• Journal of the Korean Ceramic Society
• /
• v.34 no.9
• /
• pp.986-992
• /
• 1997

Cordierite ceramic was prepared by sol-gel method. It was analyzed by Infrared spectroscopy and X-ray diffraction patterns that the ceramic was chemically mixed in molecular level and transformed to $\alpha$-cordierite at 125$0^{\circ}C$. Water vapour treatments for aging and drying process were conducted to get porous cordierite with thermally stable pore structure. It resulted in 220-410 $m^2$/g BET surface area and mesoporous structure with mean pore diameter, 40$\AA$. Compared to naturally dried ceramic, the ceramic showed superior thermal stability of surface area up to $700^{\circ}C$. Surfaces of porous cordierite ceramics were observed by SEM.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1009-1010
• /
• 2006

In this study, we attempt to synthesize the cordierite from the reaction of fly-ash, alumina, silicon dioxide, and magnesia powders. For the purpose of air purification, the honeycomb filter with porous cordierite was fabricated from the combination of synthetic cordierite and pore forming agent. Fabricated porous cordierite honeycomb was prepared with high porosity (58%), and good compressive strength (69MPa).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6106-6113
• /
• 2013

Automotive three-way catalyst substrate has a cordierite ceramic honeycomb structure. The substrate in the high engine speed range doesn't satisfy the design fatigue life due to the low mechanical properties of cordierite ceramic. SiC ceramic has higher mechanical properties than cordierite ceramic. If the automotive three-way catalyst substrate is made from the SiC ceramic honeycomb structure, the substrate can be prevented from premature failure. In this study, the mechanical properties of SiC ceramic honeycomb substrate were estimated by FEA. The FEA results indicated that the MOR and elastic modulus for the SiC ceramic honeycomb substrate was much higher than those for the cordierite ceramic honeycomb substrate.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.719-724
• /
• 2018

Cordierite composed of an alumina-silica-magnesia compound has a low coefficient of thermal expansion(CTE) and excellent thermal shock resistance. It also has a low dielectric constant and high electrical insulation. However, due to low mechanical strength, it is limited for use in a ceramic heater. In this study, $ZrO_2$ is added to an 80 wt% cordierite-20 wt% mullite composition, and the effect of $ZrO_2$ addition on the mechanical strength and thermal shock resistance is investigated. With an increasing addition of $ZrO_2$, cordierite-mullite formed $ZrO_2$, $ZrSiO_4$ and spinel phases. With sintering conducted at $1400^{\circ}C$ with the addition of 5 wt% $ZrO_2$ to 80 wt% cordierite-20 wt% mullite, the most dense microstructure forms along with an excellent mechanical strength with a 3-point flexural strength of 238MPa. When this composition is quenched in water at ${\Delta}T=400^{\circ}C$, the 3-point flexural strength is maintained. Moreover, when this composition is cooled from $800^{\circ}C$ to air, the 3-point flexural strength is maintained even after 100 cycles. In addition, the CTE is measured as $3.00{\times}10^{-6}{\cdot}K^{-1}$ at $1000^{\circ}C$. Therefore, 80 wt% cordierite-20 wt% mullite with 5 wt% $ZrO_2$ is considered to be appropriate as material for a ceramic heater.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.304-304
• /
• 2007

고주파 모률에서 사용되는 기판소재는 저유전율과 낮은 loss 특성을 요구함으로 지속적인 연구를 필요로 한다. 지금까지의 ceramic/glass composite 에서 주로 사용된 ceramic filler는 Al2O3로 낮은 유전률을 구현에 한계가 있었다. Cordierite는 낮은 유전율 (${\varepsilon}_r$ < 4)을 나타내는 filler로서 그 가능성이 높지만 아직까지 보고된 결과들이 미흡한 실정이다. 따라서 본 연구에서는 cordierite filler와 SiO2-B2O3-Al2O3-RO (R : Zn, Sr, Ba, Ca)계의 glass를 혼합하여 LTCC용 기판소재로서의 가능성을 확인하고자 저온 동시소성이 가능한 소결온도인 $850^{\circ}C{\sim}1.000^{\circ}C$ 사이에서 소재의 소결실험을 진행하였다. 소결온도에 따른 상변화, 유전특성을 확인한 결과 filler로 사용된 cordierite상만이 관찰 되었으며 소결조건에 따라 5.0~5.5의 낮은 유전율과 1.000~1,500의 Q를 나타내는 것을 확인 하였다.

• Journal of the Korean Ceramic Society
• /
• v.12 no.4
• /
• pp.29-36
• /
• 1975

Korean clinochlore, kaolin, pyrophillite and a technical grade of alumina have been used to investigate the effects of Al2O3 on the formation and properties of cordierite bodies. The body compositions were formulated from the proper proportions of the above raw materials to cover the range of composition from the point corresponding to the stoichiometric formula of cordierite, bythe consecutive increasment of 0.2mol. Al2O3, toward the apex of Al2O3 on the MgO-Al2O3-SiO2 triaxial diagram. Each of bodies was fired with the elevated temperatures from 110$0^{\circ}C$ to 140$0^{\circ}C$ by 5$0^{\circ}C$ interval. Linear shrinkage and water absorption were taken as measures for the firing range of the bodies. The formation of cordierite was estimated from the comparative study of X-ray diffraction and dilatometry of the fired bodies. The formation of a large amount of cordierite was initiated about 120$0^{\circ}C$. The content of Al2O3 exceeded up to 0.8 mol. comparing to the stoichiometric formula of cordierite broadens the firing range of the body.

• Journal of the Korean Ceramic Society
• /
• v.27 no.5
• /
• pp.625-630
• /
• 1990

Cordierite powders were prepared from Si(OC2H5)4, Al(OC3H7i)3 and Mg(OC2H5)2 by the sol-gel method. Two different methods were applied for producing fine and homogeneous powders. One is that Si(OC2H5)4 with a lowr rate of hydrolysis was partially hydrolyzed and then Al(OC3H7i)3 and Mg(OC2H5)2 were mixed and reacted. The other is based on the simultaneous hydrolysis of these metal alkoxides using i-C4H9OH which retards the rate of hydrolysis of Al(OC3H7i)3 and Mg(OC2H5)2. It was confirmed that ifne and homogeneous powders were obtained from both methods. Also these powders were calcined at four different temperatures during two hours. X-ray diffraction patterns show only ${\mu}$-cordierite phase at 1000$^{\circ}C$, ${\mu}$-cordierite and ${\alpha}$-cordierite phases at 1100-1200$^{\circ}C$ and ${\alpha}$-cordierite phase at 1300$^{\circ}C$ respectively.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.155-164
• /
• 2005

The characteristics of sintering for Mullite-Cordierite (MC) composites and the effect of $TiO_2$ addition were studied. The MC composites were manufactured by a solution-polymerization method using PVA as a polymer carrier, and $TiO_2$ was used as a sintering agent. They were calcined at $1300^{\circ}C$, planetary milled for 4 h and sintered at $1450^{\circ}C$. As cordierite content increased, relative density of materials was increased up to $98\%$ and sinterability was improved. In case of $50\;wt\%$ mullite/$5\;wt\%$ cordierite composition sintered for 16 h, the flexural strength and thermal expansion coefficient were 190 MPa and $3.07{\times}0^{-6}/^{\circ}C$, respectively. However, mechanical properties were decreased with the cordierite contents higher than $50\;wt\%$ because of the excess liquid-phase amount. As the addition of $TiO_2$ is increased, columnar crystal of mullite and liquid-phase contents were increased. In particular, the flexural strength and thermal expansion coefficient decreased in case of $5\;wt\%\;TiO_2$ addition.

• Journal of the Korean Ceramic Society
• /
• v.25 no.4
• /
• pp.397-407
• /
• 1988

Spinel, mullite and cordierite powders have synthesized from Mg(NO3)2.6H2O, Al(NO3).9H2O and SiCl4 solution by spray pyrolysis method. The two-fluid nozzle was used as an atomizer. The powders of sinel and mullite were synthesized above 80$0^{\circ}C$, but the cordierite composition was noncrystalline for all synthersizing temperature. Those noncrystalline powders were crystallized to $\alpha$-cordierite during calcining at 130$0^{\circ}C$ for 2hrs. The synthesized spinel, mullite and cordierite powders seem to be consisted of agglomerated hollow spherical particles. For all powders, the particle size ranged from submicron to about 3${\mu}{\textrm}{m}$ and mean particle size was about 1.4${\mu}{\textrm}{m}$ in diameter. The specific surface area values of spinel, mullite and cordierite powders were maximum for powders prepared at 100$0^{\circ}C$, and those were 45.9, 25.8 and 13.6$m^2$/gr, respectively.

• Journal of Powder Materials
• /
• v.17 no.1
• /
• pp.44-51
• /
• 2010

The rheological behavior of a cordierite honeycomb extrusion paste was investigated by measuring torque values in a Brabender plastograph. The extrusion pastes were formulated using binder (methy cellulose, MC), solvent (water), plasticizer (ploy ethylene glycol, PEG) and lubricants (oleic acid, OA). The mixing sequence and optimum organic binder, at least for homogeneous mixed state, can be determined from the rheological point of view. 3%MC-30%$H_2O$-1.5%PEG-1.0%OA with respect to the cordierite powder was chosen as a binder composition for the extrusion process of cordierite powder.