• Steel and Composite Structures
• /
• v.49 no.3
• /
• pp.271-280
• /
• 2023

In this study, the three-dimensional finite element method is used to analyze the behavior of corner cracks in finite-thickness plates repaired with a composite patch. The normalized stress intensity factor at the crack front is used as fracture criterion. Comparison of stress intensity factor values at the internal and external positions of repaired quarter-elliptical corner crack was done, for three repair techniques. The influence of mechanical and geometrical properties of the adhesive layer and the composite patch on the variation of the stress intensity factor (SIF) at the crack-front was highlighted. The obtained results show that the application of double patch leads to a remarkable reduction of SIF at the crack front, compared to facial and lateral repairs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1159-1165
• /
• 2008

In this paper, a single-feed equilateral-triangular microstrip antenna with truncated corners is used for achieving diverse radiation polarization. The proposed antenna is excited by a microstrip line, which is place parallel to an oblique side of the equilateral-triangular patch. Depending on whether the three identically-sized comers of the triangular patch are cut or not, the equilateral-triangular microstrip antenna shows linear polarization(LP) or left-hand circular polarization(LHCP) or Tight-hand circular polarization(RHCP). Based on the equilateral-triangular microstrip antenna with truncated corners, a novel reconfigurable microstrip antenna with switchable polarization sense is also proposed. The proposed reconfigurable antenna has a simple structure, consisting of a corner-truncated triangular patch, a small triangular conductor, and a microstrip line. Using a biased PIN diode between the patch and the small triangular conductor, it can produce LP or RHCP according to bias voltages. From the measured results, low cross polarization level when operated in the linear state and good axial ratio in the circular state are observed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.480-481
• /
• 2015

General microstrip patch antenna has small bandwidth. If corner of a patch antenna is properly cutted to be triangular shape, then input impedance of patch antenna should be varied. Using this characteristic wideband patch antenna can be implemented. In this paper, wideband microstrip patch antenna operating in 2.4GHz ISM band is investigated through tracking variation of input impedance corresponding to cutting shape of patch antenna.

• Journal of electromagnetic engineering and science
• /
• v.18 no.4
• /
• pp.215-220
• /
• 2018

This study presents a dual-band polarization-reconfigurable antenna that comprises a large square patch with a pair of corner-cut edges and two small square patches with a shorting via. Two PIN diodes are located between the large square patch and two small square patches. Depending on the bias state applied to the two PIN diodes, each small patch may be disconnected or connected to the large square patch. As a result, the proposed antenna can provide polarization reconfigurability between two orthogonal linear polarizations. Further, the proposed antenna operates at 2.51 GHz and 2.71 GHz. From the measured results, the proposed antenna shows a 10 dB bandwidth of 2.39% (2.49-2.55 GHz) and 2.58% (2.68-2.75 GHz). In this work, the frequency ratio can be easily controlled by changing the size of the small patch.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.312-318
• /
• 2010

A small reconfigurable patch antenna is proposed to achieve polarization diversity for digital multimedia broadcasting systems at 2.6 GHz. To obtain polarization diversity, a pair of on-slit PIN diodes is inserted in each diagonal of a cross-shaped patch. Thus, four PIN-diodes on these slits are utilized to change the connection of the slits and thus achieve polarization. Bias circuits for the diodes are allocated in the cutting corner of the cross-shaped patch to minimize the antenna size. The antenna produces left-hand circular polarization, right-hand circular polarization, or linear polarization, depending on the PIN-diode status. Analysis of circular polarization operation is explicated. Measurements show a gain of about 1.5 dB, a cross polarization of about -20 dB, and an axial ratio of about 2.5 dB.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.235-240
• /
• 2005

This paper presents a dual band circularly polarized microstrip patch antenna. The antenna consists of two corner truncated patches implemented in one plane and single feed point. The input signal is directly excited to the patch 2 and the patch 1 is fed from patch 2 by coupling between two patches. The antenna is operated at 900 MHz and 2.45 GHz bands and has the right hand circularly polarized radiation pattern at all. The measured gains of the antenna are 2.95 dBic at 900 MHz band and 4.6 dBic at 2.45 GHz band.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3880-3884
• /
• 2010

In this paper, circularly polarized micro-strip GPS antenna has been designed and fabricated. In order to improve of frequency properties, patch size, corner truncated size and feed positions were simulated using HFSS simulation program. Micro-strip GPS antenna was fabricated on the FR4 substrate of dielectric constant 4.4. The fabricated GPS antenna has that center frequency is 1.575GHz and insertion loss is -34.50dB.

• ETRI Journal
• /
• v.30 no.5
• /
• pp.718-722
• /
• 2008

In this paper, a design for a novel microstrip antenna with circular polarization diversity is proposed and experimentally investigated. This antenna is excited by a microstrip line, which is located at the corner of a circular patch. The polarization state can be switched electrically by setting a diode to on or off. The novel structure we describe here enables the optimization of the input match for both polarizations. From the measured result, good axial ratios are observed at the operating frequencies.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.6
• /
• pp.563-567
• /
• 2010

In this paper, circularly polarized micro-strip GPS of 1.57 GHz and DMB of 2.63~2.65GHz antenna have been studied. In order to improve of frequency properties, parameters such as patch size, corner truncated type, and feed positions were simulated using HFSS program. GPS and DMB antenna were fabricated and characteristics were measured using network analyzer.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.1
• /
• pp.127-135
• /
• 2009

This paper presents a new technique for corner shape based object retrieval from a database. The proposed feature matrix consists of values obtained through a neighborhood operation of detected corners. This results in a significant small size feature matrix compared to the algorithms using color features and thus is computationally very efficient. The corners have been extracted by finding the intersections of the detected lines found using Hough transform. As the affine transformations preserve the co-linearity of points on a line and their intersection properties, the resulting corner features for image retrieval are robust to affine transformations. Furthermore, the corner features are invariant to noise. It is considered that the proposed algorithm will produce good results in combination with other algorithms in a way of incremental verification for similarity.