• Current Optics and Photonics
• /
• 제5권3호
• /
• pp.289-297
• /
• 2021

We describe a comb-mode resolving spectroscopic technique by direct time-domain phase correction of unstable interferograms obtained from loosely locked two femtosecond lasers. A low-cost continuous wave laser and conventional repetition rate stabilization method were exploited for locking carrier and envelope phase of interferograms, respectively. We intentionally set the servo control at low bandwidth, resulting in severe interferograms' fluctuation to demonstrate the capability of the proposed correction method. The envelope phase of each interferogram was estimated by a quadratic fit of carrier peaks to correct timing fluctuation of interferograms in the time domain. After envelope phase correction on individual interferograms, we successfully demonstrated 1 Hz linewidth of RF comb-mode over 200 GHz optical spectral-bandwidth with 10-times signal-to-noise ratio (SNR) enhancement compared to the spectrum without correction. Besides, the group delay difference between two femtosecond pulses is successfully estimated through a linear slope of phase information.

• 한국정보통신학회논문지
• /
• 제26권11호
• /
• pp.1747-1750
• /
• 2022

As shrinking the semiconductor process into the deep sub-micron to achieve high-density, low power and high performance integrated circuits, MBU (multiple bit upset) by soft errors is one of the major challenge of on-chip memory systems. To address the MBU, single error correction, double error detection and double adjacent error correction (SEC-DED-DAEC) codes have been recently proposed. But these codes do not resolve mis-correction. We propose the SEC-DED-DAEC-TAED(triple adjacent error detection) code without mis-corrections. The generated H-matrix by the proposed heuristic algorithm to accomplish the proposed code is implemented as hardware and verified. The results show that there is no mis-correction in the proposed codes and the 2-stage pipelined decoder can be employed on-chip memory system.

• 한국생산제조학회지
• /
• 제24권1호
• /
• pp.130-134
• /
• 2015

The automobile industry is ubiquitous and involved in the handling of metal, machines, electricity, electron, and chemistry including the products of many types of processes. In the process of installing engines as a part of the car assembly line, the measurement and correction of the position of the stud bolts consumes a great deal of time. Additionally, defective parts must be manually removed. In the process of engine installation, the speed of the operation, related to the economics of vehicle assembly, is dependent upon measuring the precise position of the stud bolt, reducing the length of correction time, and increasing the working rate. This paper deals with securing the economic feasibility of the manufacturing process, increasing the safety by removing risk factors in the working area, and improving and equalizing the quality by developing an automatic system for the process involving a stud bolt.

• 한국멀티미디어학회논문지
• /
• 제24권2호
• /
• pp.285-294
• /
• 2021

This study developed a responsive healthcare system that users can easily use in real life to prevent turtle neck syndrome by posture correction. We propose a system that naturally induces direct posture improvement by adjusting the height with a responsive cradle through a turtle neck discrimination algorithm detecting the turtle neck posture in real time using a webcam. The turtle neck algorithm was developed based on machine learning, using the points that the distance relationship between the jaw line and the shoulder varies depending on the posture. For the younger age group, which is particularly problematic due to the increase in the use of IT devices, image data in different situations according to the height and posture of the cradle was collected and learned as a support vector machine classifier. In addition, a height-adjustable cradle that can support a laptop has been created and expanded into a responsive cradle that can be controlled with software by interlocking with the Arduino. Therefore, this service enables posture correction of many modern people suffering from turtle neck syndrome and will become an essential platform in the increasing online environment in the non-contact era.

• 디지털산업정보학회논문지
• /
• 제10권4호
• /
• pp.63-70
• /
• 2014

Method a target estimation in spatial are mobile wireless communication using network cell and GPS. It have much error that mobile wireless communication depend on cell size. GPS method can't find a target in shadow and inner area. In this paper, we estimate a target as direction of arrival method using adaptive array antenna system. Adaptive array antenna system can obtain desired signal to remove other signal This paper studied digital beamforming method in order to estimation a target. Proposed method is modified optimum weight and antenna error correction to estimation an optimal receive signal. Digital beamforming method decided a signal phase and amplitude from received signal on array antenna element. But if it is not to do error correction of received signal, system performance have decreased. Firstly, we proposed modified optimum weight in order to finding desired target. Secondly, we are error correction of antenna incident signals by optimal weight before digital beamforming method. Thirdly, throughly simulation, we showed that system performance of proposed method compare proposal method with general method. It have improved resolution of estimation target to good performance more proposed method than general method.

• 동력기계공학회지
• /
• 제15권4호
• /
• pp.25-30
• /
• 2011

This study is made to provide with a method for correcting the geometric distortion of the digital radiography image by analytical approach based upon the inverse square law and Beer's law. This study is aimed to find out and improve a mathematic model of nonlinear type. Variations in the alignment of the X-ray source, the object, and imaging plate affect digital radiography images. A model which is expressed in parameter values; e.g, angle, position, absorption coefficient, length, width and pixel account of radiography source, is developed so as to match the sample image. For the best correction of the digital image that is the most similar to the model image, a correction technique based upon tangent is developed; then applied to the digital radiography images of steel tubes. As a result, the image correction is confirmed to be made successfully.

• 제어로봇시스템학회논문지
• /
• 제15권8호
• /
• pp.772-777
• /
• 2009

The geometric distortion of image is one of the most important parameters that take effect on the accuracy of optical inspection systems. We propose a new correction method of the image distortion to increase the accuracy of PCB inspection systems. The model-free method is applied to correct the randomly distorted image that cannot be represented by mathematical model. To reduce the correction time of inspection system, we newly propose a grid reduction algorithm that minimize the number of grids by the quad-tree approach. We apply the proposed method to a PCB inspection system, and verify its usefulness through experiments using actual inspection images.

• 한국컴퓨터정보학회논문지
• /
• 제22권10호
• /
• pp.19-26
• /
• 2017

In this paper, we propose an efficient image equipment implementation for the detector characteristics of various detectors by analyzing un-cooled thermal detector that exhibits nonlinear changes due to external temperature effects. First, we explain Thermal Electric Cooler for un-cooled detector temperature control system and Non-image correction methode for IR system. Second, we present the results of a study on an efficient control technique that can minimize the deterioration of image quality by controlling a un-cooled thermal detector without a thermal electric cooler(TEC) inside. Third, we suggest Image Correction Methods for Uncooled IR TECless Detector with Non-linear characteristics due to Temperature Change. So, we analyze and present the results of Image correction methods for various un-cooled thermal detector.

• Journal of Communications and Networks
• /
• 제16권3호
• /
• pp.322-334
• /
• 2014

Multimedia content is very sensitive to packet loss and therefore multimedia streams are typically protected against packet loss, either by supporting retransmission requests or by adding redundant forward error correction (FEC) data. However, the redundant FEC information introduces significant additional bandwidth requirements, as compared to the bitrate of the original video stream. Especially on wireless and mobile networks, bandwidth availability is limited and variable. In this article, an adaptive FEC (A-FEC) system is presented whereby the redundancy rate is dynamically adjusted to the packet loss, based on feedback messages from the client. We present a statistical model of our A-FEC system and validate the proposed system under different packet loss conditions and loss probabilities. The experimental results show that 57-95%bandwidth gain can be achieved compared with a static FEC approach.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.302-302
• /
• 2000

This paper presents the measurement and correction of PCB alignment errors for PCB-manufacturing machines. The conventional PCB-manufacturing machine doesn't have enough accuracy to accommodate the demand for high-resolution circuit pattern and high-density mounting capacity of electronic chips. It is because of alignment errors of PCB loaded to the PCB-manufacturing machine. Therefore, this study focuses on the development of the system which is able to measure and correct alignment errors whit high-accuracy. An automatic optical inspection part measures the PCB alignment error using two cameras, and the high-accuracy 3-axis stage makes correct of these error. The operating system is run in the environment of Window 98 (or NT). Finally we implemented this system to PCB screen printer and PCB exposure system.