• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 추계학술대회 논문집
• /
• pp.534-539
• /
• 2001

This paper presents the critical speed analysis of geogrid-reinforced rail roadbeds on soft soil. A rail roadbed on soft ground must be designed to avoid intolerable stress in the underlying soil and to give sufficient support for the rail system. At high speeds, the deformation of rail systems will gain dynamic amplification, and reach excessive values as a certain speed, here termed critical speed is approached. The elastic Winkler foundation model was used to predict the critical speed of geogrid-reinforced rail roadbeds on soft soil and the model properties were determined by the in-situ cyclic plate load test. Based on the parametric study of elastic beam on Winkler foundation model, the critical speed increase with the increase of the flexural risidity of subgrade EI and the stiffness coefficient of Winkler foundation k. From the in-situ cyclic load tests and analysis of elastic beam on Winkler foundation model, the critical speed increase with increase in number of reinforced layer and non-dimensional value for depth of first geogrid layers and the thickness of reinforced rail roadbed u/d.

• 한국유체기계학회 논문집
• /
• 제4권2호
• /
• pp.22-28
• /
• 2001

This study was performed to evaluate the dynamic behavior of turbo pump unit. The acceptable separate margin of $1^{st}$ critical speed was obtained by the use of elastic-ring inserted ball bearing, while the poor separate margin of $1^{\st}$ critical speed was appeared in the case without the elastic-ring. In addition, the results show that the stiffness and damping of plain seals give more separate margin of $2^{nd}$ critical speed. However the wear or the failure of seals could reduce the $2^{nd}$ critical speed near the operating speed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.593-598
• /
• 2000

In this paper the critical speed analysis and design sensitivity investigation are carried out with an APU(auxiliary power unit) gas turbine having a spline shaft connection. The DDM(direct differential method) is directly applied to formulate the critical speed design sensitivity problem of a general nonsymmetric-matrix rotor-bearing system. The design sensitivity analysis have shown that the critical speed change rate to the support modeling of the spline shaft connection point is extremely negligible, and thereby its design uncertainty is lifted. It has also been confirmed that the critical speeds up to the 4th are not sensitive to the design stiffness coefficients of 4-main bearings or supports, including two air foil bearings. Further, the critical speed change rate to the shaft-element length have shown quantitatively that the spline shaft has some limited influence on the 4th critical speed.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.9-14
• /
• 2017

This paper presents a rotordynamic analysis and the operation of a power turbine applied to a 250 kW super-critical $CO_2$ cycle. The power turbine consists of a turbine wheel and a shaft supported by two fluid film bearings. We use a tilting pad bearing for the power turbine owing to the high speed operation, and employ copper backing pads to improve the thermal management of the bearing. We conduct a rotordynamic analysis based on the design parameters of the power turbine. The dynamic coefficients of the tilting pad bearings were calculated based on the iso-thermal lubrication theory and turbine wheel was modeled as equivalent inertia. The predicted Cambell diagram showed that there are two critical speeds, namely the conical and bending critical speeds under the rated speed. However, the unbalance response prediction showed that vibration levels are controlled within 10 mm for all speed ranges owing to the high damping ratio of the modes. Additionally, the predicted logarithmic decrement indicates that there is no unstable mode. The power turbine uses compressed air at a temperature of $250^{\circ}C$ in its operation, and we monitor the shaft vibration and temperature of the lubricant during the test. In the steady state, we record a temperature rise of $40^{\circ}C$ between the inlet and outlet lubricant and the measured shaft vibration shows good agreement with the prediction.

• Journal of Mechanical Science and Technology
• /
• 제14권6호
• /
• pp.590-596
• /
• 2000

Cause of excessive vibration with twice the rotational speed of a two-pole generator rotor for the fossil power plants was investigated. The two-pole generator rotor, treated as a typically asymmetric rotor in vibration analysis, produces asynchronous vibration with twice the rotational speed, sub-harmonic critical speeds, and potentially unstable operating zones due to its own inertia and/or stiffness asymmetry. This paper introduces a practical balancing procedure, and presents the results of the investigation on sources of the excessive vibration based on the experimental vibration data of the asymmetric two-pole rotor in balancing.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1995년도 추계 학술대회논문집
• /
• pp.126-131
• /
• 1995

In this paper we study steady capillary-gravity waves in a two-layer fluid bounded above by a free surface and below by a horizontal rigid boundary with a small obstruction, Two critical speeds for the waves are obtained. Near the smaller critical speed, the derivation of the usual forced KdV equation (FKdV) fails when the coefficient of the nonlinear term in the FKdV vanishes. To overcome this difficulty, a new equation called a forced extended KdV equation (FEKdV) governing interfacial wave forms is obtained by a refined asymptotic method. Various solutions and numerical results of this equation are presented.

• 소음진동
• /
• 제10권1호
• /
• pp.74-81
• /
• 2000

The vibrational model of a helical gear pair is developed with considering the elastic deformation of the active teeth and the body to be a rigid. The main source of vibration in geared system which has been known to be the gear transmission error is mathematically formulated and used for the analysis of vibrational characteristics of geared system. As an example, a simple geared system containing a helical gearing is considered. The critical speeds are found by the campbell diagram and compared with the experimental results.

• 한국소음진동공학회논문집
• /
• 제19권5호
• /
• pp.537-544
• /
• 2009

In order to increase the critical speed of rotating disks of which functional material could not be changed such as in optical and magnetic data storage disks, a new disk with a rim reinforced by composite material is proposed and its concept is verified by numerical analysis. Stress distributions are found for the rotating disk composed of two annular disks of which materials are isotropic inside and orthotropic outside. Dynamic equation is formulated in order to calculate the natural frequency and critical speed. For the solution of lateral vibration, a rotational symmertry condition is applied along circumferential direction and a finite element interpolation with Hermite polynomial is performed along the radial direction to obtain a proper solution. According to the results, reinforcing a disk at rim makes critical speeds drastically increased, and induces a buckling phenomenon in mode (0,0) which occurs over the lowest critical speed.

• 한국소음진동공학회논문집
• /
• 제16권2호
• /
• pp.169-175
• /
• 2006

Rotating annular disks are widely used in data storage devices such as CDs, DVDs(digital versatile disks), and HDs(hard disks). Higher data transfer rate in data storage disks could not be achieved by polycarbonate disks in the present market. The problem can be solved by applying the fiber-reinforce composite materials to the disks. In this paper, an application of composite materials to rotating disks is proposed to increase the critical speed. Dynamic equation is formulated in order to calculate the natural frequency and critical speed for rotating composite disks by the Galerkin method. The orthogonal functions are used in series solution. A companion paper(Part II) presents and discusses the numerical results of vibration analysis and critical speed for rotating polar orthotropic disk using the formulation and solution method given in this paper (Part I).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.513-518
• /
• 2001

This research has been performed to estimate the hunting motion hysteresis of railway passenger cars. An old and a new car with almost same structure are chosen as analysis models. To solve effectively a set of simultaneous equations of motion strongly coupled with creep relations, shooting algorithm in which the nonlinear relations are regarded as a two-point boundary value problem is adopted. The bifurcation theory is applied to the dynamic analysis to distinguish differences between linear and nonlinear critical speeds by variation of parameters. It is found that there are some factors and their operation area to make nonlinear critical speed respond to them more sensitivity than linear critical speed. Full-scale roller rig tests are carried out for the validation of the numerical results. Finally, it is concluded that the wear of wheel profile and the stiffness discontinuities of wheelset suspension caused by deterioration have to be considered in the analysis to predict hysteresis of critical speed precisely.