• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.49-56
• /
• 1999

This paper present a study on the application of sound pressure and vibration signals to detect the presence of defects in a rolling element bearing using a statistical analysis method. The well established statistical parameters such as the crest factor and the distribution of moments including kurtosis and skewless are utilized in this study. In addition, other statistical parameters derived from the beta distribution function are also used. A comparison study on the performance of the different types of parameter used is also performed. The statistical analysis is used because of its simplicity and quick computation. Under ideal conditions, the statistical method can be used to identify the different types of defect present in the bearing. In addition, the results also reveal that there is no significant advantages in using the beta function parameters when compared to using kurtosis and the crest factor for detecting and identifying defects in rolling element bearings from both sound and vibration signals.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.208-211
• /
• 2001

This paper presents the considerations of the high frequency modulation method for the metal halide lamp electronic ballast. The acousitc resonance phenomenon is occurred, if the metal halide lamp is driven at constant high frequency. The frequency modulation method therefore, is used to avoid the acoustic resonance phenomenon, but the crest factor of lamp current is increased. In this paper, the driving characteristic of the metal halide lamp according to the waveshape and frequency variations of modulating signal is considered with a viewpoint of crest factor.

• Steel and Composite Structures
• /
• v.30 no.6
• /
• pp.577-589
• /
• 2019

In this study, on-site testing was carried out to investigate the vibration performance of a composite steel-bar truss slab with steel girder system. Ambient vibration was performed to capture the primary vibration parameters (natural frequencies, damping ratios, and mode shapes). The composite floor possesses low frequency (< 10 Hz) and damping (< 2%). Based on experimental, theoretical, and numerical analyses on natural frequencies and mode shapes, the boundary condition of SCSC (i.e., two opposite edges simply-supported and the other two edges clamped) is deemed more reasonable for the composite floor. Walking excitations by one person (single excitation), two persons (dual excitation), and three persons (triple excitation) were considered to evaluate the vibration serviceability of the composite floor. The measured acceleration results show a satisfactory vibration perceptibility. For design convenience and safety, a crest factor ${\beta}_{rp}$ describing the ratio of peak acceleration to root-mean-square acceleration induced from the walking excitations is proposed. The comparisons of the modal parameters determined by ambient vibration and walking tests reveal the interaction effect between the human excitation and the composite floor.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12C
• /
• pp.1175-1187
• /
• 2007

This paper proposes a novel crest factor reduction (CFR) algorithm to be deployed on WCDMA basestation. Generally speaking, it is well described that the reduction of peak-to-average ratio (PAR) yields the possibility of using low cost power amplifier such that the basesation becomes economic However, the simple reduction of PAR could degrade the signal quality measured by either peak code domain error (PCDE) or error vector measurement (EVM), and the level of channel interference constrained by adjacent channel leakage ratio (ACLR). Regarding these imperfections, this paper introduces an effective CFR algorithm in which the function of filter-dependent CFR (FDCFR) incorporated with the histogram-based waterfilling code domain compensation (HBWCDC) carries out. To verify the performance of the proposed CFR technique, substantial simulations including comparative works are conducted with obeying W-CDMA basestation verification specification. To exploit the superiority, the performance of the proposed method is tentatively compared with that associated to the simple memoryless clipping method and the memory-required filter-dependent clipping method.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.6
• /
• pp.414-421
• /
• 2011

In determination of the crest height of a vertical structure against attacking of obliquely incident waves, most of existing studies have suggested to use the overtopping reduction factor due to incident angles. However, they have not considered the amplification of wave heights and the spatial distribution of wave overtopping. In this study, a spatial distribution of overtopping due to the amplification of wave heights along a vertical structure is investigated experimentally. It is recommended that the crest height can be determined by the same manner as that for normally incident waves up to 3 significant wave lengths from the one end of the structure. However, the rest part of the structure can be done by employing the overtopping reduction factor with considering the amplification of wave heights and the spatial distribution of wave overtopping.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.6 s.360
• /
• pp.31-39
• /
• 2007

In this paper, a system for real-time or periodic measurement and analysis of RF parameters such as forward transmit power and pilot power in CDMA base station systems is proposed. Such RF characteristic parameter measurement can be prevented from system fault and used to achieve optimal service quality and maximum investment return through cell coverage expansion, subscriber capacity increase and so on. For forward power measurement, the local oscillator frequency for the detector is varied so that the transmit power for all channels can be measured. The channel power measurement can be used to analyze the variation in transmit power for changes in voice traffic. By comparing to forward $E_c/I_o$, the pilot channel power can be deducted, which can be used to determine uy degradation in transmit section modules such as the high dover amplifier. Since an accurate analysis of carefully measured data using the CDMA level detector must be made, the system is designed so that measurement errors due to changes in crest factor with modulation method can be overcome.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.228-232
• /
• 2002

In this paper, In order to solve the problem is proposed using a new type of electronic ballast that the traditional magnetic ballasts operated at 50-60Hz have been suffered from noticeable flicker, high loss, large crest factor and heavy weight which is composed of rectifier, active power corrector, series resonant half bridge inverter, micro-controller and piezoelectric transformer for driving for driving T5 fluorescent lamp were manufactured. The proposed electronic ballast operated at high frequency (about 75kHz) shows a input power factor of more than 0.995, total harmonic distortion of less than $12\%$ and lamp current crest factor of less than 1.5, respectively. Output power and efficiency showed 28w and $85\%$, respectively. Accordingly, it is considered that the ballast using piezoelectric transformer can replace the typical electronic ballast.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2789-2791
• /
• 1999

This paper deals with the design of the HPS electronic ballast, which consists of the ignitor for turning-up and the resonant converter for driving the lamp. Also it contains Power Factor Controller to improve the electronic efficiencies such as power factor, crest factor, low distortion, etc. To make this circuit, it is necessary to simulate it on the computer before we implement it actually. In this paper, we try to modelize the HPS lamp and ballast, and have experiments with 150 watt-HPS lamp from Kwangjunsa.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.585-590
• /
• 2004

Many machine failures are not detected well in advance due to the masking of background noise and attenuation of the source signal through the transmission mediums. Advanced signal processing techniques using adaptive filters and higher order statistics have been attempted to extract the source signal from the measured data at the machine surface. In this paper, blind deconvolution using the eigenvector algorithm (EVA) technique is used to recover a damaged bearing signal using only the measured signal at the machine surface. A damaged bearing signal corrupted by noise with varying signal-to-noise (s/n) was used to determine the effectiveness of the technique in detecting an incipient signal and the optimum choice of filter length. The results show that the technique is effective in detecting the source signal with an s/n ratio as low as 0.21, but requires a relatively large filter length.

• Steel and Composite Structures
• /
• v.21 no.3
• /
• pp.573-588
• /
• 2016

Carbon Fiber Reinforced Plastic (CFRP) and Titanium Alloy (Ti6Al4V) stack, extensively used in aerospace structural components are assembled by fasteners and the holes are made using drilling process. Drilling of stack in one shot is a complicated process due to dissimilarity in the material properties. It is vital to have optimal machining condition and tool geometry for better hole quality and tool life. In this study the tool wear and hole quality were analysed by experimental analysis using three modified twist drills and online tool condition monitoring using Acoustics Emission (AE) sensor. Helix angle and point angle influence tool performance and cutting force. It was found that a tool geometry (TG1) with high helix angle of $35^{\circ}$ with low point angle $130^{\circ}$ results in reduction in thrust force of 150-500 N range but the TG2 also perform almost similar to TG1, but when compared with the AErms voltage generated during drilling it was found that progressive rise in voltage in TG1 is less with respect to TG2 which can be attributed to tool life. In process wear monitoring was done using crest factor as monitoring index. AErms voltage were measured and correlated with the performance of the drills.