4-octyloxyphenyl)- fluorene-2,7-diyl-alt-9,9-bis-((3-hexyloxy-3'- ethyl)-oxetane)-fluorene-2,7-diyl) has been synthesized by Suzuki coupling polymerization. The relationship between patterning property and several variables such as the intensity of the exposed UV light, the concentrations of additives, has been studied by using optical microscope UV/visible spectroscopy, photoluminescence and scanning electron microscope (SEM). We obtained fine patterns with 10 mm resolution using the polymer film after exposure and development. This patterning method using conjugated polymers can be applicable to make fine pixels for PLEDs and OFETs.