• 한국유체기계학회 논문집
• /
• 제13권3호
• /
• pp.18-23
• /
• 2010

This paper predicts the unbalance and transient (start-up) response of a 5MW industrial gas turbine by using commercial rotordynamic tool, DYNAMICS 4.3. The gas turbine is operated at 12,975rpm on squeeze film dampers or tilting pad bearings. The stiffness and damping coefficients of the squeeze film dampers and tilting pad bearings are estimated. It is seen that the vibration amplitude of the gas turbine rotor is sufficiently small around the critical speeds and at the rated speed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.533-538
• /
• 2001

This paper describes a combinational method to compute the global and local solutions of optimization problems. The present hybrid algorithm uses both a genetic algorithm and a local concentrate search algorithm (e. g simplex method). The hybrid algorithm is not only faster than the standard genetic algorithm but also supplies a more accurate solution. In addition, this algorithm can find the global and local optimum solutions. The present algorithm can be supplied to minimize the resonance response (Q factor) and to yield the critical speeds as far from the operating speed as possible. These factors play very important roles in designing a rotor-bearing system under the dynamic behavior constraint. In the present work, the shaft diameter, the bearing length, and clearance are used as the design variables.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.56-61
• /
• 2012

The dynamic instability and natural frequency of axially moving beam with an attached mass are investigated. Thus, the effects of an attached mass on the stability of the moving beam are studied. The governing equation of motion of the moving beam with an attached mass is derived from the extended Hamilton's principle. The natural frequencies are investigated for the moving beams via the Galerkin method under the simple support boundary. Numerical examples show the effects of the attached mass and moving speed on the stability of moving beam. Moreover, the lowest critical moving speeds for the simple supported conditions have been presented. The results can be used in the analysis of axially moving beams with an attached mass for checking the stability.

• Journal of Mechanical Science and Technology
• /
• 제19권4호
• /
• pp.985-992
• /
• 2005

Vehicle Stability Control (VSC) system prevents vehicle from spinning or drifting out mainly by braking intervention. Although a control threshold of conventional VSC is designed by vehicle characteristics and centered on average drivers, it can be a redundancy to expert drivers in critical driving conditions. In this study, a manual adaptation of VSC is investigated by changing the control threshold. A control threshold can be determined by phase plane analysis of side slip angle and angular velocity which is established with various vehicle speeds and steering angles. Since vehicle side slip angle is impossible to be obtained by commercially available sensors, a side slip angle is designed and evaluated with test results. By using the estimated value, phase plane analysis is applied to determine control threshold. To evaluate an effect of control threshold, we applied a 23-DOF vehicle nonlinear model with a vehicle planar motion model based sliding controller. Controller gains are tuned as the control threshold changed. A VSC with various control thresholds makes VSC more flexible with respect to individual driver characteristics.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.551-555
• /
• 1996

The continuing demand for quality products requires better understanding and improved control of the production process. And, in recent year requirements for flatness control in strip rolling have become increasinglysevere because of the control for flatness of cold rolled strip is essential for further down stream processing. Also a speeds of rolling mills to meet productivity requirements puts a demanding requirement on the control of flatness of rolled strip. The demands on a total flatness control system therefore are a measuring and indication system consisting of a measuring roll that is robust, accurate, reliable and require a minimum of maintenance. The critical prt of any control system is the quality of the information being provided by the measurement instrument or device. It is therfore of utmost importance to have an accurate, repeatable and reliable measuring system. So, in this paper, The measuring roll for automatic flatness control system of contact type has been investigated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.552-558
• /
• 2001

When operating lathe gear box which is equipped with geared transmission, it sometimes generates loud noise and excessive vibrations. In order to identify their causes, in this study, torsional and lateral vibration characteristics including critical speeds of the gear transmission system are firstly analyzed using lumped parameter models. Natural frequencies and mode shapes of the gear box structure are also analyzed by using the modal test. Furthermore, measured vibration and noise signals during operations are analyzed and compared with theoretical analysis results. After all, it is concluded that the primary cause of the excessive noise and vibrations is the resonance between gear meshing frequency including its side bands, the frequencies of shaft bending and torsional vibrations, and the natural frequencies of the gear box structure. Consequently the noise and vibration levels are greatly reduced by avoiding resonance between the natural frequencies and gear meshing frequencies through the rearrangement of the gears on the transmission shaft without any gear ratio change.

• Smart Structures and Systems
• /
• 제4권4호
• /
• pp.429-438
• /
• 2008

The aim of this paper is to define the required measurements and processing tools necessary for developing a maintenance approach applied to rotating machines in the presence of multiple faults. The system responses measured were accelerations and transmission errors. Acceleration measurements provide most of the information on bearing conditions, while transmission error measurements provide pertinent information on gear conditions. The measurements were carried out for several operating conditions (loads and speeds). System responses were processed in several analyzing domains (Time, Spectrum, and Cepstrum domains). The approach developed enables the detection and identification of combined faults and it can be applied to other types of rotating machines once the critical elements and their associated faults have been defined.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2006년도 특별논문집
• /
• pp.71-76
• /
• 2006

Preliminary conceptual design of hulls is developed and a theoretical evaluation study performed for the comparison of the hull concepts. Systematic variation of the side hull location is carried out to find an optimum position of side hulls for a trimaran by CFD computation. In order to compare computed results, the model test of trimaran was carried out. Shallow water effect is considered due to the route which has critical water depth of 20m for the design speed and investigated on the condition of different speeds and water depth by the numerical computations.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1450-1454
• /
• 2000

In order to understand dynamic characteristics of centrifugal compressor supported foil bearing, of which normal operating speed is about 20,000 ${\sim}$ 50,000 rpm, the rotor whirl is measured using gap sensors. Not only critical speeds of rotor system but also stability of rotor whirl, which are main concerns of the turbo compressor system, are measured using gap sensors by varying the rotating speed the rotor. The stiffness characteristics of bearing system is shown to be almost invariant according to speed variation by the measurement of eccentricity. In addition, from the directional power spectral density function of the measured vibration signal, the isotropy stiffness characteristics of foil bearing system is discussed.

• 한국소음진동공학회논문집
• /
• 제22권5호
• /
• pp.407-412
• /
• 2012

The dynamic instability and natural frequency of an axially moving pipe conveying fluid are investigated. Thus, the effects of fluid velocity and moving speed on the stability of the system are studied. The governing equation of motion of the moving pipe conveying fluid is derived from the extended Hamilton's principle. The eigenvalues are investigated for the pipe system via the Galerkin method under the simple support boundary. Numerical examples show the effects of the fluid velocity and moving speed on the stability of system. Moreover, the lowest critical moving speeds for the simply supported ends have been presented.