• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.735-739
• /
• 2003

This paper presents a direct seek control algorithm for swing-arm type dual stage servo system that consists of a coarse actuator and a fine actuator. The proposed scheme is to design a control system that attenuates the effect of dynamic coupling between the two actuators so that the seek operation can be performed in a single-shot with stability. In an optical drive system with dual stage servo mechanism, the effect of dynamic coupling between the two actuators needs to be handled during the coarse seek operation due to its inherent structure. In an extreme case, the two actuators can collide each other, which leads to critical degradation of the seek performance. To handle this problem, our proposed control scheme is to generate the drive signals such that the two actuators behave as if they are a single fixed body. To this end, a feedforward controller and two feedback controllers are designed that enable the current drive system perform wide range of track seek. Simulation results are provided to show the validity and feasibility of our proposed algorithm.

• Progress in Superconductivity and Cryogenics
• /
• v.24 no.4
• /
• pp.16-24
• /
• 2022

Applications of REBa₂Cu₃O_7-δ tapes require joints with a simple manufacturing process, low resistance and good mechanical properties. In the present study, we successfully developed a copper diffusion joint between Cu-stabilized REBa₂Cu₃O_7-δ tapes that meets the above requirements without solder simply by applying flux, heat and pressurization. After a 3 min thermocompression process at approximately 150 δ and 336 MPa in air, two tapes were directly connected between Cu stabilizers by copper diffusion, which was proven by microstructure analysis. The specific resistivity of the copper diffusion joint reached 5.8 nΩ·cm² (resistance of 0.4 nΩ for a 306 mm splicing length) at 77 K in the self-field. The axial tensile stress reached 200 N without critical current degradation. The results show promise for the preparation of copper diffusion joints to be used in coils, attached tapes, and wire/cable terminals.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.3
• /
• pp.5-8
• /
• 2006

The effect of annealing time in Metal Organic Deposition(MOD) method was investigated at reduced total pressure. As the total annealing pressure was reduced, the growth rate of YBCO films increased from 0.14nm/sec at atmospheric pressure to 4.2nm/sec at 1 Torr. For the total pres sure of 700, 500, 300, 100, and 1 Torr, the optimal annealing times of 60, 40, 20, 10, 2minutes were found in our experimental conditions. When the an nealing time was short, poor crystallinity or un-reacted phase was obtained. Also, the degradation of YBCO films occurred when exposed longer to the humid ambient at the high annealing temperature. The reduced pressure was found effective to in crease the growth rate and to control the pore size of the YBCO films in MOD method. A fast growth of MOD-YBCO films was realized with high critical current density over $1MA/cm^2$ using reduced pressure annealing. Large pores, usually observed at atmospheric pressure in MOD method, disappeared and also, the number of pores was reduced.

• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4422-4430
• /
• 2022

Studying the effects of gamma radiation on the instrumentation and control (I&C) system of a nuclear power plant is critical to the successful and reliable operation of the plant. In the accidental scenario, the adverse environment of ionizing radiation affects the performance of the I&C system and it leads to inaccurate and incomprehensible results. This paper reports the effects of gamma radiation on the AT89C51RD2, a commercial-off-the-shelf 8-bit high-performance flash microcontroller. The microcontroller, selected for the device under test for this study is used in the remote terminal unit for a nuclear power plant. The custom circuits were made to test the microcontroller under different gamma doses using a ⁶⁰Co gamma source in both ex-situ and in-situ modes. The device was exposed to a maximum dose of 1.5 kGy. Under this hostile environment, the performance of the microcontroller was studied in terms of device current and voltage changes. It was observed that the microcontroller device can operate up to a total absorbed dose of approximately 0.6 kGy without any failure or degradation in its performance.

• Korean Journal of Materials Research
• /
• v.5 no.5
• /
• pp.598-605
• /
• 1995

Thin films of $YB_{2}Cu_{3}O_{7-d}$ were prepared on various substrated of MgO(100), $SrTiO_{3}$, and $LaAlO_{3}$ by using off-axis magentron sputtering methods and annealing in-situ. The prarameters of film fabrication processes had been optimized through a "follow the lcoal maxima" strategy to yield good quality films in therms of the critical temperature $T_{c}$ and the critical current density $J_{c}$. Optimizedproecsses employing a plane magndtron and an cylindrical magnetron yielded $T_{c}$>90K along with $J_{c}$$10^{6}$A/$\textrm{cm}^2$ at 77K and > 2${\times}$$10^{7}$A/$\textrm{cm}^2$ at 5K. The sampels, however, showed degradationinthe properties, after chemical etching for fabrication of microbridges with the line width of 2-10 mocrons. In particular, the value of $T_{c}$ for the microbridges of 2microns was as small as 80%. The degradation was strongly dependent on the line width through a formula : $T_{c}$(e)=$T_{c}$)b) [1-a exp(-1000 bL)} where $T_{c}$(e) and $T_{c}$ (b) are the values of $T_{c}$ in the absolute scale measured after and before chemical etching, respectively and L is the line width in mm. By utilizing a best fitting technique, the proper constant values of a and to b were found as exp(-1.2) and 0.22, respectively. This formula was very useful in estimatiing the upper limit of the device operationtemperature.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.2
• /
• pp.280-285
• /
• 2021

When VNDN technology is used as a communication technology for infotainment application services of connected vehicles, it is possible to realize data-centric networking technology in which data is the subject of communication.Vehicle security attacks and hacks, performance degradation during long-distance data transmission, and frequent data loss It is possible to innovate the limitations of the current host-oriented Internet-based infotainment application service technology of connected vehicles. The data packet forwarding issue to deliver critical information data that is very sensitive to delay in the VNDN on a push-based basis to RSU (Road Side Unit), etc. is one of the issues to be solved for realizing VNDN-based application services. We comprehensively analyze existing forwarding techniques to support push-based data traffic under the environment, and compare and analyze each technique in terms of performance.

• Progress in Superconductivity and Cryogenics
• /
• v.22 no.3
• /
• pp.7-12
• /
• 2020

Electromechanical properties of REBCO CC tapes are known to be limited by defects (cracks) that form in the brittle REBCO layer. These defects could be inherently acquired during the CC tapes' manufacturing process, such as slitting, and which can be initiated at the CC tapes' edges. If propagated and long enough, they are believed to cause critical current degradation and can substantially decrease the delamination strength of CC tapes. Currently, commercially available CC tapes from various manufacturers utilize different growth techniques for depositing the REBCO layers on the substrates in their CC tapes preparation. Their epitaxial techniques, unfortunately, cannot perfectly avoid the formation of particles, in which sometimes acts as current blocking defects, known as outgrowths. Collective research regarding the composition, size, and formation of these particles for various CC tapes with different deposition techniques are particularly uncommon in a single study. Most importantly, these particles might interact in one way or another to the existing cracks. Therefore, systematic investigation on the interactions between the cracks' development mechanism and particles on the REBCO superconducting layers of practical CC tapes are of great importance, especially in the design of superconducting devices. Here, a proper etching process was employed for the CC tapes to expose and observe the REBCO layers, clearly. The scanning electron microscope, field emission scanning microscope, and energy-dispersive x-ray spectroscopy were utilized to observe the interactions between cracks and particles in various practical CC tapes. Particle compositions were identified whether as non-superconducting or superconducting and in what manner it interacts with the cracks were studied.

• Journal of Internet Computing and Services
• /
• v.11 no.4
• /
• pp.143-158
• /
• 2010

The illegal leakage of enterprise digital confidential information will threaten the enterprise with bankruptcy. Today since most small-and-medium companies have no capability to fight against illegally compromising their critically confidential documents in spite of knowing the leakage of them, strongly safe distribution system of the digital confidential documents should be designed so in secure as to prevent any malicious intent of embezzlement from accessing the critical information. Current DRM-based protection system is not always perfect to protect the digital secrets, even seems to leave the secrets open. Therefore our study has analyzed the illegal leakage paths that hackers attack against and the vulnerability of the current protection systems. As result, we study the group communication based system architecture satisfying the security conditions to make even legitimate working employee keep out of the confidential documents, without performance degradation. The main idea of this architecture is to stay every secrets in encrypted form; to isolate the encrypted documents from the crypto-key; to associate every entity with one activity and to authenticate every entity with DSA-based public key system; multiple authentication method make hackers too busy to get a privilege to access the secrets with too many puzzle pieces. This paper deal with the basic architectural structure for the above issues.

• Journal of Electrochemical Science and Technology
• /
• v.5 no.1
• /
• pp.1-18
• /
• 2014

Li-air cell is an exotic type of energy storage and conversion device considered to be half battery and half fuel cell. Its successful commercialization highly depends on the timely development of key components. Among these key components, the catalyst (i.e., the core portion of the air electrode) is of critical importance and of the upmost priority. Indeed, it is expected that these catalysts will have a direct and dramatic impact on the Li-air cell's performance by reducing overpotentials, as well as by enhancing the overall capacity and cycle life of Li-air cells. Unfortunately, the technological advancement related to catalysts is sluggish at present. Based on the insights gained from this review, this sluggishness is due to challenges in both the commercialization of the catalyst, and the fundamental studies pertaining to its development. Challenges in the commercialization of the catalyst can be summarized as 1) the identification of superior materials for Li-air cell catalysts, 2) the development of fundamental, material-based assessments for potential catalyst materials, 3) the achievement of a reduction in both cost and time concerning the design of the Li-air cell catalysts. As for the challenges concerning the fundamental studies of Li-air cell catalysts, they are 1) the development of experimental techniques for determining both the nano and micro structure of catalysts, 2) the attainment of both repeatable and verifiable experimental characteristics of catalyst degradation, 3) the development of the predictive capability pertaining to the performance of the catalyst using fundamental material properties. Therefore, under the current circumstances, it is going to be an extremely daunting task to develop appropriate catalysts for the commercialization of Li-air batteries; at least within the foreseeable future. Regardless, nano materials are expected to play a crucial role in this field.

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.299-305
• /
• 2022

Analog-digital converter (ADC) should be one of the most important blocks that convert various physical signals to digital ones for signal processing in the digital signal domain. As most operations of the analog circuit for sensor signal processing have been replaced by digital circuits, high-resolution performance is required for ADC. In addition, low-power must be the critical issue in order to extend the battery time of mobile system. The existing integrating sigma-delta ADCs has a characteristic of high resolution, but due to its low supply voltage condition and advanced technology, circuit error and corresponding resolution degradation of ADC result from the finite gain of the operational amplifier in the integrator. Buffer compensation technique can be applied to minimize gain errors, but there is a disadvantage of additional power dissipation due to the added buffer. In this paper, incremental signal-delta ADC is proposed with buffer switching scheme to minimize current and igh-pass bias circuit to improve the settling time.