• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.1
• /
• pp.32-41
• /
• 2006

In this study, the thrust generation by simultaneous flapping airfoils in tandem configuration is parametrically studied with respect to flapping frequency, amplitude and relative location. Navier-Stokes solver with overset grid topology is employed to calculate the unsteady flowfields. The computation results indicate that when the two airfoils stroke in-phase - flapping phase lag is zero - the maximum propulsive efficiency and thrust can be obtained for most frequency and amplitude range. At a flapping amplitude of 0.2 chord and a reduced frequency of 0.75, the propulsive efficiency of aft airfoil is enhanced by about 37 % compared with that of forward airfoil. However, if flapping frequency exceeds some critical value, the strength of the leading edge vortex of aft airfoil is fortified by the trailing edge vortex of the forward airfoil, resulting in poor propulsive efficiency. It is also found that out-of-phase flapping has relatively low propulsive efficiency and thrust since vortical wake of the forward airfoil interacts with the leading edge vortex of aft airfoil in the unfavorable fashion. The total thrust and propulsive efficiency are shown to decrease with the horizontal miss distance of the aft airfoil. On the contrary, the vertical miss distance has little effect on the overall aerodynamic performance.

• Journal of Korean Society of Forest Science
• /
• v.104 no.2
• /
• pp.267-276
• /
• 2015

This study suggests a macroscopic method of evaluating forest recreation function based on physical characteristics of forests. The method was verified by a correlation between forest recreation function in popular top 45 mountains and popularity among them, with using data-mountain area, height, distance between mountain and cities, population around mountain, and size of public service. According to analysis of the forest recreation function, it is shown that top 8 mountains, including Jirisan and Seoraksan, provide over 64% of total recreation function, while they serve the function relatively lower than mountains near mega cities-Bukhansan in Seoul-do, in terms of the function per unit area ($km^2$). It is because, in a case of national and provincial mountains, the size of mountain is likely a critical factor for determining recreation function and the distance influences on it relatively lower. These findings implicate that a large size of forests bring the recreation function to visitors on nationwide level, whileas forests in suburban provide intensively it to near population to near population.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.8-14
• /
• 2011

The optimal geometry of the gate field plate in AlGaN/GaN-on-Si HEMT has been proposed using two-dimensional device simulation to achieve a high breakdown voltage for a given gate-to-drain distance. It was found that the breakdown voltage was drastically enhanced due to the reduced electric field at the gate corner when a gate field plate was employed. The electric field distribution at the gate corner and the field plate edge was investigated as functions of field plate length and insulator thickness. According to the simulation results, the electric field at the gate corner can be successfully reduced even with the field plate length of 1 ${\mu}m$. On the other hand, when the field plate length is too long, the distance between field plate and drain electrode is reduced below a critical level, which eventually lowers the breakdown voltage. The highest breakdown voltage was achieved with the field plate length of 1 ${\mu}m$. According to the simulation results varying the $SiN_x$ film thickness for the fixed field plate length of 1 ${\mu}m$, the optimum thickness range of the $SiN_x$ film was 200 - 300 nm where the electric field strength at the field plate edge counterbalances that of the gate corner.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.2
• /
• pp.212-234
• /
• 1999

Dental restorative materials must have the physical properties to withstand wear and corrosion. Base metal alloys possess better mechanical properties and lower price than the gold alloys. For these reasons such alloys have largely replaced the precious metal alloys. One aspect to con-sider is the release of metal substances to oral environment. The release of elements from dental alloys is a continuing concern because the elements may have the potentially harmful biological effects on local tissues. The purpose of this study was to minimize metal release on the nonprecious metal surfaces by ion beam assisted deposition(IBAD) of titanium nitride (TiN) Ni-Cr-Be alloys with and without TiN coatings were secured in an wear test machine opposing ruby ball to determine their relative resistance to wear with loom, 200m, 300m and 400m sliding distance. And the corrosion behavior of the Ni-Cr-Be alloys with and without TiN coatings and 3 dental noble alloys have been studied. Potentiodynamic curves were used to analyse the corrosion characteristics of the alloys. The measurement of the released Ni and Cr ions was conducted by analysis of the electrolyte solution with atomic absorption spectroscopy. The results were as follows : 1. The critical sliding distance that wore down TiN coatings of $2.5{\mu}m$ thickness in this study condition was 300m. 2. Ion beam assisted deposition of TiN showed a good surface modification with respect to the properties of wear and corrosion resistance. 3. X-ray diffraction showed that the strongest peak of TiN is TiN(111) in the coatings. 4. The release of Ni and Cr ions from alloys measured by means of atomic absorption spectroscopy was reduced by ion beam assisted deposition of TiN.

• Explosives and Blasting
• /
• v.41 no.4
• /
• pp.1-8
• /
• 2023

On August 4, 2020, 2750 tons of ammonium nitrate stored in a storage warehouse at the Port of Beirut exploded. This explosion is said to be the largest ammonium nitrate explosion ever. By applying the TNT equivalency method, TNT equivalent amount corresponding to the explosion energy of 2750 tons of ammonium nitrate was calculated, and it is found to be 856 tons. Overpressure and impulse were calculated in a range up to 3600 m from the blast using the Kingery-Bulmash explosion parameter calculator tool. As the distance from the explosion center increases, the overpressure and impulse decrease exponentially, but the overpressure decreases more significantly, showing that overpressure is more affected by distance than the impact. As a result of applying the damage criteria to evaluate the effects of overpressure and impulse on the structure, the critical distances at which partial collapse, major damage, and minor damage to the structure occur are found to be approximately 500, 800, and 2200 m from the center of the explosion, respectively. The probit function was applied to evaluate the probability of damage to structures and human body. The points where the probability of collapse, major damage, minor damage, and breakage of window-panes to structures are greater than 50% are found to be approximately 500, 810, 2200, and 3200 m, respectively. For people within 200 m from the center of the explosion, the probability of death due to lung damage is more than 99%, and the 50% probability of eardrum rupture is approximately 300 m. The points with a 100% probability of death due to skull rupture and whole body impact due to whole body displacement are evaluated to be 300 and 100 m, respectively.

• Journal of the Korean Institute of Gas
• /
• v.28 no.1
• /
• pp.73-84
• /
• 2024

In this study, a quantitative risk impact assessment is performed using an ALOHA program to identify the risks when applying ammonia as fuel for combined cycle power plants as one of the solutions of climate change. The worst and the alternative accident scenarios are established for the Sejong combined cycle power plant and the effective ranges are calculated in terms of flammability, thermal radiation, overpressure and toxicity. The analysis results show that the toxic risk is the most critical and the effective distance is highly proportional to the mixing ratio of natural gas and ammonia by showing the Pearson's correlation coefficient over 98% as 0.991, 0.987 and 0.989 for the Level Of Concern(LOC)-1, LOC-2 and LOC-3, respectively. In addition, the coefficients of linearity for LOC-1, LOC-2 and LOC-3 are calculated to 133, 70 and 29, respectively so it can be confirmed that the effective distance increases as the criterion decreases.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.28 no.1
• /
• pp.41-57
• /
• 1983

The effect of temperature 'during the reduction division stage on the Indica-Japonica rice varieties were studied in artificial temperature-controlled cabinets (Bioclimatic Laboratory). Varieties used were indica-japonica crosses (Suweon 264, Suweon 258, Milyang 29), indica (IR36, Lengkwang) and japonica rice (Jin-heung). The results obtained from this study are summarized as follows. The most sensitive stage to low temperature, the tetrad stage, was observed in each variety with the following auricle distance: Jinheung, -12cm; IR36, -3cm; Suweon264, -9cm; Suweon258, -3cm; Milyang29, -6cm and Lengkwang, +1cm. The tetrad stage occured when the palea elongation was about 50 to 60% of the final palea length at flowering stage in all varieties. The percentage of degenerated spikelets at tetrad as influenced by low-temperature treatment was very low in Jinheung and Lengkwang, but very high in IR36. In indica-japonica crosses only the 7-days treatments had a very high percentage. Between the 4-day and 7-day treatments as well as among all varieties, clear differences were observed in the low temperature induced sterility of 'special spikelets' (upper position grains at tetrad). In the 7-day treatments except in Lengkwang, all varieties showed very high sterility. It appears that the treatments is over the critical limit for treatment. However in the 4-day treatments, the intervarietal differences in sterility were very clear. In Jinheung, sterility was 46.8%; IR36, 67.6%; Suweon264, 60.9%, Milyang29, 62.2%; Lengkwang, 27.8%. A close relationship was observed between fertility and auricle distance. The lowest fertility of special spikelets was at the tetrad stage and the first contraction phase. Before and after the stage there was an increase in fertility. The palea length elongated nearly in a straight line from the spikelet formation stage to flowering. And there was a high correlation between palea length and auricle distance. distance.

• Journal of the Korean Geographical Society
• /
• v.47 no.5
• /
• pp.755-774
• /
• 2012

The main objective of the study is to propose GIS-based methods to assess the population distribution criteria for undesirable facilities such as nuclear power plants. First of all, a review of the relevant criteria was conducted for the official documents compiled by such institutions as IAEA (International Atomic Energy Agency), U.S. NRC (Nuclear Regulatory Commission), and some national institutes including the Korea Institute of Nuclear Safety. It is informed from the review that the fundamental principle underlying the various criteria is to maximize the distance between a plant and the nearest population center. It is realized that two interrelated GIS-based techniques need to be devised to put the principle into practice; sophisticated ways of representing population distribution and identifying population centers. A dasymetric areal interpolation is proposed for the former and cell-based and area-based critical density methods are introduced. Grid-based population distributions at various spatial resolutions are created by means of the dasymetric areal interpolation. By applying the critical density methods to the gridded population distribution, some population centers satisfying the population size and density criteria can be identified. These methods were applied to the case of the Gori-1 nuclear power plant and their strengths and limitations were discussed. It was revealed that the assessment results could vary depending upon which method was employed and what values were chosen for various parameters. This study is expected to contribute to foster the applications of methods and techniques developed in geospatial analysis and modeling to the site selection and evaluation.

• Journal of Food Hygiene and Safety
• /
• v.14 no.3
• /
• pp.293-304
• /
• 1999

The purpose of this study was to evaluate the microbiological quality, and to assure the hygienic safety of the food production in the university food service facility located in Seoul in accordance with the Hazard Analysis Critical Control Point(HACCP) concepts. In the hygienic state assessment of kitchen, it has revealed that it was very important to remove water from the kitchen floor and to establish standard method for disinfection of cooking utensils. And foodservice workers were required to have training program for the safe handling of food and utensils since they did treat food without hygienic gloves. The kitchen layout had to be improved because the near distance of table with heating unit and shelf might cause the growth of microorganisms when prepared food was kept on the shelf. In terms of the timetemperature measurement and microbiological quality assessment during each of the food production phases, most of sengchae (raw vegetable dish) and namul (cooked vegetable dish) were treated within danger zone for food safeness ($5~60^{\circ}C$). It has shown that the microbiological quality of raw materials was very much inferior at the time of receiving based on the TPC($10^{5}~10^{7}$), coliform($10^{3}~1O^{6}$), which was not acceptable level(TPC:$10^{6}$, coliform:$10^{3}$) suggested by Solberg. Microbiological growth has increased in the both of sengchae and namul considerably during most of food production phase. Therefore, it is extremely important to reduce holding and serving time and to avoid treating food within the danger zone for food safeness. In addition, the prevention of cross-contamination during mixing the ingredients with improper equipments and with insanitary treatments by workers was also important to keep the food safety in this speciqic university foodservice facility.

• Journal of the Mineralogical Society of Korea
• /
• v.29 no.4
• /
• pp.209-220
• /
• 2016

Clay minerals are a major player to determine geochemical cycles of trace metals and carbon in the critical zone which covers the atmosphere down to groundwater aquifers. Molecular dynamics (MD) simulations can examine the Earth materials at an atomic level and, therefore, provide detailed fundamental-level insights related to physicochemical properties of clay minerals. In the current study, we have applied classical MD simulations with clayFF force field to dioctahedral clay minerals (i.e., gibbsite, kaolinite, and pyrophyllite) to analyze and compare structural parameters (lattice parameter, atomic pair distance) with experiments. We further calculated vibrational power spectra for the hydroxyls of the minerals by using the MD simulations results. The MD simulations predicted lattice parameters and interatomic distances respectively deviated less than 0.1~3.7% and 5% from the experimental results. The stretching vibrational wavenumber of the hydroxyl groups were calculated $200-300cm^{-1}$ higher than experiment. However, the trends in the frequencies among different surface hydroxyl groups of each mineral was consistent with experimental results. The angle formed by the surface hydroxyl group with the (001) plane and hydrogen bond distances of the surface hydroxyls were consistent with experimental result trends. The inner hydroxyls, however, showed results somewhat deviated from reported data in the literature. These results indicate that molecular dynamics simulations with clayFF can be a useful method in elucidating the roles of surface hydroxyl groups in the adsorption of metal ions to clay minerals.