• Journal of Electrical Engineering and Technology
• /
• v.4 no.3
• /
• pp.396-400
• /
• 2009

In this paper, electromagnetic topology (EMT) was used to analyze the electromagnetic compatibility (EMC) of RF circuits including passive and active components. It is difficult to obtain usable results for problems relating to electromagnetic coupling in complex systems when using conventional numerical or experimental methods. Thus it is necessary to find a new methodology for analyzing EMC problems in complicated electromagnetic environments. In order to consider the nonlinear characteristics of active components, a SPICE diode model was used. A power detector circuit and the receiver circuit of a radio control (RC) car were analyzed and experimented in order to verify the validity of this method.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2004.04a
• /
• pp.199-203
• /
• 2004

The azo red pigments for textile printing containing amino-N-substituted benzamide derivatives as diazo components and 2-hydroxy-3-naphthoyl derivatives as coupling components were prepared. They have been printed on cotton, and the fastness, such as light, washing, dry cleaning, rubbing and heat stability was estimated. The new azo red pigments were valuable colorants in case of textile printing.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.813-816
• /
• 1991

Direct-drive SCARA-type industrial robots are increasingly used in the assembly process of small mechanical parts as well as electronic components, which uses direct-drive (DD) motors instead of reduction gear-type conventional motors for the actuators of manipulator arms. There are many advantages in using DD motors for robots, such as no backlash, low friction, high mechanical stiffness capability for fast and precise arm control, and high repeatability of positioning. However, there exist a number of difficulties which must be overcome to ensure proper construction and operation; increasing effects of load veriation and nonlinear and coupling dynamics, severe vibration caused by resonance of the manipulator components and low mechanical damping, etc. In order to handle these difficulties, lots of efforts have been made such as reduction of the arm inertia and elimination of the resonance, Performance evaluation of a recently developed, domestic DD robot shows that it works excellently compared with conventional robots. It, however, requires proved reliability and price competitiveness against its foreign counterparts.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.3
• /
• pp.379-384
• /
• 2008

This paper examines permanent magnet eddy current couplings and brakes. Specifically, the effect of permanent magnet magnetization patterns on the magnetic field and force production is investigated. The eddy current couplings and brakes employ high energy-product neodymium-iron-boron (NdFeB) permanent magnets that act on iron-backed copper drums to provide torque transfer from motor to load without mechanical contact. A 2-dimensional finite element modeling is performed to predict the electromagnetic behavior and the torque-speed characteristics of permanent magnet type eddy current couplings and brakes under constant speed operation.

• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.6
• /
• pp.440-444
• /
• 2016

In this paper, an equivalent circuit model for near-field noise emission is proposed to implement a multimedia operation-monitoring system for mobile devices. The proposed model includes a magnetic field probe that captures noise emissions from multimedia components, and a transfer function for near-field noise coupling from a transmission line source to a magnetic field probe. The proposed model was empirically verified with transfer function measurements of near-field noise emissions from 10 kHz to 500 MHz. With the proposed model, a magnetic field probe was optimally designed for noise measurement on a camera module and an audio codec in a mobile device. It was demonstrated that the probe successfully captured the near-field noise emissions, depending on the operating conditions of the multimedia components, with enhanced sensitivity from a conventional reference probe.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1376-1378
• /
• 1999

Most conventional protection relays are based on processing information in the spectrum that is close to or at power frequency. It is, however, widely known that faults on transmission lines produce frequency components of a wide range In this respect, this paper describes the basis of a Protection technique for transmission lines which utilises high-frequency components. Fault-generated signals caused by post-fault and the signal derived from stack tuner is connected to the coupling capacitor of CVT. Digital signal processing is then applied to the captured information to determine whether the fault is inside or outside the Protected zone, and to discriminate the fault type on transmission line.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.135-136
• /
• 2006

In this paper, isolation strategies for improving broadband circuit performance and preventing noise arising from circuit component coupling are presented. Equivalent circuit parameters, including parasitic elements, are determined for capacitor and inductor structures. The effects of the relative position of the components with regard to a ground plane are considered in the equivalent circuits. Novel meshed ground structures are investigated to determine a configuration that improves the overall circuit performance.

• Journal of Computational Design and Engineering
• /
• v.1 no.1
• /
• pp.55-66
• /
• 2014

A knee joint's longevity depends on the proper integration of structural components in an axial alignment. If just one of the components is abnormally off-axis, the biomechanical system fails, resulting in arthritis. The complexity of various failures in the knee joint has led orthopedic surgeons to select total knee replacement as a primary treatment. In many cases, this means sacrificing much of an other-wise normal joint. Here, we review novel computational approaches to describe knee physiotherapy by introducing a new dimension of foot loading to the knee axis alignment producing an improved functional status of the patient. New physiotherapeutic applications are then possible by aligning foot loading with the functional axis of the knee joint during the treatment of patients with osteoarthritis.

• Korean Journal of Optics and Photonics
• /
• v.12 no.6
• /
• pp.437-445
• /
• 2001

We examine theoretically the properties of the force on Mie particles induced by evanescent fields at a system of multilayer films (including a metal film), at which the surface plasmon resonance is excited by a p-polarized plane electromagnetic wave. An expression of the surface plasmon-coupled evanescent fields produced in Kretschmann (or Sarid) geometry is expanded in terms of vector spherical wave functions, while multiple reflections between the Mie particle and the metal boundary are taken into account. The Cartesian components of the force on Mie particles by the evanescent fields are analytically formulated and numerically evaluated. The force components are increased by one or two orders of magnitude at metal boundaries over those at dielectric boundaries. As a result, we can confirm the possibility of stable manipulation or rotation of a finite-sized object by forces of surface plasmon-coupled evanescent fields.

• Earthquakes and Structures
• /
• v.13 no.1
• /
• pp.9-15
• /
• 2017

In this paper, the influence of the rotational component, about a vertical axis, of earthquake ground motion on the response of building structures subjected to seismic action is considered. The torsional component of ground motion is generated from the records of translational components. Torsional component of ground motion is then, together with translational components, applied in numerical linear dynamic analysis of different reinforced concrete framed structure of three stories buildings. In total, more than 40 numerical models were created and analyzed. The obtained results show clearly the dependence of the effects of the torsional seismic component on structural system and soil properties. Thus, the current approach in seismic codes of accounting for the effects of accidental torsion due to the torsional ground motion, by shifting the center of mass, should be reevaluated.