• 한국항공우주학회지
• /
• 제37권9호
• /
• pp.939-945
• /
• 2009

액체로켓 연소기 재생냉각 챔버의 제작에 사용되는 구리합금의 성형한계 곡선을 얻기 위하여 돔 장출 시험과 인장시험을 수행하였다. 성형한계 곡선에 대한 실험적인 연구를 위하여 인장시편을 사용하여 인장-압축 변형률 상태의 데이터를 얻었으며, 인장-인장의 변형률 상태를 얻기 위하여 돔 장출 시험용 시편을 사용한 돔 장출 시험 또한 수행하였다. 시험에 사용한 모든 시편은 제작방향에 따라 종 방향과 횡 방향시편으로 구분하였다. 시험 결과 인장-인장 변형률 상태에서 최대 주 변형률과 부 변형률은 62.3%와 58.6%이며, 인장-압축 상태에서는 60.5%와 25.8%로 나타났다.

• 한국광학회지
• /
• 제11권6호
• /
• pp.379-384
• /
• 2000

레이저 냉각법을 이용하여 세슘 원자의 온도를 도플러 냉각 한계온도 보다 낮은 온도까지 냉각하였다. 자기-광 포획된 원자를 더 냉각하기 위해서는 냉각용 레이저의 주파수를 더 적색편이 시켜야 하는데, 이를 위해 본 연구에서는 세슘 원자 흡수선의 Zeeman 이동을 이용하였다. 이 방법으로 레이저 주파수 안정화를 유지하면서 레이저의 주파수를 약 40MHz 만큼 이동시킬수 있었다. 비행시간 방법으로 측정한 레이저 냉각된 세슘원자의 최저온도는 $2.2\muK$\pm$0.5$\muK$이었다. 냉각된 원자의 온도를 레이저의 주파수 및 세기에 따라 측정하였는데, 이광자 냉각 이론에 의한 계산결과와 잘 일치한다는 것을 알았다.

• 한국환경과학회지
• /
• 제27권12호
• /
• pp.1261-1269
• /
• 2018

The purpose of this study was to investigate changes in the external thermal environment, following the application of evaporative cooling systems in buildings, in response to climate change. In order to verify changes in the external thermal environment, a T-test was performed on the microclimate, Thermal Comfort Index (TCI), and building surface temperature. Differences in microclimate, following the application of the evaporative cooling system in the building, were significant in terms of temperature and relative humidity. In particular, temperature decreased by more than 7% when the evaporative cooling system was applied. According to the results of the Thermal Comfort Index analysis, the Wet-Bulb Globe Temperature (WBGT) was below the limit of outdoor activities, indicating that outdoor activities were possible. The Universal Thermal Climate Index (UTCI) values were within the very strong heat stress range when the evaporative cooling system was not applied, When the system was applied, the UTCI values were within the strong heat stress range, indicating that they were lowered by one level. The building surface temperature decreased by ~10% or more when the evaporative cooling system was applied, compared to when it was not applied. Finally, the outside surface temperature of the building decreased by ~12% or more when the system was applied, compared to when it was not applied. We conclude that the energy saving effect of the building was significant.

• 한국초전도ㆍ저온공학회논문지
• /
• 제8권2호
• /
• pp.29-32
• /
• 2006

An advanced superconducting fault current limiter (SFCL) using $high-T_c$ superconducting (HTS) wire has been developed. The SFCL has a non-inductively wound magnet for reducing loss in normal state. Two types of non-inductively wound magnets, the solenoid type and the pancake type, were designed and manufactured by using Bi-2223 wire in this research. Short-circuit tests of the magnets were performed in sub-cooled $LN_2$ cooling system of 65 K. The magnets are thermally more stable and have a higher critical current in 65 K sub-cooled $LN_2$ cooling system than in 77 K saturated one. Because the resistivity of matrix at 65 K is lower than the resistivity at 77 K, the magnets generate a small resistance to reduce the fault current when the quench occurs. The magnets could limit the fault current to low current level with such a small resistance. The current limiting characteristic of the magnets was analyzed from the test result. The solenoid type was wound in parallel to make it non-inductive. The pancake type was also connected in parallel to be compared with the solenoid type in the same condition. The solenoid type was found to have a good thermal stability compared with the pancake type. It also had as large resistance as the pancake type to limit the fault current in sub-cooled $LN_2$ cooling system.

• Journal of Mechanical Science and Technology
• /
• 제18권5호
• /
• pp.820-829
• /
• 2004

The In-Containment Refueling Water Storage Tank (IRWST), one of the design improvements applied to the APR -1400, has a function to condense the high enthalpy fluid discharged from the Reactor Coolant System (RCS). The condensation of discharged fluid by the tank water drives the tank temperature high and causes oscillatory condensation. Also if the tank cooling water temperature approaches the saturated state, the steam bubble may escape from the water uncondensed. These oscillatory condensation and bubble escape would burden the undue load to the tank structure, pressurize the tank, and degrade its intended function. For these reasons simple analytical modeling and experimental works were performed in order to predict exact tank temperature distribution and to find the effective cooling method to keep the tank temperature below the bubble escape limit (93.3$^{\circ}C$), which was experimentally proven by other researchers. Both the analytical model and experimental results show that the temperature distributions are horizontally stratified. Particularly, the hot liquid produced by the condensation around the sparger holes goes up straight like a thermal plume. Also, the momentum of the discharged fluid is not so strong to interrupt this horizontal thermal stratification significantly. Therefore the layout and shape of sparger is not so important as long as the location of the sparger hole is sufficiently close to the bottom of the tank. Finally, for the effective tank cooling it is recommended that the locations of the discharge and intake lines of the cooling system be cautiously selected considering the temperature distribution, the water level change, and the cooling effectiveness.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.323-328
• /
• 2005

The objective of this study is to analyze the cooling performance of an air- cooling system for telecommunication equipment. Temperature variation and capacity were measured in an actual unit for telecommunication equipment. In addition, the cooling performance was measured by installing a silicon rubber heater as a heat source in a cabinet. The standard thermal load for telecommunication equipment was approximately 293 W, and the maximum temperature of the heated surface was $64.5^{\circ}C$. The average and maximum temperatures of the heated surface were proportional to the inlet air temperature. When the heat load increased from 293 W to 400 W, the maximum temperature of the heated surface was higher than $64.5^{\circ}C$ even though the inlet air temperature decreased from 25 to $11^{\circ}C$.

• 대한금속재료학회지
• /
• 제50권10호
• /
• pp.735-743
• /
• 2012

The aim of this study was to analyze the effect of the cooling rate after heat treatment on the microstructure and mechanical properties of 2507 duplex stainless steels. Heat treatment was carried out at $1050^{\circ}C$ for 1 hr, followed by controlled cooling. The cooling rates were $175.6{\times}10^{-3}^{\circ}C/s$, $47.8{\times}10^{-3}^{\circ}C/s$, $33.3{\times}10^{-3}^{\circ}C/s$, $16.7{\times}10^{-3}^{\circ}C/s$, $11.7{\times}10^{-3}^{\circ}C/s$, $5.8{\times}10^{-3}^{\circ}C/s$ and $2.8{\times}10^{-3}^{\circ}C/s$, which resulted in variations of the microstructure, such as the fractional change of the ferrite phase and sigma phase formation. Fatigue, hardness, impact and tensile tests were performed on the specimens with different cooling rates. The precipitation of the ${\sigma}$ phase caused a hardness increase and a sharp decrease of toughness and tensile elongation. The fatigue limit of the sample with a cooling rate of $5.8{\times}10^{-3}^{\circ}C/s$ was 26 MPa higher than that of the sample with a cooling rate of $175.6{\times}10^{-3}^{\circ}C/s$. Our observations of the fracture surface confirmed that the higher fatigue resistance of the specimen with a cooling rate of $5.8{\times}10^{-3}^{\circ}C/s$ was caused by the delay of the fatigue crack growth, in addition to higher yield strength.

• Journal of the Optical Society of Korea
• /
• 제7권2호
• /
• pp.119-125
• /
• 2003

We demonstrate parametric resonance in a magneto-optical trap. When we modulate the intensity of the cooling laser at about twice the resonant frequency of the trap, the atoms in the trap are divided into two parts and oscillate with 180 degree phase difference with the finite length due to nonlinearity of the trap potential. These are the effects of general nonlinear dynamics, called the Hopf bifurcation, or limit cycle motion. The amplitude and the phase of the oscillations are measured and compared with the theoretical calculations based on simple Doppler cooling theory. The experimental results are in excellent agreement with the simulation results based on the simple Doppler cooling theory.

• 대한기계학회논문집A
• /
• 제25권10호
• /
• pp.1567-1574
• /
• 2001

In order to operate an RPV safely it is necessary to keep the pressure-temperature (P-T) limit during the heatup and cooldown process. While the ASME Code provides the P-T limit curve for safe operation, this limit curve has been prepared under conservative assumptions In this paper the effects of conservative assumptions involved in the P-T limit curve specified in the ASME Code Sec. XI were investigated. Three different parameters the crack depth the cladding thickness and the cooling rate, were reviewed based on 3-D finite element analyses. Also the constraint effect on P-T limit curve generation was investigated based on J- T approach. It was shown that the crack depth and the constraint effect change the safe region in P-T limit curve significantly Therefore it is recommended to prepare a more precise P-T limit curve based on finite element analysis to obtain P-T limit for safe operation of an RPV.

• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.935-941
• /
• 2010

하나로는 한국에 설치되어 있는 열출력 30MW의 개방 수조형 연구로 이다. 이는 발전로와 달리 원자로에서 발생하는 열을 이용하여 전기를 생산하는 것 대신에 원자로의 노심 온도를 유지하기 위하여 냉각탑을 통해 대기로 이 열을 냉각한다. 냉각탑 월간 점검 중에 냉각탑 4번의 냉각팬 감속기가 기준을 상회하는 고진동을 기록하였다. 본 연구의 목적은 고진동의 원인을 찾아 정상적으로 수리하기 위함이다. 연구 방법은 FFT 스펙트럼 기법을 적용하여 고진동의 원인을 분석하였다. 그 결과 고진동 주파수는 피니언 기어의 고유 진동수의 두 배인 354Hz이었다. 피니언 기어를 점검한 결과 이빨 표면이 깨져 있었다. 깨진 피니언 기어를 제거하고 새것으로 교체한 후에는 감속기는 정상적으로 작동하였다.