• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.63-70
• /
• 2002

In tunnel construction, the information on the rock quality and the location of fault or fracture are crucial for economical design of support pattern and for safe construction of the tunnel. The grade of rock is commonly estimated through the observation with the naked eye of recovered cores in drilling or from physical parameters obtained by their laboratory test. Since drilling cost is quite expensive and terrains of planned sites for tunnel construction are rough in many cases, however, only limited information could be provided by core drilling Electrical resistivity and EM surveys may be a clue to get over this difficulty. Thus we have investigated electrical resistivity and EM field data providing regional Information of the rock Quality and delineating fault and fracture over a rough terrain. In this paper, we present some case histories using electrical resistivity and EM survey for the site investigation of tunnel construction. Through electrical resistivity and EM survey, the range and depth of coal seam was clearly estimated, cavities were detected in limestone area, and weak zones such as joint, fault and fracture have been delineated.

• 한국기계가공학회지
• /
• 제10권1호
• /
• pp.73-79
• /
• 2011

In this study, coring with diamond core drill on the sintered $Al_2O_3$ ceramic plate were carried out with different coring conditions such as various cutting speed and feed rate to evaluate their effectiveness on the wearing behavior of diamond tool and coring quality. The wearing rate of diamond core drill were getting better with increasing cutting speed and feed rate but the quality of cored hole were getting worse as increasing cutting speed and feed rate.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 추계학술대회
• /
• pp.245-248
• /
• 1997

Operative interventions for the management of osteonecrosis of the femoral head (ONFH) include core drilling, with or without vascularized fibular bone grafting. Nevertheless, their clinical results have not been consistently satisfactory. Recently, a new surgical procedure that incorporates cementation with polymethylmethacrylate (PMMA) after core drilling has been tried clinically. In this study, a biomechanical analysis using a finite element method(FEM) was undertaken to evaluate surgical methods and their underlying surgical parameter. Our finite element models included five types. They were (1) normal model (Type I), (2) necrotic model (Type II), (3) core decompressed model (Type III). (4) fibular bone grafted model (Type IV), and (5) cemented with PMMA model (Type V). The geometric dimensions of the femur were based on digitized CT-scan data of a normal person. Various physiological loading conditions and surgical penetration depths by the core were used as mechanical variables to study their biomechanical contributions in stress transfer within the femoral head region. In addition. the peak von Mises stress(PVMS) within the necrotic cancellous bone of the femoral head was obtained. The fibular bone grafted method and cementation method provided optimal stress transfer behaviors. Here. substantial increase in the low stress level was observed when the penetration depth was extended to 0mm and 5mm from the subchondral region. Moreover, significant decrease in PVMS due to surgery was observed in the fibular bone grafted method and the cementation method when the penetration depths were extended up to 0 and 5mm from the subchondral region. The drop in PVMS was greater during toe-off than during heel-strike (57% vs. 28% in Type IV and 49% vs. 22% in Type V). Both the vascularized fibular bone grafting method (Type IV) and the new PMMA technique (Type V) appear to be very effective in providing good stress transfer and reducing the peak Von-Mises stress within the necrotic region. Overall results show that fibular bone grafting and cementation methods are quite similar. In light of above results, the new cementation method appears to be a promising surgical alternative or the treatment of ONFH. The use of PMMA for the core can be less prone to surgical complication as opposed to preparation of fibular bone graft and can achieve more immediate fixation between the core and the surrounding region.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 가을 학술발표회 논문집
• /
• pp.39-44
• /
• 2002

A three node triangular element with drilling rotations incorporating Improved Layerwise Zig-zag Theory(HZZT) is developed to analyze the vibration of spinning pretwisted composite blades with embedded damping layer. Matching conditions at the interfaces between the damping material and the border material are enforced by setting the shear forces matched and different shear strains along the interfaces. The natural frequencies and modal loss factors of cantilevered pretwisted composite blade with damping core are calculated with the present triangular element enforcing the matching conditions and compared to experimental results and MSC/NASTRAN results using a layered combination of plate and solid elements.

• 한국암석학회:학술대회논문집
• /
• 한국암석회.한국광물학회 2009년도 공동학술발표회 논문집
• /
• pp.136-136
• /
• 2009

• 터널과지하공간
• /
• 제2권2호
• /
• pp.251-264
• /
• 1992

In this study, the size effect in measuring the fracture toughness of rock was investigated using the ISRM Suggested Method for Fracture toughness using Chevron Bend Specimens. Total 58 specimens were prepared with 4 different diameters, 29, 42, 54, 68mm and center cut-chevron notch. In addition to this, to evaluated the effect of anisotropy of Jecheon granite, which is the sample for this study, core drilling direction was adjusted perpendicular(short transverse) and parallel(arrester) to the rift plane in the sample and the measured fracture toughness for each direction were compared. Important results obtained from this study are as follows. Level ll test condition is more adequate than l, because of low data scattering and precision and corrected fracture toughness of Jechoen granite measured and 2.2MPa{{{{ SQRT { m} }}}} for arrester direction with minimum initial crack length 0.7cm. From the relationship between core diameter and initial crack length presented in the ISRM testing method, the specimen diameter should be bigger than 47mm. The fracture toughnesses measured for arrester and short transverse directon show 10% difference. This is to the anisotropy of Jecheon granite possessing rift plane.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.279-280
• /
• 2009

본 연구는 장기간(공용년수 31년) 해안환경에 노출된 해안구조물의 염해에 대한 내구성 분석을 목적으로 하였다. 실험을 위해 총 6 개의 Core를 사용하였다. 각 Core내의 콘크리트 총염화물을 1.5cm간격으로 측정하고 실험결과를 바탕으로 철근의 부식 계시시기를 예측하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.104-106
• /
• 2001

In this paper, it is object of design of high efficiency slotless BLDC motor using film coil. Slotless BLDC motor is able to have high efficiency property and low cogging torque, due to magnetization of stator core have constant contribution by slotless core. But it is difficult to make coil winding of slotless BLDC motor. So we make amateur of slotless BLDC motor using film coil. Film coil is fabricated by drilling, electro-plating and etching of copper/insulator/copper plate. In this paper, after design of slotless BLDC motor for moving axial blower, it is fabricated by NdFeB permanent magnet type rotor and film coil.

• 한국지형학회지
• /
• 제26권2호
• /
• pp.39-54
• /
• 2019

In this paper, based on evidence of coastal sediment, we show that erosion and sedimentation environments are very sensitive to sea level changes during the Medieval Warm Period (MWP) and the Little Ice Age (LIA). We identified four sedimentary units(4.57-3.07m), which formed in the Dark Age Cool Period (DACP), MWP and LIA were classified based on the lithostratigraphy, grain size distribution, magnetic susceptibility and geochemistry of a drilling core taken from the west coast of Hwaseong City. The unconformity surfaces as boundaries of the units were also identified by the lithostratigraphy shown on the drilling core. We propoese that sedimentation was dominant in the area during the periods of sea level rise, whereas erosion prevailed during the periods of sea level fall. Particularly, extreme events, such as floods and typhoons are believed to have accelerated these processes, and we found the associated evidence in sediments of two units. This study provides an example of estimating the relative sea level variation using coastal sediments and may be useful for studying past sea level changes around the Korean Peninsula.

• 한국분말재료학회지
• /
• 제15권5호
• /
• pp.378-385
• /
• 2008

This article presents the successful consolidation of the mixed Co and Diamond powders for a drilling segment by the combined application of magnetic pulsed compaction (MPC) and subsequent sintering, and their properties were analyzed. Homogeneous hardness (Hv 220) and density (97%) of sintered bulks fabricated by MPC were obtained by the new technique, where higher pressure has been employed for short period of time than that of general process. A fine microstructure and homogeneous hardness in the consolidated bulk were observed without cracks. Relatively higher drilling speed of 9.61 cm/min and life time of 6.55 m were found to the MPCed specimens, whereas the value of the specimens fabricated by general process was 11.71 cm/min and 7.96 m, respectively. A substantial improvement of mechanical properties of segment was achieved through this study.