• Clean Technology
• /
• v.24 no.4
• /
• pp.307-314
• /
• 2018

In this study, NMO (Natural Manganese Ore), $MnO_2$, and $Mn_2O_3$ catalysts were used in the selective catalytic reduction process to remove nitrogen oxides (NOx) using $NH_3$ as a reducing agent at low temperatures in the presence of oxygen. In the case of the NMO (Natural Manganese Ore), it was confirmed that the conversion of nitrogen oxides in the stability test did not change even after 100 hours at 423 K. The Kinetics experiments were carried out within the range where heat and mass transfer were not factors. From a steady-state Kinetics study, it was found that the low-temperature SCR reaction was zero order with the respect to $NH_3$ and 0.41 ~ 0.57 order with the respect to NO and 0.13 ~ 0.26 order with the respect to $O_2$. As temperature increases, the reaction order decreases as a result of $NH_3$ and oxygen concentration. It was confirmed that the reaction between the $NH_3$ dissociated and adsorbedon the catalyst surface and the gaseous nitrogen monoxide (E-R model) and the reaction with the adsorbed nitrogen monoxide (L-H model) occur.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1012-1018
• /
• 2018

In this paper, CMOS SAR (Successive Approximation Register) A/D converter with 1.8V supply voltage is designed for IoT sensor processing. This paper proposes design of a 12-bit SAR A/D converter with two A / D converters in parallel to improve the sampling rate. A/D converter1 of the two A/D converters determines all the 12-bit bits, and another A/D converter2 uses the upper six bits of the other A/D converters to minimize power consumption and switching energy. Since the second A/D converter2 does not determine the upper 6 bits, the control circuits and SAR Logic are not needed and the area is minimized. In addition, the switching energy increases as the large capacitor capacity and the large voltage change in the C-DAC, and the second A/D converter does not determine the upper 6 bits, thereby reducing the switching energy. It is also possible to reduce the process variation in the C-DAC by proposed structure by the split capacitor capacity in the C-DAC equals the unit capacitor capacity. The proposed SAR A/D converter was designed using 0.18um CMOS process, and the supply voltage of 1.8V, the conversion speed of 10MS/s, and the Effective Number of Bit (ENOB) of 10.2 bits were measured. The area of core block is $600{\times}900um^2$, the total power consumption is $79.58{\mu}W$, and the FOM (Figure of Merit) is 6.716fJ / step.

• Journal of the Korea Convergence Society
• /
• v.10 no.5
• /
• pp.1-8
• /
• 2019

In this paper, we propose an improved facial skin color extraction method to solve the problem that facial surface is lost due to shadow or illumination in skin color extraction process and skin color extraction is not possible. In the conventional HSV method, when facial surface is brightly illuminated by light, the skin color component is lost in the skin color extraction process, so that a loss area appears on the face surface. In order to solve these problems, we extract the skin color, determine the elements in the H channel value range of the skin color in the HSV color space among the lost skin elements, and combine the coordinates of the lost part with the coordinates of the original image, To minimize the number of In the face detection process, the face was detected using the LBP Cascade Classifier, which represents texture feature information in the extracted skin color image. Experimental results show that the proposed method improves the detection rate and accuracy by 5.8% and 9.6%, respectively, compared with conventional RGB and HSV skin color extraction and face detection using the LBP cascade classifier method.

• Journal of odor and indoor environment
• /
• v.17 no.4
• /
• pp.355-361
• /
• 2018

Mold grows more easily when humidity is higher in indoor spaces, and as such is found more often on wetted areas in housing such as walls, toilets, kitchens, and poorly managed spaces. However, there have been few studies that have specifically assessed the level of mold in the indoor spaces of water-damaged housing in the Republic of Korea. We investigated the levels of airborne mold according to the characteristics of water damage types and explored the correlation between the distribution of mold genera and the characteristics of households. Samplings were performed from January 2016 to June 2018 in 97 housing units with water leakage or condensation, or a history of flooding, and in 61 general housing units in the metropolitan and Busan area, respectively. Airborne mold was collected on MEA (Malt extract agar) at flow rate of 100 L/min for 1 min. After collection, the samples were incubated at $25^{\circ}C$ for 120 hours. The cultured samples were counted and corrected using a positive hole conversion table. The samples were then analyzed by single colony culture, DNA extraction, gene amplification, and sequencing. By type of housing, concentrations of airborne mold were highest in flooded housing, followed by water-leaked or highly condensed housings, and then general housing. In more than 50% of water-damaged housing, the level of airborne mold exceeded the guideline of Korea's Ministry of Environment ($500CFU/m^3$). Of particular concern was the fact that the I/O ratio of water-damaged housing was greater than 1, which could indicate that mold damage may occur indoors. The distribution patterns of the fungal species were as follows: Penicillium spp., Cladosporium spp. (14%), Aspergillus spp. (13%) and Alternaria spp. (3%), but significant differences of their levels in indoor spaces were not found. Our findings indicate that high levels of mold damage were found in housing with water damage, and Aspergillus flavus and Penicillium brevicompactum were more dominant in housing with high water activity. Comprehensive management of flooded or water-damaged housing is necessary to reduce fungal exposure.

• Journal of Korean Foot and Ankle Society
• /
• v.25 no.3
• /
• pp.111-116
• /
• 2021

Purpose: Variations in the preferred conservative and operative treatment methods for ankle arthritis may be observed in the practice of orthopedic surgeons. This study is based on the Korean Foot and Ankle Society (KFAS) member survey and aims to report the current trend and changes in the management of ankle arthritis over the last few decades. Materials and Methods: A web-based questionnaire containing 24 questions was sent to all KFAS members in July 2021. The questions were mainly related to the preferred techniques and clinical experience in osteotomy, arthrodesis, and total ankle arthroplasty (TAA) for patients with ankle arthritis. Results: Sixty-three out of 550 surgeons (11.5%) responded to the survey. The responses to 6 out of the total of 24 questions (25.0%) achieved the levels needed to reflect a tendency. Answers that showed a tendency were related to the following: a surgical approach for arthrodesis (anterior approach), use of auto-bone graft for arthrodesis (iliac bone), a nonunion rate of more than 10% following arthrodesis, main reason related to unsatisfactory results after arthrodesis (nonunion or delayed union), the main reason to change total ankle prosthesis (unstable supply of prosthesis), the unusualness of revision TAA and conversion of fusion to TAA. Diversity was found in several aspects of treatment (degree of experience and satisfaction in supramalleolar osteotomy, fixation method for arthrodesis, preferred TAA prosthesis and longevity, degree of experinece, annual number of TAA operation. Conclusion: This study proposes updated information with regard to the current trends in the management of ankle arthritis in Korea. Both consensus and variations in the approach to patients with ankle arthritis were identified through this survey. With an increasing preference for TAA, the need for the development of a prosthesis optimized for Koreans and a stable supply of prostheses were the suggestions made by the study.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.4
• /
• pp.101-108
• /
• 2022

This study analyzed the physicochemical properties and combustion characteristics of dry food waste to evaluate the possibility of using food waste as a solid refuse fuel (SRF). The characteristics of dry food waste as a fuel were analyzed by comparing the difference in properties with SRF, and the combustion characteristics after conversion into fuel were identified. Ultimate analysis, proximate analysis, calorific value analysis, and TGA analysis were conducted using two types of food waste and two types of SRF, and the following results were obtained. The moisture content and ash content of dry food waste were 1.7~10.0 wt.% and 7.8~11.7 wt.%, respectively, which satisfied the quality standards for SRF. The low calorific value of dry food waste was 4,000 ~ 4,720 kcal/kg, which was higher than the quality standard of 3,500 kcal/kg for SRF. As a result of TGA analysis of dry food waste, the combustion reaction started at about 200 ℃ and the highest burning rate was at about 500 ℃. After moisture evaporation between 100 and 200 ℃, initial volatile matter, carbon and residual volatile matter were released and burned between 200 and 500 ℃. Based on the high calorific value and low moisture and ash content of dry food waste, it is considered that it is possible to convert dry food waste into SRF through the application of efficient drying technology and strict quality standard inspection in the future.

• Animal Bioscience
• /
• v.34 no.3_spc
• /
• pp.434-442
• /
• 2021

Objective: This study aims to evaluate the influence of dietary flavonoids on the growth performance, blood and intestinal profiles, and carcass characteristics of broilers by employing a meta-analysis method. Methods: A database was built from published studies which have reported on the addition of various levels of flavonoids from herbs into broiler diets and then monitored growth performance, blood constituents, carcass proportion and small intestinal morphology. A total of 42 articles were integrated into the database. Several forms of flavonoids in herbs were applied in the form of unextracted and crude extracts. The database compiled was statistically analyzed using mixed model methodology. Different studies were considered as random effects, and the doses of flavonoids were treated as fixed effects. The model statistics used were the p-values and the Akaike information criterion. The significance of an effect was stated when its p-value was <0.05. Results: Dietary flavonoids increased (quadratic pattern; p<0.05) the average daily gain of broilers in the finisher phase. There was a reduction (p<0.01) in the feed conversion ratio of the broilers both in the starter (linear pattern) and finisher phases (quadratic pattern). The mortality rate tended to decrease linearly (p<0.1) with the addition of flavonoids, while the carcass parameter was generally not influenced. A reduction (p<0.001) in cholesterol and malondialdehyde concentrations (both linearly) was observed, while super oxide dismutase activity increased linearly (p<0.001). Increasing the dose of flavonoids increased (p<0.01) the villus height (VH) and villus height and crypt depth (VH:CD) ratio (p<0.05) in the duodenum. Similarly, the VH:CD ratio was elevated (p<0.001) in the jejunum following flavonoid supplementation. Conclusion: Increasing levels of flavonoids in broilers diet leads to an improvement in growth performance, blood constituents, carcass composition and small intestinal morphology.

• Applied Chemistry for Engineering
• /
• v.32 no.3
• /
• pp.326-331
• /
• 2021

In this study, the preparation conditions for a TiO₂-based vanadium-based catalyst for oxidizing hydrogen sulfide at room temperature were optimized. Four types of commercial TiO₂ were used as a catalyst support and the performance evaluation of hydrogen sulfide oxidation at room temperature of V/TiO₂ by varying vanadium contents prepared using the impregnation method was performed. Among the types of TiO₂ tested, it was confirmed that the catalyst with the vanadium content of 5% and based on TiO₂(A) has the best hydrogen sulfide conversion rate of 58%. By comparing the physical and chemical properties of the catalyst, the specific surface area of the support and the species of dominant vanadium are the major factor in catalyst performance. In order to confirm the regeneration characteristics of the catalyst with reduced activity, heat treatment was performed at 400 ℃ for 2 h, and the amount of hydrogen sulfide oxidation decreased by 10% due to the partial deposition of sulfur in the regenerated catalyst, but it was confirmed that the initial performance was similar.

• Animal Bioscience
• /
• v.34 no.4
• /
• pp.680-691
• /
• 2021

Objective: This study was conducted to investigate the effect of fermented cottonseed meal (FCSM) on growth performance, carcass traits, and fat deposition in white-feather broiler chickens. Methods: A total of 480 male one-day-old white-feather broiler chickens were selected randomly and divided into four groups with six replicates of 20 chickens in each. The experimental chickens were fed diets including 3%, 6%, or 9% FCSM fermented by Candida tropicalis until 42 days old. In the experiment, the chickens of the control group were fed soybean meal. Results: FCSM supplementation linearly decreased the feed conversion ratio from d 15 to 21 and d 36 to 42, respectively (p<0.05). The percentage of carcass and semi-eviscerate increased in response to dietary FCSM supplementation at d 21 (p<0.05). The percentage of eviscerated and semi-eviscerate of 3FCSM was higher than that in other groups at d 35 (p<0.05). At the age of 42 d, the percentage of carcass increased in a quadratic way among increasing FCSM in diets (p<0.05). The subcutaneous fat thickness linearly decreased with the increasing levels of FCSM at d 21 (p<0.05). Gompertz and Logistic functions provided a better fit on abdominal fat and subcutaneous fat, respectively. The best fitted equation predicted that the maximum growth rate of abdominal fat weight and subcutaneous fat thickness occurred at d 28. FCSM had no significant effects on the shape of growth curve of abdominal fat weight and subcutaneous fat thickness, but reduced the height of the curve. Birds receiving the 6FCSM diet for 21 d had smaller adipocyte surface and lower serum glucose as well as triglyceride concentration. Conclusion: FCSM is beneficial for broiler chickens as it positively affects their growth and carcass in addition to altering their fat deposition.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.1
• /
• pp.135-144
• /
• 2021

In this study, we investigated the characteristics of the process of hydrogen production using boil-of gas (BOG) generated from an LNG-fueled ship and the application of hydrogen fuel cell systems as auxiliary engines. In this study, the BOG steam reformer process was designed using the UniSim R410 program, and the reformer outlet temperature, pressure, and the fraction and consumption of the product according to the steam/carbon ratio (SCR) were calculated. According to the study, the conversion rate of methane was 100 % when the temperature of the reformer was 890 ℃, and maximum hydrogen production was observed. In addition, the lower the pressure, the higher is the reaction activity. However, higher temperatures have led to a decrease in hydrogen production owing to the preponderance of adverse reactions and increased amounts of water and carbon dioxide. As SCR increased, hydrogen production increased, but the required energy consumption also increased proportionally. Although the hydrogen fraction was the highest when the SCR was 1.8, it was confirmed that the optimal operation range was for SCR to operate at 3 to prevent cocking. In addition, the lower the pressure, the higher is the amount of carbon dioxide generated. Furthermore, 42.5 % of the LNG cold energy based on carbon dioxide generation was required for cooling and liquefaction.