• 동력기계공학회지
• /
• 제18권6호
• /
• pp.58-63
• /
• 2014

This paper deals with the effects of counterpart materials on the wear behavior of thermally sprayed STS316 coatings. STS316 powders were flame-sprayed onto a carbon steel substrate. Dry sliding wear tests were performed using the applied loads of 15 N. AISI52100, $Al_2O_3$, $ZrO_2$ and $Si_3N_4$ balls were used as counterpart materials. Wear behavior of STS316 coatings against different counterpart materials were studied using a scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS). The results show that the wear behavior of thermally sprayed STS316 coatings strongly depends on the type of counterpart material. Dominant wear mechanism was similar for all studied materials as failure of adhesion film except for Si3N4 used as counterpart material. In the case of Si3N4 used as counterpart material, dominant wear mechanism was abrasion.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1305-1306
• /
• 2006

A new material was developed to achieve improvement of heat durability, improvement of wear resistance, stability of friction coefficient and reduction in aggression to counterpart, because it is difficult to maintain braking properties by using currently available materials in the train wagons used for high-speed transportation. As a result, the new material showed a stable wear resistance even in the speed range of 350km/h, where improvement was also confirmed in reduction of aggression to counterpart material by more than approximately 10%. This development was adopted for the brake lining in the Taiwan High Speed Rail project.

• 동력기계공학회지
• /
• 제13권6호
• /
• pp.123-128
• /
• 2009

The effects of temperature and initial crack length on the impact fracture behavior for the side plate material of FRP ship were investigated. And the effects of the counterpart roughness and sliding distance on the volumetric wear of same material were investigated as well. Impact fracture toughness of GF/PE composites displayed maximum value when the temperature of specimen is room temperature and $50^{\circ}C$, and with decreasing the temperature of specimen, impact fracture toughness decreased. Impact fracture energy of GF/EP composites decreased with increasing the initial crack length of specimen, and this value decreased rapidly when the temperature of specimen is lowest, $-25^{\circ}C$. It is believed that sensitivity of notch on impact fracture energy were increased with decreasing the temperature of specimen. With increasing the sliding distance, the transition sliding distance, which displayed different aspect on the friction coefficient and the volumetric wear loss, were found out. Counterpart roughness had a big influence on the wear rate at running in period, however the effect of counterpart roughness became smaller with sliding speed increase in. Volumetric wear loss were increased with increasing the applied load and the counterpart roughness.

• 소성∙가공
• /
• 제26권6호
• /
• pp.365-371
• /
• 2017

During sling wear of a ferrous metal, a surface layer is formed. Its microstructure, constituting phases, and mechanical property are different from those of the original wearing material. Since wear occurs at the layer, it is important to characterize the layer and understand how wear rate changes with different layers. Various layers are formed depending on external wear conditions such as load, sliding speed, counterpart material, and environmental conditions. In this research, sliding wear tests of pure iron were carried out against two different counterparts (AISI 52100 bearing steel and $Al_2O_3$) in the air and in an inert Ar gas atmosphere. Pure iron was employed to exclude other effects from secondary phases in steel on the wear. Wear tests were performed at room temperature. Worn surfaces, wear debris, and cross-sections were analyzed after the test. It was found that these two different counterparts and environments produced diverse layers, resulting in significant changes in wear rate. Against the bearing steel, pure iron showed higher wear rate in an Ar atmosphere due to severe adhesion than that in the air. On the contrary, the iron showed much higher wear rate in the air against $Al_2O_3$. Different layers and wear rates were analyzed and discussed by oxidation, severe plastic deformation, and adhesion at wearing surfaces.

• 한국전기전자재료학회논문지
• /
• 제20권3호
• /
• pp.228-233
• /
• 2007

Core technologies for integrating hydrogen gas sensor were investigated. In this study, the thermally isolated micro-hot-plate with areas of $100{\times}100-260{\times}260{\mu}m^2$ was fabricated by utilizing surface micromachining technique that provides better manufacturing yield than bulk micromachining counterpart. The optimum design of the sensor was peformed by analyzing the thermal profile of the structure obtained from a ANSYS simulator. The 400-nm-thick polysilicon films doped with phosphorus, the 300-nm-thick aluminum films, and the 200-nm-thick $SnO_2$(or ZnO)films were used as the micro-heater material, the temperature sensor material, and the gas sensitive material, respectively. The experimental results show that the developed gas sensors can detect $H_2$ concentration as low as 1 ppm.

• 대한기계학회논문집B
• /
• 제28권2호
• /
• pp.189-198
• /
• 2004

We consider the problem of whether the three-dimensional checkerboard has the connectivity. For this purpose, we first consider the problem of determining the effective conductivity of a checkerboard-shaped composite material by the Brownian motion simulation method. Specifically, we use the efficient first-passage-time technique. Simulation results show that the effective conductivity of the three-dimensional checkerboard increases faster than the two-dimensional counterpart as the contrast between the phase conductivities increases. This implies that the three-dimensional checkerboard's connectivity is stronger than the two-dimensional checkerboard's and thus each phase material of the three-dimensional checkerboard is more likely to be connected than not to be connected.

• 한국농촌건축학회논문집
• /
• 제11권4호
• /
• pp.25-34
• /
• 2009

The modern philosophy of historic conservation focuses on the permanence of the material aspects of monuments as historic evidence of the artistic achievement of the past. However, so strongly are European attitudes to architecture and its conservation embedded in modern conservation, that it has skewed all conservation thinking towards the concept of the European-type monument which emphasizes visual beauty through its material substance. Thus, some basic ideas of modern conservation seem ill-suited to East Asian architecture which is conceived in a different spirit from its European counterpart. The purposes of the paper are to discuss the need for approaches which are different from the modern Western view of conservation for East Asian architectural heritage, and to make suggestions for developing conservation principles more suited to the unique values and aesthetic sense of East Asian culture and architecture. Conservation principles in the East Asian societies are determined in relation to the spiritual and naturalistic sensibilities of East Asian culture and architecture.

• Bulletin of the Korean Chemical Society
• /
• 제18권6호
• /
• pp.623-628
• /
• 1997

A layered perovskite oxide, $RbLa_2Ti_2NbO_{10}$, was prepared and investigated for proton exchange and intercalation behaviors. Its protonated form, $Hla_2Ti_2NbO_{10}$, exhibits the Bronsted acidity and reacts with organic amines. Polyoxonuclear cation, 4Al_{13}$, was then introduced into the interlayer by refluxing octylamine-intercalated compound with an $Al_{13}$ pillaring solution. These layered oxides were characterized by X-ray diffractometer, thermogravimeter, FT-infrared spectrometer and elemental analyzer. It is observed that the polyoxonuclear cation-pillared material exhibits a bilayer structure and is thermally more stable than organic counterpart at higher temperatures. The surface area of the pillared material annealed at 400 ℃ was the value of 25.1 m²/g.

• Advances in Computational Design
• /
• 제7권4호
• /
• pp.371-393
• /
• 2022

This paper presents a three-dimensional flexible pavement simulated in ANSYS subjected to moving vehicular load on the surface of the pavement typical for the road section in Nepal. The adopted finite element (FE) model of pavement is validated with the classical theoretical formulations for half-space pavement. The validated model is further utilized to understand the damping and dynamic response of the pavement. Transient analysis of the developed FE model is done to understand the time varying response of the pavement under a moving vehicle. The material properties of pavement considered in the analysis is taken from typical road section used in Nepal. The response quantities of pavement with nonlinear viscoelastic asphalt layer are found significantly higher compared to the elastic pavement counterpart. The structural responses of the pavement decrease with increase in the vehicle speed due to less contact time between the tires of the vehicle and the road pavement.

• 대한기계학회논문집A
• /
• 제37권5호
• /
• pp.625-630
• /
• 2013

본 연구는 직경 45 nm인 원통형 나노동공을 가진 산화알루미늄(AAO) 박막에 오일을 함침시켰을때 동점도가 마찰 마멸에 미치는 영향을 규명하고자 실시하였다. 양극산화법으로 제조한 AAO 박막을 직경 1 mm의 440C 스테인리스 강구를 상대재로 하여 왕복동 미끄럼 접촉시험을 실시하였다. 마찰면과 마멸입자는 주사전자현미경과 에닥스(Energy-dispersive X-ray)를 이용해 분석하였다. 높은 동점도 오일의 윤활효과가 저점도 오일에 비해 크게 향상되었다. 동점도가 낮은 경우엔 모든 하중조건에서 심한 마찰흔적과 함께 두꺼운 소성변형층이 넓게 형성되었으며 경계윤활막의 손상으로 접촉면에 물질전이와 화학적 반응 현상이 모두 발생하였다. 오일의 점도가 높은 경우 마찰면에 존재하는 경계윤활막이 파괴되지 않아 마찰흔적과 소성변형층의 형성이 매우 적었으며 물질전이와 화학적 반응이 방지되었다.