• Coupled systems mechanics
• /
• 제12권2호
• /
• pp.183-197
• /
• 2023

Scarce research has been published on crack propagation fracture of flywheels manufactured with carbon fiber-reinforced polymers. The present work deals with a calculation method to determine the conditions for which a crack propagates in the axial direction of the flywheel. The assumptions are: flywheels made with just a single thick ply or ply clustering laminates, oriented following the hoop direction; a single crack is analyzed in the plane defined by the hoop and axial directions; the crack starts close to one of the free edges; its axial length is initially large enough so that its tip is far away from that free edge, and the crack expands the entire circumferential perimeter and keeps its concentric position. The developed method provides information for a good design of flywheels. It is concluded that a fracture-based crack propagation criterion generally occurs at a lower speed than a stress-based criterion. Also, that the evolution of failure with thickness using the fracture criterion is exponential, demonstrating that thin flywheels are relatively not sensitive to crack propagation, whereas thick ones are very prone.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.54-60
• /
• 2001

This study is to investigate the mechanical properties and the fatigue crack propagation of fire resistance steel for frame structure as the chemical composition was changed by addition of N, B and rolled end temperature was varied. We used two kinds of specimen, the one is parallel and the other is perpendicular to the rolling directions. As rolled end temperature increased, volume fraction of ferrite and pearlite decreased, but volume fraction of baintie and grain size increased. Micro-hardness decreased as rolled end temperature increased, but tensile and yield strength increased. Volume fraction of ferrite and pearlite decreased by addition of N. But volume fraction of bainite, tensile and yield strength increased. Microstructure was changed to martensite by addition of B, and tensile and yield strength increased. Fatigue life of TL direction specimen was shorter than that of LT direction specimen. There was no significant effect to fatigue crack propagation rate by addition of N and changing rolling condition, but fatigue life was increased by addition of B.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.916-922
• /
• 1986

본 논문에서는 여러 연구자들이 반타원형 표면균열에 대한 응력확대계수의 수 정계수(correction factor)을 이론해석, 수치해석 및 실험해석 등을 통하여 구했는데, 그 결과는 서로가 5∼100%의 차이를 나타내고 있는 것이다. 이 때문에 표면균열에 대한 연구보고는 다른 분야에 비하여 비교적 적은 편이며, 현재까지 펴면균열의 피로 성장거동에 대한 정열이 설정되어 있지 못한 실정인 것이다. 이에 저자들은 표면균 열의 피로성장거동에 대한 다각적인 연구계획을 추진하고 있는 중이며, 본 보고서는 그 제1단계 연구로서, 초기 표면균열의 크기가 피로균열성장거동에 미치는 영향을 규 명하기 위한 실험적인 연구결과이다.

• 한국전산구조공학회논문집
• /
• 제32권5호
• /
• pp.297-304
• /
• 2019

본 논문에서는 접착영역 모델을 이용하여 2상 리튬이온 충전 시 실리콘 음극 전극의 균열진전 해석을 수행하였다. 리튬화 실리콘은 결정질 실리콘에 비해 부피가 약 3배 이상 크므로 리튬이온 충전 시 외각의 리튬화 실리콘에 매우 큰 압축력이 작용하여 압축항복이 발생한다. 리튬이온 충전 시 외각의 리튬화 실리콘은 압축항복 후에 내부의 결정질 실리콘이 리튬화 실리콘으로 상 변이하면서 발생하는 부피 팽창으로 인해 인장력이 작용한다. 이러한 인장력으로 인해 발생하는 균열진전을 접착영역 모델을 이용하여 모사하였다. 사용한 접착영역 모델은 PPR 포텐셜 기반 접착영역 모델로 하나의 포텐셜을 사용하여 복합모드에 대해서도 에너지 소산에 일관성을 지니고 있다. 유한요소 수치해석 모델로 2상 리튬이온 충전 시 모서리 균열진전을 모사한 결과가 실제 실험결과와 일치함을 확인하였고, 균열 팁에서의 최대 인장응력의 각도를 분석하여 실제 실험처럼 균열진전 방향이 회전할 것을 예측할 수 있었다.

• Smart Structures and Systems
• /
• 제15권6호
• /
• pp.1543-1567
• /
• 2015

In this study, a wireless crack sensor is developed for monitoring cracks propagating in two dimensions. This sensor is developed by incorporating a laser-based optical navigation sensor board (ADNS-9500) into a smart wireless platform (Imote2). To measure crack propagation, the Imote2 sends a signal to the ADNS-9500 to collect a sequence of images reflected from the concrete surface. These acquired images can be processed in the ADNS-9500 directly (the navigation mode) or sent to Imote2 for processing (the frame capture mode). The computed crack displacement can then be transmitted wirelessly to a base station. The design and the construction of this sensor are reported herein followed by some calibration tests on one prototype sensor. Test results show that the sensor can provide sub-millimeter accuracy under sinusoidal and step movement. Also, the two modes of operation offer complementary performance as the navigation mode is more accurate in tracking large amplitude and fast crack movement while the frame capture mode is more accurate for small and slow crack movement. These results illustrate the feasibility of developing such a crack sensor as well as point out directions of further research before its actual implementation.

• 대한토목학회논문집
• /
• 제14권4호
• /
• pp.761-769
• /
• 1994

열차 바퀴의 접촉하중에 의해 레일이 받는 하중형식은 모드 I과 모드 II가 조합된 혼합모드 하중 상태로서 본 연구에서는 레일강의 피로파괴거동을 규명하기 위해 Richard가 개발한 혼합모드 파괴시험편 및 시험 지-그(Jig)를 이용하여 파괴시험을 실시하였으며 그 결과로부터 혼합모드에 대한 용력강도계수의 상관관계를 이용하여 균열성장경로를 평가하고 기제안된 다양한 파괴기준을 비교하였다. 그 결과, 레일강의 균열성장경로는 최대원주응력설과 변형에너지밀도설을 파괴기준은 주변형률설을 따름을 알 수 있었다.

• 콘크리트학회논문집
• /
• 제12권2호
• /
• pp.63-69
• /
• 2000

This study investigates a new method of using a concrete disk to calculate stress intensity factor (SIF) for mixed mode cases. The results indicate that the disk method is more accurate than three point bending test (TPB) in obtaining correct SIF values for mixed mode fracture propagation. Stress intensity factors $K_{I}$ and $K_{II}$ are calculated using a center notched disk subjected to splitting load. The notch angle is calculated by finite element (FEM). Fracture toughness $K_\textsc{k}$ of the concrete is obtained from the load intensities at the initiation of crack propagation. According to the finite element analysis(FEA) and disk test, the results show that mode I and mixed mode cracks propagate toward the directions of crack face and loading point, respectively. The results from FEA with maximum stress theory compare well with the experimental date. Unlike TPB method where an accurate fracture toughness value is difficult to obtain due to the irregular shape of load deflection curve and delayed final crack propagation (following slow stable cracking). fracture toughness value is easily measured in the disk test from the crack initial load. Therefore, it is safe to conclude that disk method is more advantageous than TPB method in analyzing combined mode fracture problems.

• 전산구조공학
• /
• 제9권4호
• /
• pp.189-198
• /
• 1996

콘크리트 중력댐 상부면의 균열에 작용하는 수압의 영향을 주로 고려하여 댐의 파괴거동을 조사하였다. 첫째, 표면적분법에 의하여 응력확대계수를 구하는 경우에 작용하는 수압의 형태를 등분포형태 외에, 삼각형 분포 및 포물선분포도 고려하여 보았다. 둘째, FRANC(FRacture Analysis Code)를 이용하여 균열면에 작용하는 수압의 형태에 따른 기존균열의 전파방향을 추적하였다. 셋째, 월류수위 아래에서 균열이 전파되지 않을 수 있는 한계균열길이를 수압의 분포형태에 따라 구분하여 구하여 보았다. 표면적분법으로 수압의 형태에 따라 응력확대계수를 구한 결과는 FRANC를 이용하여 얻어진 결과와 비교 되었으며 비교적 잘 일치함을 알 수 있었다. 균열면에 작용하는 수압의 형태가 삼각형분포의 경우에 균열의 전파방향은 등분포의 경우에 비하여 댐의 기초쪽으로 기우는 것을 알 수 있었으며, 또한 월류수위 아래에서 한계균열길이는 댐높이의 대략 2/5-1/2되는 곳에서 최대가 됨을 알 수 있었다.

• 한국해양공학회지
• /
• 제7권1호
• /
• pp.124-132
• /
• 1993

In order to examine the effect of anisotropy and stress ratio on fatigue crack propagation rate and opening-closing behavior and also arrest behavior by single tension peak overload, the fatigue tests of constant amplitude atress and single tension peak overload adding to cycle of constant amplitude were carried out in stress ratio of -0.4, -0.2, and 0.4 with materials of T-L and L-T directions in 2024-T3 aluminum alloy plate. Crack opening-closing begavior were measured by the compliance method using COD gage and strain gage. In case of the crack opening-closing behavior was measured by strain gage, the effect of stress ratio is unchangeable. But in the case of COD gage, that is remarkably decreased. Fictitious effective stress intensity factor(U sub(f)) and effective stress intensity factor ratio(U) in L-T direction was higher than those in T-L direction and also threshold arrest overload ratio incrased as stress ratio decreased and that of T-L direction was higher than that in L-T direction.

• Nuclear Engineering and Technology
• /
• 제53권4호
• /
• pp.1250-1258
• /
• 2021

In this paper, the mechanical performance of cracked surface-coated Zircaloy cladding, which has different coating materials, coating thicknesses and initial crack lengths, has been investigated. By analyzing the stress field near the crack tip, the safety zone range of initial crack length has been decided. In order to determine whether the crack can propagate along the radial (r) or axial (z) directions, the energy release rate has been calculated. By comparing the energy release rate with fracture toughness of materials, we can divide the initial crack lengths into three zones: safety zone, discussion zone and danger zone. The results show that Cr is suitable coating material for the cladding with a thin coating while Fe-Cr-Al have a better fracture mechanical performance in the cladding with thick coating. The Si-coated and SiC-coated claddings are suitable for reactors with low power fuel elements. Conclusions in this paper can provide reference and guidance for the cladding design of nuclear fuel elements.