• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.851-856
• /
• 2003

We have investigated the material and electrical properties of $Bi_{4-x}La_xTi_3O_{12}$ (BLT) ferroelectric thin film for ferroelectric nonvolatile memory applications of capacitor type and single transistor type. The 120nm thick BLT films were deposited on $Pt/Ti/SiO_2/Si$ and $SiO_2/Nitride/SiO_2$ (ONO) substrates by the sol-gel spin coating method and were annealed at $700^{\circ}C$. It was observed that the crystallographic orientation of BLT thin films were strongly affected by the excess Bi content and the intermediate rapid thermal annealing (RTA) treatment conditions regardeless of two type substrates. However, the surface microstructure and roughness of BLT films showed dependence of two different type substrates with orientation of (111) plane and amorphous phase. As increase excess Bi content, the crystallographic orientation of the BLT films varied drastically in BLT films and exhibited well-crystallized phase. Also, the conversion of crystallographic orientation at intermediate RTA temperature of above $450^{\circ}C$ started to be observed in BLT thin films with above excess 6.5% Bi content and the rms roughness of films is decreased. We found that the electrical properties of BLT films such as the P-V hysteresis loop and leakage current were effectively modulated by the crystallographic orientations change of thin films.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.5
• /
• pp.462-469
• /
• 2014

As a basic study on both engineering applications and representation methods of synesthesia, this paper aims at building basic system which converts a muscular sense into both visual and auditory elements. As for the building method, data of the muscular sense can be acquired through roll and pitch signals which are calculated from both three-axis acceleration sensor and the two-axis gyro sensor. The roll and pitch signals are then converted into both visual and auditory information as outputs. The roll signals are converted into both intensity elements of the HSI color model and octaves as one of auditory elements. In addition, the pitch signals are converted into both hue elements of the HSI color model and scales as another one of auditory elements. Each of the extracted elements of the HSI color model is converted into each of the three elements of the RGB color model respectively, so that the real-time output color signals can be obtained. Octaves and scales are also converted and synthesized into MIDI signals, so that the real-time sound signals can be obtained as anther one of output signals. In experiments, the results revealed that normal color and sound output signals were successfully obtained from roll and pitch values that represent muscular senses or physical movements, depending on the conversion relationship based on the similarity between color and sound.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.9
• /
• pp.936-943
• /
• 2013

This work presents the design and measured results of the single channel automotive radar system for 76.5~77 GHz long range FMCW radar applications. The transmitter uses a commercial GaAs monolithic microwave integrated circuit(MMIC) and the receiver uses the down converter designed using 65 nm CMOS process. The output power of the transmitter is 10 dBm. The down converter chip can operate at low LO power as -8 dBm which is easily supplied from the transmitter output using a coupled line coupler. All MMICs are mounted on an aluminum jig which embeds the WR-10 waveguide. A microstrip to waveguide transition is designed to feed the embedded waveguide and finally high gain horn antennas. The overall size of the fabricated radar system is $80mm{\times}61mm{\times}21mm$. The radar system achieved an output power of 10 dBm, phase noise of -94 dBc/Hz at 1 MHz offset and a conversion gain of 12 dB.

• Solar Energy
• /
• v.17 no.4
• /
• pp.3-11
• /
• 1997

Because grain boundaries in polycrystalline silicon act as potential barriers and recombination centers for the photo-generated charge carriers, these defects degrade conversion effiency of solar cell. To reduce these effects of grain boundaries, we investigated various influencing factors such as thermal treatment, various grid pattern, selective wet etching for grain boundaries, buried contact metallization along grain boundaries, grid on metallic thin film. Pretreatment above $900^{\circ}C$ in $N_2$ atmosphere, gettering by $POCl_3$ and Al treatment for back surface field contributed to obtain a high quality poly-Si. To prevent carrier losses at the grain boundaries, we carried out surface treatment using Schimmel etchant. This etchant delineated grain boundaries of $10{\mu}m$ depth as well as surface texturing effect. A metal AI diffusion into grain boundaries on rear side reduced back surface recombination effects at grain boundaries. A combination of fine grid with finger spacing of 0.4mm and buried electrode along grain boundaries improved short circuit current density of solar cell. A ultra-thin Chromium layer of 20nm with transmittance of 80% reduced series resistance. This paper focused on the grain boundary effect for terrestrial applications of solar cells with low cost, large area, and high efficiency.

• Food Engineering Progress
• /
• v.14 no.4
• /
• pp.292-298
• /
• 2010

Wheat germ contains the glycosylated forms of 2-methoxy-p-benzoquinone (2-MBQ) and 2,6-dimethoxy-p-benzoquinone (2,6-DMBQ), both of which have antimicrobial and immunostimulatory effects. Conversion of glycosylated 2-MBQ and 2,6-DMBQ to their more functional unglycosylated forms requires enzymatic action of $\beta$-glucosidase. We investigated the applications of lactic acid bacteria and yeast that produce $\beta$-glucosidase as starters for production of unglycosylated 2-MBQ and 2,6-DMBQ from wheat germ. Lactobacillus zeae and Pichia pijperi were selected through $\beta$-glucosidase enzyme assays for 37 yeast strains and five strains of lactic acid bacteria. Lb. zeae was more efficient than P. pijperi at producing 2-MBQ and 2,6-DMBQ from wheat germ. After 48 hr of fermentation with a mixed culture of Lb. zeae and P. pijperi, the concentration of 2-MBQ was 0.46${\pm}$0.07 mg/g, indicating an approximately 1.6-fold higher concentration than that obtained by pure culture of Lb. zeae. However, the concentration of 2,6-DMBQ was not significantly enhanced by fermentation with a mixed culture of Lb. zeae and P. pijperi.

• Korean Journal of Food Science and Technology
• /
• v.46 no.2
• /
• pp.189-197
• /
• 2014

Onion juices were prepared by various heat treatments (at $105-120^{\circ}C$ for 4.5-5.5 h), from the onions cultivated with increasing numbers of sulfur applications (once for Sulfur-1, four times for Sulfur-4). As heat treatment intensity increased, the onion juices darkened (p<0.001), which adversely affected the sensory preference. In addition, increasing the heating temperature significantly increased the organic acid content of onion juices (p<0.001), and therefore, decreased pH (p<0.001). Heat intensity did not affect the thiosulfinate content of onion juices, suggesting that the rate of decomposition of thiosulfinate into low-molecular weight sulfur derivatives is similar over the temperature range of $105-120^{\circ}C$. Total flavonoids were higher in onion juices derived from Sulfur-4 than in Sulfur-1 onions, and increased with heat treatment intensity (p<0.001). These results indicated that heat-facilitated conversion of bound forms of flavonoids to their free forms increases the extractability of flavonoids from onions.

• Corrosion Science and Technology
• /
• v.9 no.4
• /
• pp.147-152
• /
• 2010

Conventional paints for conversion coating applications in steel production derived mainly from water-based polymer dispersions containing several additives actually show good general performance, but suffer from poor scratch and abrasion resistance during use. The reason for this is because the relatively soft organic binder matrix dominates the mechanical surface properties. In order to maintain the high quality and decorative function of coated steel sheets, the mechanical performance of the surface needs to be improved significantly. In fact the wear resistance should be enhanced without affecting the optical appearance of the coatings by using appropriate nanoparticulate additives. In this direction, nanocomposite coating compositions (Nanomer$^{(R)}$) have been derived from water-based polymer dispersions with an increasing amount of surface-modified nanoparticles in aqueous dispersion in order to monitor the effect of degree of filling with rigid nanoparticles. The surface of nanoparticles has been modified for optimum compatibility with the polymer matrix in order to achieve homogeneous nanoparticle dispersion over the matrix. This approach has been extended in such a way that a more expanded hybrid network has been condensed on the nanoparticle surface by a hydrolytic condensation reaction in addition to the quasi-monolayer type small molecular surface modification. It was expected that this additional modification will lead to more intensive cross-linking in coating systems resulting in further improved scratch-resistance compared to simple addition of nanoparticles with quasi-monolayer surface modification. The resulting compositions have been coated on zinc-galvanized steel and cured. The wear resistance and the corrosion protection of the modified coating systems have been tested in dependence on the compositional change, the type of surface modification as well as the mixing conditions with different shear forces. It has been found out that for loading levels up to 50 wt.-% nanoparticles, the mechanical wear resistance remains almost unaffected compared to the unmodified resin. In addition, the corrosion resistance remained unaffected even after $180^{\circ}$ bending test showing that the flexibility of coating was not decreased by nanoparticle addition. Electron microscopy showed that the inorganic nanoparticles do not penetrate into the organic resin droplets during the mixing process but rather formed agglomerates outside the polymer droplet phase resulting in quite moderate cross linking while curing, because of viscosity. The proposed mechanisms of composite formation and cross linking could explain the poor effect regarding improvement of mechanical wear resistance and help to set up new synthesis strategies for improved nanocomposite morphologies, which should provide increased wear resistance.

• Resources Recycling
• /
• v.22 no.4
• /
• pp.38-45
• /
• 2013

The porous ceramic beads using mine tailing were prepared and applied to catalytic converter for NOx/SOx removal. Catalytic support was used synthesized mesoporous silica (SBA-15) which coated on surface. Internal structure for porous ceramic beads was composed of three-dimensional network structure and porosity was about 80%. In addition, the specific surface area for mesoporous silica(SBA-15) coated on converter was significantly increased 55 $m^2/g$ compared with 0.8 $m^2/g$ before coating. NOx/SOx removal experiment was performed using $V_2O_5$ and $V_2O_5$/CuO converter. NOx conversion ratio for $V_2O_5$/CuO converter was approximately increased 10% compared to $V_2O_5$ converter. In addition, catalytic converter of $V_2O_5$/CuO was shown to remove 95% of NOx and 90% of SOx at reaction temperature of $350^{\circ}C$, space velocity of 10000 $h^{-1}$ and $O_2$ concentrations of 5%, respectively.

• Journal of Internet Computing and Services
• /
• v.22 no.6
• /
• pp.33-40
• /
• 2021

Automatic Speech Recognition(ASR) is a technology that analyzes human speech sound into speech signals and then automatically converts them into character strings that can be understandable by human. Speech recognition technology has evolved from the basic level of recognizing a single word to the advanced level of recognizing sentences consisting of multiple words. In real-time voice conversation, the high recognition rate improves the convenience of natural information delivery and expands the scope of voice-based applications. On the other hand, with the active application of speech recognition technology, concerns about related cyber attacks and threats are also increasing. According to the existing studies, researches on the technology development itself, such as the design of the Automatic Speaker Verification(ASV) technique and improvement of accuracy, are being actively conducted. However, there are not many analysis studies of attacks and threats in depth and variety. In this study, we propose a cyber attack model that bypasses voice authentication by simply manipulating voice frequency and voice speed for AI voice recognition service equipped with automated identification technology and analyze cyber threats by conducting extensive experiments on the automated identification system of commercial smartphones. Through this, we intend to inform the seriousness of the related cyber threats and raise interests in research on effective countermeasures.

• Applied Chemistry for Engineering
• /
• v.26 no.6
• /
• pp.640-647
• /
• 2015

As the need for next-generation flexible electronics grows, novel materials and technologies that can replace conventional indium tin oxide (ITO) for transparent electrodes have been of great interest. Among them, a conducting polymer, especially poly(3,4-ethylenedioxythiophene) : poly(styrene sulfonate) (PEDOT : PSS) is one of the most promising candidates because it is mechanically flexible, inexpensive, and capable of being processed in solution. Currently, there are a lot of research efforts on enhancing its electrical conductivity to the level of ITO or metal electrodes through chemical and/or physical processing. In this review article, we present various additives and pre-/post-deposition processing methods for improving the electrical conductivity of PEDOT : PSS. Some of representative reports are also introduced, which demonstrated the use of conductivity-enhanced PEDOT : PSS as transparent electrodes in electronics and energy conversion.