• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.1264-1272
• /
• 2015

This study was performed to compare the perceived importance and performance frequency of the core nursing skills between general and special department. Subjects were 182 nurses who work on the hospital. Data was collected using items made by Korean accreditation board of nursing education and analyzed by frequency, mean and t-test. There were differences of importance and frequencies about nursing core skill between general and special wards. Core nursing skills of general wards were higher importance on intradermal injection(p=.011), transfusion(p=.028), simple catheterization(p=.047), cleansing enema(p=<.001), preoperative and postoperative care(p=.035), management administration(p=.027) and oxygenation with cannular(p=.002) than special wards. Actual performance frequency core nursing skills of general wards were higher similar on transfusion(p=.002), intermittent tube feeding(p=.032), simple catheterization(p=<.001), cleansing enema(p=<.001), preoperative care(p=.001), postoperative care(p=<.001), management administration(p=.001), protection equipment for quarantine room and waste disposal(p=.021), oxygenation with cannular(p=<.001) than special wards. It is needed to develop efficient and sequential program to learning the nursing core skills for nursing students.

• Economic and Environmental Geology
• /
• v.46 no.4
• /
• pp.279-289
• /
• 2013

The most critical factor in developing coalbed methane(CBM) reservoir is absolute permeability. Both productivity and economics of the CBM depend on the absolute permeability. The methods to estimate it are core analysis and well test. However, absolute permeability determined by core analysis cannot be a good representative of CBM reservoir. Therefore, it is generally estimated by well test. In this study, well test methods applicable of CBM reservoir were classified with their characteristics. Merits and demerits of each well tests were also analyzed. Based on those parameters, design considerations and procedures of well test were derived. After each well tests was performed, the procedure of well test interpretations to estimate reservoir properties such as absolute permeability and skin factor was presented.

• Nuclear Engineering and Technology
• /
• v.49 no.7
• /
• pp.1537-1546
• /
• 2017

Many thermal-hydraulic tests have been conducted at the Korea Atomic Energy Research Institute for verification of the SMART (System-integrated Modular Advanced ReacTor) design, the standard design approval of which was issued by the Korean regulatory body. In this paper, the contributions of these tests to the standard design approval of SMART are discussed. First, an integral effect test facility named VISTA-ITL (Experimental Verification by Integral Simulation of Transients and Accidents-Integral Test Loop) has been utilized to assess the TASS/SMR-S (Transient and Set-point Simulation/Small and Medium) safety analysis code and confirm its conservatism, to support standard design approval, and to construct a database for the SMART design optimization. In addition, many separate effect tests have been performed. The reactor internal flow test has been conducted using the SCOP (SMART COre flow distribution and Pressure drop test) facility to evaluate the reactor internal flow and pressure distributions. An ECC (Emergency Core Coolant) performance test has been carried out using the SWAT (SMART ECC Water Asymmetric Two-phase choking test) facility to evaluate the safety injection performance and to validate the thermal-hydraulic model used in the safety analysis code. The Freon CHF (Critical Heat Flux) test has been performed using the FTHEL (Freon Thermal Hydraulic Experimental Loop) facility to construct a database from the $5{\times}5$ rod bundle Freon CHF tests and to evaluate the DNBR (Departure from Nucleate Boiling Ratio) model in the safety analysis and core design codes. These test results were used for standard design approval of SMART to verify its design bases, design tools, and analysis methodology.

• Nuclear Engineering and Technology
• /
• v.25 no.2
• /
• pp.204-214
• /
• 1993

Work on fracture mechanics has provided a technical basis for elimination of main coolant loop double ended guillotine breaks from the structural design basis of reactor coolant system. Without main coolant loop pipe breaks, the tributary pipe breaks must be considered as design bases until further fracture mechanics work could eliminate some of these breaks from design consideration. This paper determines the core support barrel shell responses for the 3 inch pressurizer spray line nozzle break which is expected to be the only inlet break remaining in the primary side after leak-before-break evaluation is extended to smaller size pipes in the near future. The responses are compared with those due to 14 inch safety injection nozzle break and main coolant loop pipe break. The results show that, when the leak-before-break concept is applied to the primary side piping systems with a diameter of 10 inches or over, the core support barrel shell responses due to pipe breaks in the primary side are negligible for the faulted condition design.

• The Journal of Engineering Geology
• /
• v.11 no.3
• /
• pp.279-294
• /
• 2001

When constructing subsurface structures and drilling wells, the precise hydraulic parameters must be obtained for operating safety and for developing enough quantity of groundwater, respectively. In this study we conducted water injection test at different depths on six boreholes drilled in the granite of Mt. Geumjeong. Hydraulic conductivity was calculated using Moye and Hvorslev methods. The relation between hydraulic conductivity and fracture frequency data obtained from acoustic televiewer and core log was analyzed. From the result, though the correlation coefficient between the hydraulic conductivity and the fracture frequency from acoustic televiewer data is higher than that between the hydraulic conductivity and the fracture frequency from core log data on most of the test holes, the correlation coefficient between the hydraulic conductivity and the fracture frequency from the televiewer data is lower than 0.5. This suggests that the hydraulic conductivity of granite in the study area is influenced not only by the fracture frequency but also by various factors of fracture network such as fracture aperture and length, interconnectivity of fractures, fracture orientation and angle, filling material and so on.

• Journal of the Korean Institute of Gas
• /
• v.22 no.5
• /
• pp.53-61
• /
• 2018

Low-salinity water based polymerflooding (LSPF) is one of promising enhanced oil recovery (EOR) method that has the synergetic effect of combining polymer injection method and low-salinity water injection method. In order to maximize EOR efficiency, it is essential to design low-salinity water appropriately considering the properties of polymer. In this aspect, the main purpose of this study is to investigate the effect of pH and $SO_4{^{2-}}$ ion which one of PDI (Potential Determining Ion) on oil production when applying LSPF to carbonate oil reservoir. First, the stability and adsorption of polymer molecule were analyzed in different pH of injection water and $SO_4{^{2-}}$ concentration in injection water. As a result, regardless of pH and $SO_4{^{2-}}$ concentration, when $SO_4{^{2-}}$ ion was contained in injection water, the stability of polymer solution was obtained. However, from the result of polymer retention analysis, in neutral state of injection water, since $SO_4{^{2-}}$ interfered the adsorption of polymer, the adsorption thickness of polymer was thinner as $SO_4{^{2-}}$ concentration was higher. On the other hand, when injection water was acidic as pH 4, the amount of polymer adsorption increased with the injection of polymer solution, so the mobility of polymer solution was greatly lowered. From the results of wettability alteration due to low-salinity water effect, in the case of neutral injection water injected, as $SO_4{^{2-}}$ concentration was increased, more oil which attached on rock surface was detached, altering wettability from oil-wet to water-wet. On the other hand, in acidic condition, due to complex effect of rock dissolution and polymer adsorption, wettability of the entire core system was less altered relatively to neutral condition. Therefore, it was evaluated that better EOR efficiency was obtained when injecting low-salinity water based polymer solution containing high concentration of $SO_4{^{2-}}$ with neutral condition, enhancing the oil production up to 12.3% compared to low-salinity water injection method.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.441-448
• /
• 2000

While the Grouting has been used to reinforce the foundation of structures in wide range of application, there need complementary measures against problems such as pollution, durability, influence on the adjacent structures. Compaction Grouting, the injection of a very stiff, 'zero-slump' mortar grout under relatively high pressure, displaces and compacts soils. It can effectively repair natural or man-made soil strength deficiencies in variety of soil formations. In this paper, on the basis of the case history constructed in this year, a study has been performed to analyze the basic mechanism of the Compaction Grouting, Also, the effectiveness of the ground improvement and the bearing capacity of the Compaction Pile has been verified by the S.P.T and core strength.

• Design & Manufacturing
• /
• v.2 no.6
• /
• pp.38-42
• /
• 2008

Recently, the demands of digital camera and miniature camera module for mobile-phone is increased significantly. Lenses which is the core component of optical products are made by the injection molding(plastic lens) or GMP(glass lens). Plastic lens is not enough to improve the resolution and performance of optic parts. Therefore, the requirement of glass lens is increased because it is possible to ensure the high performance and resolution. In this paper, the thermal stress analysis of 3 cavity GMP mold for molding glass lens was performed for estimating the thermal stress and amount of deformation. Finally, the modification plan based on the analysis results was deducted.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.1
• /
• pp.118-125
• /
• 2003

As consumer's desire becomes various, agility of mold manufacturing is the most important factor for competitive mold manufacturer. Decision making process is required to produce optimal result of CAM systems in using commercial CAM system to generate tool path. The paper proposes a methodology fur computer-assisted tool selection procedures for various cutting type of rough, semi-rough and finish cuts. The procedure provides assistance for machining tool selection by analyzing sliced CAD model section of die cavity and core. Information about machining time for the generated NC-code is used to aid the tool selection. The module is developed with commercial CAM API. This module will be used fur the optimization of tool selection and planning process.

• Design & Manufacturing
• /
• v.8 no.2
• /
• pp.50-55
• /
• 2014

Recently, semi-stack mold have been developed for satisfying the various elements required in the mold industry. The mold is possible using with general-purpose injection molding machine by weight reduction through the improvement of the mold structure. In order to do that, tension core, spiral cooling system and half runner system were applied. It is effective for increased productivity and decreased of loss to the materials. However, the mold is required the filling balance in order to improve the quality and efficiency. Thus this study performed that optimum design and analysis of semi-stack mold for filling balance.