• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2001년도 학술대회논문집
• /
• pp.181-185
• /
• 2001

This paper presents a digitally speed sensorless control system for induction motor with direct torque control (DTC). The drive is based on Mode1 Reference Adaptive System (MRAS) using state observer as a reference model fat flux estimation. The system are closed loop stator flux and torque observer for wide speed range that inputs are currents and voltages sensing of motor terminal, model reference adaptive control (MRAS) with rotor flux linkages for the speed turning aignal at low speed range, two hysteresis controllers. The Proposed system is verified through simulation.

• 제어로봇시스템학회논문지
• /
• 제21권11호
• /
• pp.1027-1033
• /
• 2015

For the attitude control of spacecraft, two variable-speed control moment gyros are proposed as main actuators in the article. Since a variable-speed control moment gyro (VSCMG) makes two control torques (gyroscopic torque and reaction torque), two VSCMGs are sufficient for controlling 3-axes attitude. Additionally, there are no singular conditions for two non-parallel VSCMGs. Since gyroscopic torque is usually much greater than reaction torque, the control performances of approximately 3 axes may not be the same. However, several missions can be accomplished by controlling two axes. For such missions, a selective axes control method is proposed. The method selects two axes for a certain task and controls the attitude of the selected axes. For the remaining axis, angular speed is controlled for stabilization. A hardware-in-the-loop simulation has been used to test VSCMG modules and to verify the proposed method. Two VSCMGs can be alternative actuators for small satellites.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권2호
• /
• pp.89-97
• /
• 2006

Interior permanent magnet synchronous motor(IPMSM) has become a popular choice in electric vehicle applications, due to their excellent power to weight ratio. The paper is proposed maximum torque control of IPMSM drive using learning mechanism-fuzzy neural network(LM-FNN) controller and artificial neural network(ANN). The control method is applicable over the entire speed range and considered the limits of the inverter's current and voltage rated value. For each control mode, a condition that determines the optimal d-axis current $i_{d}$ for maximum torque operation is derived. This paper considers the design and implementation of novel technique of high performance speed control for IPMSM using LM-FNN controller and ANN controller. The hybrid combination of neural network and fuzzy control will produce a powerful representation flexibility and numerical processing capability. Also, this paper is proposed speed control of IPMSM using LM-FNN and estimation of speed using ANN controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The proposed control algorithm is applied to IPMSM drive system controlled LM-FNN and ANN controller, the operating characteristics controlled by maximum torque control are examined in detail. Also, this paper is proposed the analysis results to verify the effectiveness of the LM-FNN and ANN controller.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권1호
• /
• pp.100-107
• /
• 2003

This study was to control magnetic field orientation-typed sensorless vector control by applying the theory of a rotor flux observer to drive an induction motor. This research suggested a new speed estimation method that estimates speed with the rotor flux obtained by using a flux observer and the variable of state current detected by a current sensor without a speed sensor. Because the speed estimation method is independent from the motor constants, it is not necessary to control the gain of the parameters and the algorithm is simple. In the findings of the study, the researcher was convinced of the control function and the possibility of realization in the simulation experiment of sensorless vector control system by using DSP(Digital Signal Prosessor).

• 풍력에너지저널
• /
• 제2권1호
• /
• pp.82-89
• /
• 2011

his dissertation is on power control system for MW-class wind turbine. Especially, the control purpose is reduction in electrical power and rotor speed. The base control structure is power curve tracking control using variable speed variable pitch operational type. For the reduction of fluctuations, more control algorithm is needed in above rated wind conditions. Because general pitch control system is low dynamic response as compared with the wind speed change. So, this paper introduces about the pitch feed forward control to minimize fluctuations of the electrical power and rotor speed. To maintain rated electrical power, the algorithm of feed forward control adds feed forward pitch amount to the pitch command of power curve tracking control. The effectiveness of the feed forward control is verified through the simulation.

• Wind and Structures
• /
• 제21권4호
• /
• pp.443-460
• /
• 2015

In this paper, an integrator based method to estimate the effective wind speed in wind turbine systems is proposed. First, the aerodynamic torque was accurately estimated through a proportional gain based observer where the generator speed is the measured output of the system. The torque signal contains not only useful frequencies of the wind, but also high frequencies and the ones due to structural vibration. The useful information of the wind signal is low frequency. A spectral analysis permitted the determination of the useful frequencies. The high frequencies were then filtered before introducing the torque signal in the wind speed observer. The desired effective wind speed was extracted through an integrator based observer using the previously estimated aerodynamic torque. The strength of the method is to avoid numerical solutions used in literature of the wind speed estimation. The effectiveness of the proposed wind speed estimator and its use to control the generator speed has been tested under turbulent situations using the FAST software (Fatigue, Aerodynamics, Structures, and Turbulence), for large scale Megawatt turbine.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1115-1119
• /
• 1996

The objective of this paper is to study on the idle speed control sing the fuzzy logic controller under load disturbance. The inputs of the fuzzy controller are error of rpm and rpm variation. The output of fuzzy controller is an ISC motor step. The airflow is controlled by the ISC motor movement and the idle speed is controlled by the airflow control. During the control, air to fuel ratio was checked by LAMBDA sensor. All experiments were carried in real vehicle.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.203-206
• /
• 1997

DC servo motors are widely used in many industrial fields as actuator of robot and driving power motors of electrical vehicle. Usually in the speed control systems, of motors, speed sensors are required and this fact results in the increased price and operating cost and the limited application of the motors. In this paper, a new speed control method for DC servo motor is proposed. In the scheme, the rotational speed is estimated by the measurement values of the armature voltage and current, instead of measurement by sensor. Optimal control theory is applied to design of the controller in construction of real system. This paper also report on the results of experiments to prove the validity of the proposed method.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.466-469
• /
• 2001

In this paper, closed loop V/f control of induction motor has been implemented by the estimated speed. Closed loop V/f control improve the performance of induction motor drive system at low speed compared to open loop V/f control. However, closed loop V/f control need speed sensor. By using the estimated speed, closed loop V/f control is possible without speed sensor. Rotor speed is calculated from the difference between synchronous frequency and slip angular frequency. 3-phase voltage reference is obtained from synchronous frequency. And the PWM technique using space vector PWM is applied in this scheme. In the space vector PWM, effective time of 3-phase voltage reference is used to simplify the calculation of effective voltage time. This scheme is simple to implement and one chip microprocessor was used in experimental system.

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1374-1381
• /
• 1994

This study suggests a new type shaft generating system driven by hydrostatic transmission suitable for small size vessels. In this system, the hydraulic motor speed is controlled by displacement adjustment using a 3-way high speed on/off valve. The 3-way high speed valve is operated by PWM control signal. In this study, a digital robust servo control algorithm is applied to the controller design of the system. By experiments and numerical computations, the frequency variation characteristics of the generating system under various disturbances are investigated. Conclusively, it is said that the shaft generating system proposed in this study shows excellent control performances.